HomeMy WebLinkAboutIdaho Food Code Informational CopyIDAHO FOOD CODE
Informational Copy
Food Protection Program
Boise, Idaho
1
THIS COPY OF THE IDAHO FOOD CODE IS NOT THE OFFICIAL COPY OF THE RULES AS THEY
APPEAR IN THE IDAHO ADMINISTRATIVE CODE. THIS IS A COMPILATION OF: 1) THE
UPDATED RULES, IDAPA 16.02.19, AND 2) THE 2013 FOOD CODE, WHICH IS ADOPTED BY
REFERENCE IN THE RULES AND INCORPORATED INTO THIS DOCUMENT.
TO VIEW AN OFFICIAL COPY OF THESE RULES, PLEASE ACCESS THE FOLLOWING INTERNET
ADDRESS: HTTPS://ADMINRULES.IDAHO.GOV/RULES/CURRENT/16/160219.PDF
FOR FURTHER INFORMATION, CONTACT:
ADMINISTRATIVE RULES
650 WEST STATE STREET, ROOM 100
P.O. BOX 83720
BOISE, ID 83720-0306
(208) 332-1820
Revised Jan 2024
2
PREFACE
WHY IS THERE A FOOD CODE?
Foodborne illness in the United States is a major cause of personal distress, preventable death, and avoidable
economic burden. It has been estimated that foodborne diseases cause approximately 48 million illnesses,
128,000 hospitalizations, and 3,000 deaths each year.
Epidemiological outbreak data repeatedly identify five major risk factors related to EMPLOYEE behaviors and
preparation practices in retail and FOOD SERVICE ESTABLISHMENTS as contributing to foodborne illness:
• Improper holding temperatures,
• Inadequate cooking of FOODS, such as undercooking EGGS,
• Contaminated EQUIPMENT,
• FOOD from unsafe sources, and
• Poor personal hygiene
The FOOD Code addresses controls for risk factors and further establishes five key public health interventions
to protect CONSUMER health. Specifically, these interventions are: demonstration of knowledge, EMPLOYEE
health controls, controlling hands as a vehicle of contamination, time and temperature parameters for
controlling pathogens, and the CONSUMER advisory. The first two interventions are found in Chapter 2 and
the last three in Chapter 3.
WHO IS RESPONSIBLE FOR FOOD SAFETY?
It is a shared responsibility of the FOOD industry and the government to ensure that FOOD provided to the
CONSUMER is safe and does not become a vehicle in a disease outbreak or in the transmission of
communicable disease. This shared responsibility extends to ensuring that CONSUMER expectations are met
and that FOOD in unADULTERATED, prepared in a clean environment, and honestly presented.
Accordingly, the provisions of the FOOD Code provide a system of prevention and overlapping safeguards
designed to minimize foodborne illness, as well as ensure EMPLOYEE health, industry manager knowledge,
safe FOOD, nontoxic and cleanable EQUIPMENT, and acceptable levels of SANITATION on FOOD ESTABLISHMENT
PREMISES; and promote fair dealings with the CONSUMER.
WHAT ARE UNIFORM STANDARDS?
The FOOD Code provides well-written, scientifically sound and up-to-date standards that are recognized as an
advantage by industry and governmental officials. Industry conformance with acceptable procedures is
much more likely where regulatory officials “speak with one voice” about what is required to protect the
public health, why it is important, and which alternatives for compliance may be accepted. It is useful to
business in that it provides accepted standards that can be applied in training and quality assurance
programs.
INFORMATION TO ASSIST THE USER
CHAPTER THROUGH SUBPARAGRAPH:
FOOD Code provisions address essentially four areas: personnel (Chapter 2), food (Chapter 3),
equipment/facilities/supplies (Chapter 4, 5, 6, 7), and compliance and enforcement (Chapter 8). The
structural nomenclature of the document is as follows:
Chapter 9
Part 9-1
Subpart 9-101
Section (§) 9-101.11
Paragraph (¶) 9-101.11(A)
Subparagraph 9-101.11(A)(1)
3
INFORMATION IN ITALICS:
Portions of some sections are written in italics. The provisions are not requirements, but are provided to
convey relevant information about specific exceptions and alternative means for compliance.
PRIORITY, PRIORITY FOUNDATION, AND CORE
Requirements contained in the FOOD Code are presented as being in one of three categories of importance:
PRIORITY ITEMS; PRIORITY FOUNDATION ITEMS (i.e., those that may or may not be critical; depending on the
circumstances); and CORE ITEMS.
A bold, superscripted letter P after a tagline (which is the language immediately following a section number
that introduces the subject of the section) indicates that all of the provisions within that section are PRIORITY
unless otherwise indicated, as follows:
Any provisions that are PRIORITY FOUNDATION ITEMS are followed by the bold, superscripted letter Pf. Any
unmarked provisions within a section that has a bold, superscripted letter P tagline are PRIORITY ITEMS. All
provisions following a tagline that is not marked with a P are CORE ITEMS.
DEFINED WORDS IN CAPS:
Defined words and terms are capitalized in the text of the FOOD Code chapters to alert the reader to the fact
that there is a specific meaning assigned to those words and terms and that the meaning of a provision is to
be interpreted in the defined context. A concerted effort was also made to capitalize all forms and
combinations of those defined words and terms that were intended to carry the weight of the definition.
IDAHO CHANGES TO THE FOOD CODE:
Additions, modifications and deletions added by the State of Idaho are preceded by the letters IDAPA and the
section numbers from the Idaho Administrative Rules 16.02.19 – FOOD SAFETY AND SANITATION STANDARDS FOR
FOOD ESTABLISHMENTS (THE IDAHO FOOD CODE).
4
IDAHO FOOD CODE
LEGAL AUTHORITY AND APPLICABILITY IDAPA 16.02.19.000-001
WRITTEN INTERPRETATIONS AND APPEALS IDAPA 16.02.19.002-003
INCORPORATION BY REFERENCE IDAPA 16.02.19-002
OFFICE AND CONFIDENTIALITY OF RECORDS IDAPA 16.02.19.005-006
CHAPTER 1 - PURPOSE AND DEFINITIONS
1-1 TITLE, INTENT, SCOPE PAGE 12
1-101 Title
1-102 Intent
1-103 Scope
1-2 DEFINITIONS
1-201 Applicability and Terms Defined
CHAPTER 2 - MANAGEMENT AND PERSONNEL
2-1 SUPERVISION PAGE 30
2-101 Responsibility
2-102 Knowledge
2-103 Duties
2-2 EMPLOYEE HEALTH
2-201 Disease or Medical Condition
2-3 PERSONAL CLEANLINESS
2-301 Hands and Arms
2-302 Fingernails
2-303 Jewelry
2-304 Outer Clothing
2-4 HYGIENIC PRACTICES
2-401 Food Contamination Prevention
2-402 Hair Restraints
2-403 Animals
CHAPTER 3 - FOOD
3-1 CHARACTERISTICS PAGE 44
3-101 Condition
3-2 SOURCES, SPECIFICATIONS, AND ORIGINAL CONTAINERS AND RECORDS
3-201 Sources
3-202 Specifications for Receiving
3-203 Original Containers and Records
5
3-3 PROTECTION FROM CONTAMINATION AFTER RECEIVING
3-301 Preventing Contamination by Employees
3-302 Preventing Food and Ingredient Contamination
3-303 Preventing Contamination from Ice, Coolant
3-304 Preventing Contamination from Equipment
3-305 Preventing Contamination from the Premises
3-306 Preventing Contamination by Consumers
3-307 Preventing Contamination from Other Sources
3-4 DESTRUCTION OF ORGANISMS OF PUBLIC HEALTH CONCERN
3-401 Cooking
3-402 Freezing
3-403 Reheating
3-5 LIMITATION OF GROWTH OF ORGANISMS OF PUBLIC HEALTH CONCERN
3-501 Temperature and Time Control
3-502 Specialized Processing Methods
3-6 FOOD IDENTITY, PRESENTATION, AND ON-PREMISES LABELING
3-601 Accurate Representation
3-602 Labeling
3-603 Consumer Advisory
3-7 CONTAMINATED FOOD
3-701Disposition
3-8 SPECIAL REQUIREMENTS FOR HIGHLY SUSCEPTIBLE POPULATIONS
3-801 Additional Safeguards
CHAPTER 4 - EQUIPMENT, UTENSILS AND LINENS
4-1 MATERIALS FOR CONSTRUCTION AND REPAIR PAGE 74
4-101 Multiuse
4-102 Single-Service and Single-Use
4-1 DESIGN AND CONSTRUCTION
4-201 Durability and Strength
4-202 Cleanability
4-203 Accuracy
4-204 Functionality
4-205 Acceptability
4-3 NUMBERS AND CAPACITIES
4-301 Equipment
4-302 Utensils, Temperature Measuring Devices
4-4 LOCATION AND INSTALLATION
4-401 Location
4-402 Installation
4-5 MAINTENANCE AND OPERATION
4-501 Equipment
4-502 Utensils and Temperature and Pressure Measuring
6
4-6 CLEANING OF EQUIPMENT AND UTENSILS
4-601 Objective
4-602 Frequency
4-603 Methods
4-7 CONTAMINATED FOOD
4-701 Objective
4-702 Frequency
4-703 Methods
4-8 SPECIAL REQUIREMENTS FOR HIGHLY SUSCEPTIBLE POPULATIONS
4-801 Objective
4-802 Frequency
4-803 Methods
4-9 PROTECTION OF CLEAN ITEMS
4-901 Drying
4-902 Lubricating and Reassembling
4-903 Storing
4-904 Handling
CHAPTER 5 - WATER, PLUMBING AND WASTE
5-1 WATER PAGE 96
5-101 Source
5-102 Quality
5-103 Quantity and Availability
5-104 Distribution, Delivery, and Retention
5-2 PLUMBING SYSTEM
5-201 Materials
5-202 Design, Construction, and Installation
5-203 Numbers and Capacities
5-204 Location and Placement
5-205 Operation and Maintenance
5-3 MOBILE WATER TANK AND MOBILE FOOD ESTABLISHMENT WATER TANK
5-301 Materials
5-302 Design and Construction
5-303 Numbers and Capacities
5-304 Operation and Maintenance
5-4 SEWAGE, OTHER LIQUID WASTE, AND RAINWATER
5-401 Mobile Holding Tank
5-402 Retention, Drainage, and Delivery
5-403 Disposal Facility
5-5 REFUSE, RECYCLABLES, AND RETURNABLES
5-501 Facilities on the Premises
5-502 Removal
5-503 Facilities for Disposal and Recycling
7
CHAPTER 6 - PHYSICAL FACILITIES
6-1 MATERIALS FOR CONSTRUCTION AND REPAIR PAGE 106
6-101 Source
6-102 Quality
6-2 DESIGN, CONTRUCTION, AND INSTALLATION
6-201 Cleanability
6-202 Functionality
6-3 NUMBERS AND CAPACITIES
6-301 Handwashing Facilities
6-302 Toilets and Urinals
6-303 Lighting
6-304 Ventilation
6-305 Dressing Areas and Lockers
6-306 Service Sinks
6-4 LOCATION AND PLACEMENT
6-401 Handwashing Facilities
6-402 Toilet Rooms
6-403 Employee Accommodations
6-404 Distressed Merchandise
6-405 Refuse, Recyclables, and Returnables
6-5 MAINTENANCE AND OPERATION
6-501 Premises, Structures, Attachments, and Fixtures
CHAPTER 7 - POISONOUS OR TOXIC MATERIALS
7-1 LABELING AND IDENTIFICATION PAGE 115
7-101 Original Containers
7-102 Working Containers
7-2 OPERATIONAL SUPPLIES AND APPLICATIONS
7-201 Storage
7-202 Presence and Use
7-203 Container Prohibitions
7-204 Chemicals
7-205 Lubricants
7-206 Pesticides
7-207 Medicines
7-208 First Aid Supplies
7-209 Other Personal Care Items
7-3 STOCK AND RETAIL SALE
7-301 Storage and Display
8
CHAPTER 8 - COMPLIANCE AND ENFORCEMENT
8-1 CODE APPLICABILITY PAGE 120
8-101 Use for Intended Purpose
8-102 Additional Requirements
8-103 Variances
8-2 PLAN SUBMISSION AND APPROVAL
8-201 Facility and Operating Plans
8-202 Confidentiality
8-203 Construction Inspection and Approval
8-3 PERMIT TO OPERATE
APPLICATION FOR A LICENSE IDAPA 16.02.19.830
8-301 Requirement
8-302 Application Procedure
8-303 Issuance
8-304 Conditions of Retention
SUMMARY SUSPENSION OF LICENSE IDAPA 16.02.19.831
8-4 INSPECTION AND CORRECTION OF VIOLATIONS
8-401 Frequency
8-402 Access
8-403 Report of Findings
8-404 Imminent Health Hazard
8-405 Priority Violation
8-406 Core Violation
INSPECTION SCORES IDAPA 16.02.19.841
VERIFICATION AND DOCUMENTATION OF
CORRECTION IDAPA 16.02.19.845
ENFORCEMENT INSPECTIONS IDAPA 16.02.19.850
8-5 PREVENTION OF FOODBORNE DISEASE TRANSMISSION BY EMPLOYEES
8-501 Investigation and Control
ENFORCEMENT PROCEDURES FOR
ADULTERATED OR MISBRANDED FOODS IDAPA 16.02.19.851
REVOCATION OF LICENSE IDAPA 16.02.19.860
CRIMINAL AND CIVIL PROCEEDINGS IDAPA 16.02.19.890
IDAPA 16.02.19
9
000. LEGAL AUTHORITY
The State of Idaho Board of Health and Welfare is authorized under Sections 37-121 and 39-1603,
Idaho Code, to adopt rules for the regulation of FOOD ESTABLISHMENTs to protect public health.
001. APPLICABILITY
01. These Rules Apply to Food Establishments. FOOD ESTABLISHMENTS as defined in Section 39-
1602, Idaho Code, must follow these rules. Those facilities include but are not limited to the
following:
a. Restaurants, catering facilities, taverns, kiosks, vending facilities, commissaries,
cafeterias, mobile FOOD facilities, TEMPORARY FOOD FACILITIES; and
b. Schools, senior centers, hospitals, residential care and treatment facilities, nursing
homes, correctional facilities, camps, FOOD banks, and church facilities; and
c. Retail markets, MEAT, FISH, delicatessen, bakery and supermarkets, convenience stores,
health FOOD stores, and neighborhood markets; and
d. FOOD, water and BEVERAGE processing and bottling facilities that manufacture, process
and distribute FOOD, water and BEVERAGES within the state of Idaho, and are not
inspected for FOOD safety by a federal agency.
02. These Rules Do Not Apply to These Establishments.
a. AGRICULTURAL MARKETS as exempted in Section 39-1602, Idaho Code.
b. Bed-and-breakfast operations that prepare and offer FOOD for breakfast only to guests.
The number of guest beds must not exceed ten (10) beds as defined in Section 39-1602,
Idaho Code.
c. Day care facilities regulated by Sections 39-1101 through 39-1119, Idaho Code.
d. LICENSED outfitters and guides regulated by Sections 36-2101 through 36-2119, Idaho
Code.
e. LOW-RISK FOOD ESTABLISHMENTS, as exempted in Section 39-1602, Idaho Code, which offer
only non-TIME/TEMPERATURE CONTROL FOR SAFETY (NON-TCS) FOODS.
f. FARMERS MARKET vendors and ROADSIDE STANDS that only offer or sell NON-
TIME/TEMPERATURE CONTROL FOR SAFETY (NON-TCS) FOODS or COTTAGE FOODS.
g. Non-profit charitable, fraternal, or benevolent organizations that do not prepare or
serve FOOD on a regular basis as exempted in Section 39-1602, Idaho Code. FOOD is not
considered to be served on a regular basis if it is not served for more than five (5)
consecutive days on no more than three (3) occasions per year for FOODs which are not
TIME/TEMPERATURE CONTROL FOR SAFETY FOODS. For all other FOOD, it must not be served
more than one (1) meal per week.
h. Private homes where FOOD is prepared or served for family consumption or receives
catered or home-delivered FOOD as exempted by Section 39-1602, Idaho Code.
i. COTTAGE FOOD OPERATIONS, when the consumer is informed and must be provided
contact information for the COTTAGE FOOD OPERATIONS as follows:
1. By a clearly legible label on the product PACKAGING; or a clearly visible
placard at the sales or service location that also states:
2. The FOOD was prepared in a home kitchen that is not subject to regulation
and inspection by the REGULATORY AUTHORITY; and
3. The FOOD may contain allergens.
03. How to Use this Chapter of Rules. The rules in this chapter are modifications, additions or
deletions made to the federal publication incorporated by reference in Section 004 of these
rules. In order to follow these rules, that publication is required. (Note: that publication is
incorporated in this document). Changes to those standards are listed in this chapter of rules
10
by listing which section of the publication is being modified at the beginning of each section of
rule.
002. INCORPORATION BY REFERENCE
The DEPARTMENT is adopting by reference the “FOOD Code 2013 Recommendations of the United
States Public Health Service, Food and Drug Administration,” Publication PB2013-110462. A
certified copy of this publication may be reviewed at the main office of the DEPARTMENT of Health and
Welfare. It is also available online at:
www.fda.gov/Food/GuidanceRegulation/RetailFoodProtection/FoodCode/ucm374275.htm.
This publication is being adopted with modifications and additions as follows:
01. Chapter 1, Purpose and Definitions. Additions and modifications have been made to this
chapter. See Sections 100-199 for these rules.
02. Chapter 2, Management and Personnel. Modifications have been made to this chapter. See
sections 200-299 of these rules.
03. Chapter 3, Food. Modifications have been made to this chapter. See sections 300-399 of
these rules.
04. Chapter 4, Equipment, Utensils, and Linens. This chapter has been adopted with no
modifications.
05. Chapter 5, Water, Plumbing and Waste. This chapter has been adopted with no
modifications.
06. Chapter 6, Physical Facilities. Modifications have been made to this chapter. See sections
600-699 of these rules.
07. Chapter 7, Poisonous or Toxic Materials. Modifications have been made to this chapter.
See sections 700-799 of these rules.
08. Chapter 8, Compliance and Enforcement. Modifications have been made to this chapter.
See sections 800-899 of these rules.
09. Annexes 1 through 7 are excluded. These sections have not been adopted.
003. OFFICE – OFFICE HOURS – MAILING ADDRESS – STREET ADDRESS – INTERNET WEBSITE
01. Office Hours. Office hours are 8 a.m. to 5 p.m., Mountain Time, Monday through Friday,
except holidays designated by the State of Idaho.
02. Mailing Address. The mailing address for the business office is Idaho Department of Health
and Welfare, Food Protection Program, P.O. Box 83720, Boise, ID 83720-0036.
03. Street Address. The business office of the Idaho Department of Health and Welfare is located
at 450 West State Street, Boise, Idaho 83702.
04. Telephone. (208) 334-5500.
05. Internet Website. http://www.healthandwelfare.idaho.gov.
01.
004. – 049. (RESERVED)
050. TRAINING AND INFORMATIONAL MATERIALS. The DEPARTMENT is authorized under Section 56-
1007, Idaho Code, to establish a reasonable charge for training and informational materials that are
provided to the public.
051. – 099. (RESERVED)
11
CHAPTER 1 - PURPOSE AND DEFINITIONS
PARTS
1-1 TITLE, INTENT, SCOPE
1-2 DEFINITIONS
1-1 TITLE, INTENT, SCOPE
SUBPARTS 1-101 Title
1-102 Intent
1-103 Scope
IDAPA 16.02.19.100 PURPOSES AND DEFINITIONS
Section 100-199 will be used for modifications and additions to Chapter 1 of the 2013 Food Code as
referenced in Section 004 of these rules.
IDAPA 16.02.19.110 DEFINITIONS AND ABBREVIATIONS -- A THROUGH K.
The definitions defined in this section are modifications or additions to the definitions and terms provided in
the 2013 Food Code.
TITLE
1-101.10 FOOD CODE
These provisions shall be known as the Food Code, hereinafter referred to as “this Code.”
INTENT
1-102.10 FOOD SAFETY, ILLNESS PREVENTION, AND HONEST PRESENTATION
The purpose of the Code is to safeguard public health and provide to CONSUMERS FOOD that is safe,
unADULTERATED, and honestly presented.
SCOPE
1-103.10 STATEMENT
This Code establishes definitions; sets standards for management and personnel, FOOD operations, and
EQUIPMENT and facilities; and provides for FOOD ESTABLISHMENT plan review, PERMIT issuance, inspection,
EMPLOYEE RESTRICTION, and PERMIT suspension.
1-2 DEFINITIONS
SUBPARTS 1-201 Applicability and Terms Defined
APPLICABILITY AND TERMS DEFINED
1-201.10 STATEMENT OF APPLICATION AND LISTING OF TERMS
(A) The following definitions apply in the interpretation and application of this Code. The definitions shown
as IDAPA 16.02.19.110 and IDAPA 16.02.19.111 are modifications or additions to the definitions in 2013
Food Code.
(B) Terms Defined. As used in this Code, each of the terms listed in ¶1-201.10(B) shall have the meaning
stated below.
12
ACCREDITED PROGRAM
1) “ACCREDITED PROGRAM" means a FOOD protection manager certification program that has been
evaluated and listed by an accrediting agency as conforming to national standards for
organizations that certify individuals.
2) "ACCREDITED PROGRAM" refers to the certification process and is a designation based upon an
independent evaluation of factors such as the sponsor's mission; organizational structure; staff
resources; revenue sources; policies; public information regarding program scope, eligibility
requirements, re-certification, discipline and grievance procedures; and test development and
administration.
3) "ACCREDITED PROGRAM" does not refer to training functions or educational programs.
ADDITIVE
1) "FOOD ADDITIVE" has the meaning stated in the Federal FOOD, Drug, and Cosmetic act, §201(s)
and 21 CFR 170.3(e).
2) "COLOR ADDITIVE" has the meaning stated in the Federal FOOD, Drug, and Cosmetic Act, §201(t)
and 21 CFR70.3(f).
ADULTERATED
1) "ADULTERATED" has the meaning stated in the Federal FOOD, Drug, and Cosmetic Act, § 402.
AGRICULTURAL MARKET - IDAPA 16.02.19.110.01
1) Any venue where fixed or mobile retail FOOD ESTABLISHMENT can engage in the sale of raw or
fresh fruits, vegetables and nuts in the shell. It may also include the sale of factory SEALED non-
TIME/TEMPERATURE CONTROL FOR SAFETY FOODS. AGRICULTURAL MARKET means the same as “FARMERS
MARKET” or “ROADSIDE STAND.”
APPROVED
1) "APPROVED" means acceptable to the REGULATORY AUTHORITY based on a determination of
conformity with principles, practices, and generally recognized standards that protect public
health.
ASYMPTOMATIC
1) "ASYMPTOMATIC" means without obvious symptoms; not showing or producing indications of a
disease or other medical condition, such as an individual infected with a pathogen but not
exhibiting or producing any signs or symptoms of vomiting, diarrhea, or jaundice.
2) "ASYMPTOMATIC" includes not showing symptoms because symptoms have resolved or subsided,
or because symptoms never manifested.
aw
1) "aw" means water activity which is a measure of the free moisture in a FOOD, is the quotient of
the water vapor pressure of the substance divided by the vapor pressure of pure water at the
same temperature, and is indicated by the symbol AW.
BALUT
1) "BALUT" means an embryo inside a fertile EGG that has been incubated for a period sufficient for
the embryo to reach a specific state of development after which it is removed from incubation
before hatching.
BEVERAGE
1) "BEVERAGE" means a liquid for drinking, including water.
BOARD - IDAPA 16.02.19.110.02
1) The State of Idaho Board of Health and Welfare as established in Section 56-1005, Idaho Code.
BOTTLED DRINKING WATER
1) "BOTTLED DRINKING WATER" means water that is SEALED in bottles, packages, or other containers
and offered for sale for human consumption, including bottled mineral water.
13
CERTIFICATION NUMBER (NATIONAL SHELLFISH SANITATION PROGRAM)
1) "CERTIFICATION NUMBER" means a unique combination of letters and numbers assigned by a
shellfish CONTROL AUTHORITY to a MOLLUSCAN SHELLFISH DEALER according to the provisions of the
National Shellfish Sanitation Program.
CFR
1) "CFR" means CODE OF FEDERAL REGULATIONS. Citations in the Code to the CFR refer sequentially to
the Title, Part, and Section numbers, such as 40 CFR 180.194 refers to Title 40, Part 180, and
Section 194.
2) "Code of Federal Regulations" means the compilation of the general and permanent rules
published in the Federal Register by the executive departments and agencies of the federal
government which:
a) Is published annually by the U.S. Government Printing Office;
b) Contains FDA rules in 21 CFR, USDA rules in 7 CFR and 9 CFR, EPA rules in 40 CFR, and
Wildlife and Fisheries rules in 50 CFR.
CIP
1) "CIP" means cleaned in place by the circulation or flowing by mechanical means through a
piping system of a detergent solution, water rinse, and SANITIZING solution, onto or over
EQUIPMENT surfaces that require cleaning, such as the method used, in part, to clean and SANITIZE
a frozen dessert machine.
2) "CIP" does not include the cleaning of EQUIPMENT such as band saws, slicers, or mixers that are
subject to in-place manual cleaning without the use of a CIP system.
COMMINGLE
1) To combine SHELLSTOCK harvested on different days or from different growing areas as identified
on the tag or label, or
2) To combine SHUCKED SHELLFISH from containers with different container codes or different
shucking dates.
COMMISSARY - IDAPA 16.02.19.110.03
1) A COMMISSARY is a place where FOOD containers or supplies are stored, prepared, or PACKAGED for
transit, sale, or service at other locations.
COMMINUTED
1) "COMMINUTED" means reduced in size by methods including chopping, flaking, grinding, or
mincing.
2) "COMMINUTED" includes FISH OR MEAT products that are reduced in size and restructured or
reformulated such as gefilte FISH, gyros, ground beef, and sausage; and a mixture of 2 or more
types of MEAT that have been reduced in size and combined, such as sausages made from 2 or
more MEATS.
CONDITIONAL EMPLOYEE
1) "CONDITIONAL EMPLOYEE" means a potential FOOD EMPLOYEE to whom a job offer is made,
conditional on responses to subsequent medical questions or examinations designed to identify
potential FOOD EMPLOYEES who may be suffering from a disease that can be transmitted through
food and done in compliance with Title 1 of the Americans with Disabilities Act of 1990.
CONFIRMED DISEASE OUTBREAK
1) "CONFIRMED DISEASE OUTBREAK" means a FOODBORNE DISEASE OUTBREAK in which laboratory analysis
of appropriate specimens identifies a causative agent and epidemiological analysis implicates
the FOOD as the source of the illness.
CONSENT ORDER - IDAPA 16.02.16.110.04
1) A CONSENT ORDER is an enforceable agreement between the REGULATORY AUTHORITY and the LICENSE
HOLDER to correct violations that caused the actions taken by the REGULATORY AUTHORITY.
14
CONSUMER
1) "CONSUMER" means a PERSON who is a member of the public, takes possession of FOOD, is not
functioning in the capacity of an operator of a FOOD ESTABLISHMENT or FOOD PROCESSING PLANT, and
does not offer the FOOD for resale.
CORE ITEM - IDAPA 16.02.16.110.04
1) A provision in the incorporated Food Code that is not designated as a priority item or a priority
foundation item and includes items that usually relate to general sanitation, operation controls,
sanitation standard operating procedures (SSOPs), facilities or structures, equipment design, or
general maintenance.
CORROSION-RESISTANT MATERIAL
1) "CORROSION-RESISTANT MATERIAL" means a material that maintains acceptable surface cleanability
characteristics under prolonged influence of the FOOD to be contacted, the normal use of
cleaning compounds and sanitizing solutions, and other conditions of the use environment.
COTTAGE FOOD OPERATION - IDAPA 16.02.16.110.05
1) A COTTAGE FOOD OPERATION is when a person or business prepares or produces COTTAGE FOOD
PRODUCTS in the home kitchen of that person’s primary residence or other designated kitchen or
location.
COTTAGE FOOD PRODUCT - IDAPA 16.02.16.110.06
1) COTTAGE FOOD PRODUCTS are NON-TIME/TEMPERATURE CONTROL FOR SAFETY (NON-TCS) FOODS that are
sold directly to a consumer. Examples of COTTAGE FOODS may include, but are not limited to:
baked goods, fruit jams and jellies, fruit pies, breads, cakes, pastries and cookies, candies and
confections, dried fruits, dry herbs, seasonings and mixtures, cereals, trail mixes and granola,
nuts, vinegar, popcorn and popcorn balls, and cotton candy.
COUNTER-MOUNTED EQUIPMENT
1) “COUNTER-MOUNTED EQUIPMENT” means EQUIPMENT that is not portable and is designed to be
mounted off the floor on a table, counter, or shelf.
CRITICAL CONTROL POINT
1) "CRITICAL CONTROL POINT" means a point or procedure in a specific FOOD system where loss of
control may result in an unacceptable health RISK.
CRITICAL LIMIT
1) "CRITICAL LIMIT" means the maximum or minimum value to which a physical, biological, or
chemical parameter must be controlled at a CRITICAL CONTROL POINT to minimize the RISK that the
identified FOOD safety HAZARD may occur.
CUT LEAFY GREENS
1) "CUT LEAFY GREENS" means fresh leafy greens whose leaves have been cut, shredded, sliced,
chopped, or torn. The term "leafy greens" includes iceberg lettuce, romaine lettuce, leaf lettuce,
butter lettuce, baby leaf lettuce (i.e., immature lettuce or leafy greens), escarole, endive, spring
mix, spinach, cabbage, kale, arugula and chard. The term "leafy greens" does not include herbs
such as cilantro or parsley.
DEALER
1) "DEALER" means a PERSON who is authorized by a SHELLFISH CONTROL AUTHORITY for the activities of
SHELLSTOCK shipper, shucker-packer, repacker, reshipper, or depuration processor of MOLLUSCAN
SHELLFISH according to the provisions of the National Shellfish Sanitation Program.
DEPARTMENT - IDAPA 16.02.19.110.07
1) The Idaho Department of Health and Welfare as established in Section 56-1002, Idaho Code.
15
DIRECTOR - IDAPA 16.02.19.110.08
1) The Director of the Idaho Department of Health and Welfare as established in Section 56-1003,
Idaho Code.
DISCLOSURE
1) "DISCLOSURE" means a written statement that clearly identifies the animal-derived FOODS which
are, or can be ordered, raw, undercooked, or without otherwise being processed to eliminate
pathogens, or items that contain an ingredient that is raw, undercooked, or without otherwise
being processed to eliminate pathogens.
DRINKING WATER
1) "DRINKING WATER" means water that meets criteria as specified in 40 CFR 141 National Primary
Drinking Water Regulations.
2) "DRINKING WATER" is traditionally known as "potable water".
3) "DRINKING WATER" includes the term "water" except where the term used connotes that the water
is not potable, such as "boiler water," "mop water," "rainwater," "wastewater," and "nondrinking"
water.
DRY STORAGE AREA
1) “DRY STORAGE AREA" means a room or area designated for the storage of PACKAGED or
containerized bulk FOOD that is not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD and dry goods
such as SINGLE-SERVICE items.
EASILY CLEANABLE
1) "EASILY CLEANABLE" means a characteristic of a surface that:
a) Allows effective removal of soil by normal cleaning methods;
b) Is dependent on the material, design, construction, and installation of the surface; and
c) Varies with the likelihood of the surface's role in introducing pathogenic or toxigenic agents
or other contaminants into FOOD based on the surface's APPROVED placement, purpose, and
use.
2) "EASILY CLEANABLE" includes a tiered application of the criteria that qualify the surface as EASILY
CLEANABLE as specified in Subparagraph (a) of this definition to different situations in which
varying degrees of cleanability are required such as:
a) The appropriateness of stainless steel for a FOOD preparation surface as opposed to the lack
of need for stainless steel to be used for floors or for tables used for CONSUMER dining; or
b) The need for a different degree of cleanability for a utilitarian attachment or accessory in
the kitchen as opposed to a decorative attachment or accessory in the CONSUMER dining area.
EASILY MOVABLE
1) Portable; mounted on casters, gliders, or rollers; or provided with a mechanical means to safely
tilt a unit of EQUIPMENT for cleaning; and
2) Having no utility connection, a utility connection that disconnects quickly, or a flexible utility
connection line of sufficient length to allow the EQUIPMENT to be moved for cleaning of the
EQUIPMENT and adjacent area.
EGG
1) “EGG" means the shell EGG of avian species such as chicken, duck, goose, guinea, quail, RATITES or
turkey.
2) "EGG" does not include:
a) A BALUT;
b) The EGG of reptile species such as alligator or
c) An EGG product
16
EGG PRODUCT
1) “EGG PRODUCT” means all, or a portion of, the contents found inside EGGS separated from the shell
and pasteurized in a FOOD PROCESSING PLANT, with or without added ingredients, intended for
human consumption, such as dried, frozen or liquid EGGS.
2) “EGG PRODUCT” does not include FOOD which contains EGGS only in a relatively small portion such as
cake mixes.
EMBARGO - IDAPA 16.02.19.110.09
1) An action taken by the REGULATORY AUTHORITY that places a FOOD product or EQUIPMENT used in
FOOD production on hold until a determination is made on the product's safety.
EMPLOYEE
1) "EMPLOYEE" means the PERMIT HOLDER, PERSON IN CHARGE, FOOD EMPLOYEE, PERSON having supervisory
or management duties, PERSON on the payroll, family member, volunteer, PERSON performing
work under contractual agreement, or other PERSON working in a FOOD ESTABLISHMENT.
ENFORCEMENT INSPECTION - IDAPA 16.02.19.110.10
1) An inspection conducted by the REGULATORY AUTHORITY when compliance with these rules by a
FOOD ESTABLISHMENT is lacking and violations remain uncorrected after the first follow-up
inspection to a routine inspection.
EPA
1) "EPA" means the U.S. Environmental Enforcement Agency.
EQUIPMENT
1) "EQUIPMENT” means an article that is used in the operation of a FOOD ESTABLISHMENT such as a
freezer, grinder, hood, ice maker, MEAT block, mixer, oven, reach-in refrigerator, scale, sink,
slicer, stove, and table, TEMPERATURE MEASURING DEVICE for ambient air, VENDING MACHINE, or
WAREWASHING machine.
2) "EQUIPMENT" does not include items used for handling or storing large quantities of PACKAGED FOODS
that are received from a supplier in a cased or overwrapped lot, such as hand trucks, forklifts,
dollies, pallets, racks, and skids.
EXCLUDE
1) "EXCLUDE” means to prevent a PERSON from working as an EMPLOYEE in a FOOD ESTABLISHMENT
entering a FOOD ESTABLISHMENT as an EMPLOYEE.
FARMERS MARKET - IDAPA 16.02.19.110.11
1) Any fixed or MOBILE RETAIL FOOD ESTABLISHMENT at which farmer producers sell agricultural
products directly to the general public. FARMERS MARKET means the same as “AGRICULTURAL
MARKET” and “ROADSIDE STANDS.”
FDA
1) "FDA" means the U.S. Food and Drug Administration.
FISH
1) "FISH" means fresh or saltwater finfish, crustaceans and other forms of aquatic life (including
alligator, frog, aquatic turtle, jellyfish, sea cucumber, and sea urchin and the roe of such animals)
other than birds or mammals, and all mollusks, if such animal life is intended for human
consumptions.
2) "FISH" includes an edible human FOOD product derived in whole or in part from FISH, including
FISH that have been processed in any manner.
FOOD
1) "FOOD" means a raw, cooked, or processed edible substance, ice, BEVERAGE, or ingredient used or
intended for use or for sale in whole or in part for human consumption, or chewing gum.
17
FOODBORNE DISEASE OUTBREAK
1) "FOODBORNE DISEASE OUTBREAK" means the occurrence of two or more cases of a similar illness
resulting from the ingestion of a common FOOD.
FOOD-CONTACT SURFACE
1) A surface of EQUIPMENT or a utensil with which FOOD normally comes into contact; or
2) A surface of EQUIPMENT or a utensil from which FOOD may drain, drip, or splash:
a) Into a FOOD, or
b) Onto a surface normally in contact with FOOD.
FOOD EMPLOYEE
1) "FOOD EMPLOYEE" means an individual working with unpacked FOOD, FOOD EQUIPMENT or UTENSILS,
or FOOD-CONTACT SURFACES.
FOOD ESTABLISHMENT
1) “FOOD ESTABLISHMENT" means an operation that:
a) Stores, prepares, packages, serves, vends FOOD directly to the CONSUMER, or otherwise
provides FOOD for human consumption such as a restaurant; satellite or catered feeding
location; catering operation if the operation provides FOOD directly to a CONSUMER or to a
conveyance used to transport PEOPLE; market; vending location; conveyance used to
transport people; institution; or FOOD bank; and
b) Relinquishes possession of FOOD to a CONSUMER directly or indirectly through a delivery
service such as home delivery of grocery orders or restaurant takeout orders, or delivery
service that is provided by common carriers.
2) "FOOD ESTABLISHMENT" includes:
a) An element of the operation such as a transportation vehicle or a central preparation facility
that supplies a vending location or satellite feeding location unless the vending or feeding
location is permitted by the REGULATORY AUTHORITY; and
b) An operation that is conducted in a mobile, stationary, temporary, or permanent facility or
location; where consumption is on or off the PREMISES; and regardless of whether there is a
charge for the FOOD.
3) "FOOD ESTABLISHMENT" does not include:
a) An ESTABLISHMENT that offers only pre-PACKAGED FOODS that are not TIME/TEMPERATURE CONTROL
FOR SAFETY FOODS;
b) A produce stand that only offers whole, uncut fresh fruits and vegetables;
c) IDAPA 16.02.19.110.14(a) - Modification to Section 1-201.10 “FOOD ESTABLISHMENT” by
deleting (3)(c)
d) A kitchen in a private home if only FOOD that is not TIME/TEMPERATURE CONTROL FOR SAFETY
FOOD, is prepared for sale or service at a function such as a religious or charitable
organization's bake sale if allowed by LAW and if the CONSUMER is informed by a clearly visible
placard at the sales or service location that the FOOD is prepared in a kitchen that is not
subject to regulation and inspection by the REGULATORY AUTHORITY;
e) An area where FOOD that is prepared as specified in Subparagraph (3)(d) of this definition is
sold or offered for human consumption;
f) A kitchen in a private home; such as a small family day-care provider; or a bed-and-breakfast
operation that prepares and offers FOOD to guests if the home is owner occupied, the number of
available guest bedrooms does not exceed 10, breakfast is the only meal offered, the number of
guests served does not exceed 18, and the CONSUMER is informed by statements contained in
published advertisements, mailed brochures, and placards posted at the registration area that
the FOOD is prepared in a kitchen that is not regulated and inspected by the REGULATORY
AUTHORITY; or
g) A private home that receives catered or home-delivered FOOD.
h) IDAPA 16.02.19.110.14(b) – Modification to Section 1-201.10 “FOOD ESTABLISHMENT” by
adding subparagraph 3(h) to clarify that a COTTAGE FOOD OPERATION is not a FOOD
ESTABLISHMENT.
18
FOOD PROCESSING PLANT
1) "FOOD PROCESSING PLANT" means a commercial operation that manufactures, packages, labels, or
stores FOOD for human consumption and does not provide FOOD directly to a CONSUMER.
2) IDAPA 16.02.19.110.15 - Modification of Section 2-201-10 "FOOD PROCESSING PLANT” by
deleting subparagraph (2) of the term “FOOD PROCESSING PLANT” in the 2013 Food Code.
GAME ANIMAL
1) "GAME ANIMAL" means an animal, the products of which are FOOD, that is not classified as cattle,
sheep, swine, goat, horse, mule, or other equine in 9 CFR Subchapter A - Mandatory MEAT
Inspection, Part 301, as POULTRY in 9 CFR Subchapter C - Mandatory POULTRY Products
Inspection, Part 381, or as FISH as defined under Subparagraph 1-201.10.
2) "GAME ANIMAL" includes mammals such as reindeer, elk, deer, antelope, water buffalo, bison,
rabbit, squirrel, opossum, raccoon, nutria, or muskrat, and nonaquatic reptiles such as land
snakes.
3) "GAME ANIMAL" does not include RATITES such as ostrich, emu, and rhea.
GENERAL USE PESTICIDE
1) "GENERAL USE PESTICIDE" means a pesticide that is not classified by EPA for restricted use as
specified in 40 CFR 152.175 Pesticides classified for restricted use.
GOOD RETAIL PRACTICE - IDAPA 16.02.19.110.14
1) "GOOD RETAIL PRACTICE" means the preventive measures that include practices and procedures
that effectively control the introduction of pathogens, chemicals, and physical objects into food.
GRADE A STANDARDS
1) "GRADE A STANDARDS" means the requirements of the United States Public Health Service/FDA
"Grade A Pasteurized Milk Ordinance" with which certain fluid and dry milk and milk products
comply.
HACCP PLAN
1) "HACCP PLAN" means a written document that delineates the formal procedures for following
the HAZARD analysis and CRITICAL CONTROL POINT principles developed by the National Advisory
Committee of Microbiological Criteria for FOODS.
HANDWASHING SINK
1) "HANDWASHING SINK" means a lavatory, a basin or vessel for washing, a wash basin, or a PLUMBING
FIXTURE especially placed for use in personal hygiene and designed for the washing of the hands.
2) "HANDWASHING SINK" includes an automatic handwashing facility.
HAZARD
1) "HAZARD" means a biological, chemical, or physical property that may cause an unacceptable
CONSUMER health RISK.
HEALTH PRACTITIONER
1) "HEALTH PRACTITIONER" means a physician LICENSED to practice medicine, or if allowed by LAW, a
nurse practitioner, physician assistant, or similar medical professional.
HERMETICALLY SEALED CONTAINER
1) "HERMETICALLY SEALED CONTAINER" means a container that is designed and intended to be secure
against the entry of microorganisms and, in the case of low acid canned FOODS, to maintain the
commercial sterility of its contents after processing.
19
HIGH-RISK FOOD ESTABLISHMENT - IDAPA 16.02.19.110.15
1) A HIGH-RISK ESTABLISHMENT does the following operations:
a) Extensive handling of raw ingredients;
b) Preparation processes that include the cooking, cooling and reheating of TIME/TEMPERATURE
CONTROL FOR SAFETY (TCS) FOODS
c) A variety of processes requiring hot and cold holding of TIME/TEMPERATURE CONTROL FOR
SAFETY (TCS)FOODS.
HIGHLY SUSCEPTIBLE POPULATION
1) "HIGHLY SUSCEPTIBLE POPULATION" means PERSONS who are more likely than other people in the
general population to experience foodborne disease because they are:
a) Immunocompromised; preschool age children, or older adults; and
b) Obtaining FOOD at a facility that provides services such as custodial care, health care, or
assisted living, such as a child or adult day care center, kidney dialysis center, hospital or
nursing home, or nutritional or socialization services such as a senior center.
INTERMITTENT FOOD ESTABLISHMENT - Section 39-1607(3), Idaho Code
1) An INTERMITTENT FOOD ESTABLISHMENT is a FOOD vendor that operates for a period of time, not to
exceed three (3) days per week, at a single, specified location in conjunction with a recurring
event and that offers TIME/TEMPERATURE CONTROL FOR SAFETY (TCS) FOODS to the general public.
Examples of a recurring event may be a FARMERS’ or community market, or a holiday market. An
INTERMITTENT FOOD ESTABLISHMENT does not include the vendor of farm fresh ungraded EGGS at a
recurring event.
IMMINENT HEALTH HAZARD
1) "IMMINENT HEALTH HAZARD" means a significant threat or danger to health that is considered to
exist when there is evidence sufficient to show that a product, practice, circumstance, or event
creates a situation that requires immediate correction or cessation of operation to prevent
injury based on:
a) The number of potential injuries, and
b) The nature, severity, and duration of the anticipated injury.
INJECTED
1) "INJECTED" means manipulating MEAT to which a solution has been introduced into its interior by
processes that are referred to as "injecting," "pump marinating," or "stitch pumping".
JUICE
(1) "JUICE" means the aqueous liquid expressed or extracted from one or more fruits or vegetables,
purees of the edible portions of one or more fruits or vegetables, or any concentrates of such
liquid or puree.
(2) "JUICE" does not include, for purposes of HACCP, liquids, purees, or concentrates that are not used
as BEVERAGES or ingredients of BEVERAGES.
KITCHENWARE
1) "KITCHENWARE" means FOOD preparation and storage UTENSILS.
LAW
1) "LAW" means applicable local, state, and federal statutes, regulations, and ordinances.
LINENS
1) "LINENS" means fabric items such as cloth hampers, cloth napkins, table cloths, wiping cloths,
and work garments including cloth gloves.
LICENSE - IDAPA 16.02.19.111.01
1) The term "LICENSE" is used in these rules the same as the term "PERMIT" is used in the 2013 FOOD
Code.
20
LICENSE HOLDER - IDAPA 16.02.19.111.02
1) The term "LICENSE HOLDER" is used in the rules the same as the term "PERMIT HOLDER" is used in
the 2013 Food Code.
LOW-RISK FOOD ESTABLISHMENT - IDAPA 16.02.19.111.03
1) A LOW-RISK FOOD ESTABLISHMENT provides factory-SEALED, pre-PACKAGED, non-TIME/TEMPERATURE
CONTROL FOR SAFETY (NON-TCS) FOODS. The ESTABLISHMENT may have limited preparation of non-
TIME/TEMPERATURE CONTROL FOR SAFETY (NON-TCS) FOODS only.
MAJOR FOOD ALLERGEN
(1) “MAJOR FOOD ALLERGEN” means:
a) Milk, EGG, FISH (such as bass, flounder, cod, and including crustacean shellfish such as crab,
lobster, or shrimp), tree nuts (such as almonds, pecans, or walnuts), wheat, peanuts, and
soybeans; or
b) A FOOD ingredient that contains protein derived from a FOOD, as specified in Subparagrap0h
(1)(a) of this definition.
(2) “MAJOR FOOD ALLERGEN” does not include:
a) Any highly refined oil derived from a FOOD specified in Subparagraph (1)(a) of this definition
and any ingredient derived from such highly refined oil; or
b) Any ingredient that is exempt under the petition or notification process specified in the FOOD
Allergen Labeling and CONSUMER Protection Act of 2004 (Public LAW 108-282).
MEAT
1) "MEAT" means the flesh of animals used as FOOD including the dressed flesh of cattle, swine,
sheep, or goats and other edible animals, except FISH, POULTRY, and wild GAME ANIMALS as specified
under Subparagraphs 3-201.17(A)(3) & (4).
MECHANICALLY TENDERIZED
1) “MECHANICALLY TENDERIZED" means manipulating MEAT with deep penetration by processes which
may be referred to as "blade tenderizing," "jaccarding," "pinning," "needling," or using blades,
pins, needles or any mechanical device.
2) "MECHANICALLY TENDERIZED" does not include processes by which solutions are INJECTED into MEAT.
MEDIUM-RISK FOOD ESTABLISHMENT - IDAPA 16.02.19.111.04
1) "MEDIUM-RISK FOOD ESTABLISHMENT" includes the following:
a) A limited menu of (1) or (2) main items;
b) Pre-PACKAGED raw ingredients cooked or prepared to order; or
c) Raw ingredients requiring minimal assembly; or
d) products are cooked or prepared and serviced immediately; or
e) Hot and cold holding OF TIME/TEMPERATURE CONTROL FOR SAFETY (TCS)FOODS is restricted to
single meal service.
MG/L
1) "mg/L" means milligrams per liter, which is the metric equivalent of parts per million (ppm).
MOBILE FOOD ESTABLISHMENT - Section 39-1607(4), Idaho Code
1) A Mobile FOOD ESTABLISHMENT is a FOOD ESTABLISHMENT selling or serving FOOD for human
consumption from any vehicle or other temporary or itinerant station and includes any movable
FOOD SERVICE ESTABLISHMENT, truck, van, trailer, pushcart, bicycle, watercraft or other movable
FOOD service with or without wheels, including hand-carried, portable containers in or on which
FOOD or BEVERAGE is transported, stored or prepared for retail sale or given away at temporary
locations.
MOLLUSCAN SHELLFISH
1) "MOLLUSCAN SHELLFISH" means any edible species of fresh or frozen oysters, clams, mussels, and
scallops or edible portions thereof, except when the scallop product consists only of the shucked
adductor muscle.
21
NON-CONTINUOUS COOKING
1) "Non-Continuous Cooking" means the cooking of FOOD in a FOOD ESTABLISHMENT using a process
in which the initial heating of the FOOD is intentionally halted so that it may be cooled and held
for complete cooking at a later time prior to sale or service.
2) "Non-Continuous Cooking" does not include cooking procedures that only involve temporarily
interrupting or slowing an otherwise continuous cooking process.
PACKAGED
1) "PACKAGED" means bottled, canned, cartoned, bagged, or wrapped, whether PACKAGED in A FOOD
ESTABLISHMENT or A FOOD PROCESSING PLANT.
2) "PACKAGED" does not include wrapped or placed in a carry-out container to protect the FOOD during
service or delivery to the CONSUMER, by a FOOD EMPLOYEE, upon CONSUMER request.
PERMIT
1) "PERMIT" means the document issued by the REGULATORY AUTHORITY that authorizes a PERSON to
operate a FOOD ESTABLISHMENT.
PERMIT HOLDER
1) "PERMIT HOLDER" means the entity that:
a) Is legally responsible for the operation of the FOOD ESTABLISHMENT such as the owner, the
owner's agent, or other PERSON; and
b) Possesses a valid PERMIT to operate a FOOD ESTABLISHMENT.
PERSON
1) "PERSON" means an association, a corporation, individual, partnership, other legal entity,
government, or governmental subdivision or agency.
PERSON IN CHARGE
1) "PERSON IN CHARGE" means the individual present at a FOOD ESTABLISHMENT who is responsible for
the operation at the time of inspection.
PERSONAL CARE ITEMS
1) "PERSONAL CARE ITEMS" means items or substances that may be poisonous, toxic, or a source of
contamination and are used to maintain or enhance a PERSON’S health, hygiene, or appearance.
2) "PERSONAL CARE ITEMS" include items such as medicines; first aid supplies; and other items such
as cosmetics, and toiletries such as toothpaste and mouthwash.
pH
1) "pH" means the symbol for the negative logarithm of the hydrogen ion concentration, which is a
measure of the degree of acidity or alkalinity of a solution.
2) Values between 0 and 7 indicate acidity and value between 7 and 14 indicate alkalinity. The
value for pure distilled water is 7, which is considered neutral.
PHYSICAL FACILITIES
1) "PHYSICAL FACILITIES" means the structure and interior surfaces of a FOOD ESTABLISHMENT including
accessories such as soap and towel dispensers and attachments such as light fixtures and
heating or air conditioning system vents.
PLUMBING FIXTURE
1) "PLUMBING FIXTURE" means a receptacle or device that:
a) Is permanently or temporarily connected to the water distribution system of the PREMISES
and demands a supply of water from the system; or
b) Discharges used water, waste materials, or SEWAGE directly or indirectly to the drainage
system of the PREMISES.
22
PLUMBING SYSTEM
1) "PLUMBING SYSTEM" means the water supply and distribution pipes; PLUMBING FIXTURES and traps;
soil, waste, and vent pipes; sanitary and storm sewers and building drains, including their
respective connections, devices, and appurtenances within the PREMISES; and water-treating
EQUIPMENT.
POISONOUS OR TOXIC MATERIALS
1) "POISONOUS OR TOXIC MATERIALS" means substances that are not intended for ingestion and are
included in 4 categories:
a) Cleaners and SANITIZERS, which include cleaning and SANITIZING agents and agents such as
caustics, acids, drying agents, polishes, and other chemicals;
b) Pesticides, except SANITIZERS, which include substances such as insecticides and rodenticides;
c) Substances necessary for the operation and maintenance of the ESTABLISHMENT such as
nonFOOD grade lubricants and PERSONAL CARE ITEMS that may be deleterious to health; and
d) Substances that are not necessary for the operation and maintenance of the ESTABLISHMENT
and are on the PREMISES for retail sale, such as petroleum products and paints.
POULTRY
1) "POULTRY" means:
a) Any domesticated bird (chickens, turkeys, ducks, geese, guineas, RATITES, or squabs),
whether live or dead, as defined in 9 CFR 381.1 POULTRY Products Inspection Regulations
Definitions, POULTRY; and
b) Any migratory waterfowl or game bird, pheasant, partridge, quail, grouse, or pigeon,
whether live or dead, as defined in 9 CFR 362.1 Voluntary POULTRY Inspection Regulations,
Definitions.
PREMISES
1) "PREMISES" means
a) The PHYSICAL FACILITY, its contents, and the contiguous land or property under the control off
the PERMIT HOLDER; or
b) The PHYSICAL FACILITY, its contents, and the land or property not described under
Subparagraph (a) of this definition if its facilities and contents are under the control of the
PERMIT HOLDER and may impact FOOD ESTABLISHMENT personnel, facilities, or operations, and a
FOOD ESTABLISHMENT is only one component of a larger operation such as a health care
facility, hotel, motel, school, recreational camp, or prison.
PRIMAL CUT
1) "PRIMAL CUT" means: a basic major cut into which carcasses and sides of MEAT are separated,
such as a beef round, pork loin, lamb flank, or veal breast.
PRIORITY ITEM - IDAPA 16.02.19.111.05
1) A provision in the incorporated Food Code whose application contributes directly to the
elimination, prevention, or reduction to an acceptable level, hazards associated with foodborne
illness or injury, and there is no other provision that more directly controls the hazard. A
priority item includes items with a quantifiable measure to show control of hazards such as
cooking, r
PRIORITY FOUNDATION ITEM - IDAPA 16.02.19.111.06
1) A provision in the incorporated Food Code whose application supports, facilitates, or
enables one (1) or more priority items. Priority foundation item includes an item that
requires the purposeful incorporation of specific actions, equipment, or procedures by
industry management to attain control of risk factors that contribute to foodborne illness or
injury such as personnel training, infrastructure or necessary equipment, HACCP plans,
documentation or record keeping, and labeling. A priority foundation item is an item that is
denoted in the incorporated Food Code with a superscript (Pf).
23
PUBLIC WATER SYSTEM
1) "PUBLIC WATER SYSTEM" has the meaning stated in 40 CFR 141 National Primary DRINKING WATER
Regulations.
READY-TO-EAT FOOD
1) "READY-TO-EAT FOOD" means FOOD that:
a) Is in a form that is edible without additional preparation to achieve FOOD safety, as specified
under one of the following: ¶3-401.11(A) or (B), § 3-401.12, or § 3-402.11, or as specified
in ¶ 3-401.11(C); or
b) Is a raw or partially cooked animal FOOD and the CONSUMER is advised as specified in
Subparagraphs 3-401.11(D)(1) and (3); or
c) Is prepared in accordance with a VARIANCE that is granted as specified in Subparagraphs 3-
401.11(D)(4); and
d) May receive additional preparation for palatability or aesthetic, epicurean, gastronomic, or
culinary purposes.
2) "READY-TO-EAT FOOD" includes:
a) Raw animal FOOD that is cooked as specified under § 3-401.11 or 3-401.12, or frozen as
specified under § 3-402.11;
b) Raw fruits and vegetables that are washed as specified under § 3-302.15;
c) Fruits and vegetables that are cooked for hot holding, as specified under § 3-401.13;
d) All TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is cooked to the temperature and time
required for the specific FOOD under Subpart 3-401 and cooled as specified under § 3-
501.14;
e) Plant FOOD for which further washing, cooking, or other processing is not required for FOOD
safety, and from which rinds, peels, husks, or shells, if naturally present are removed;
f) Substances derived from plants such as spices, seasonings, and sugar;
g) A bakery item such as bread, cakes, pies, fillings, or icing for which further cooking is not
required for FOOD safety;
h) The following products that are produced in accordance with USDA guidelines and that
have received a lethality treatment for pathogens; dry, fermented sausages, such as dry
salami or pepperoni; salt-cured MEAT and POULTRY PRODUCTS, such as prosciutto ham, country
cured ham, and Parma ham; and dried MEAT and POULTRY products, such as jerky or beef
sticks; and
i) FOODS manufactured as specified in 21 CFR Part 113, Thermally Processed Low-acid FOOD
PACKAGED in HERMETICALLY SEALED CONTAINERS.
REDUCED OXYGEN PACKAGING
1) "REDUCED OXYGEN PACKAGING" means:
a) The reduction of the amount of oxygen in a PACKAGE by removing oxygen; displacing oxygen
and replacing it with another gas or combination of gases; or otherwise controlling the
oxygen content to a level below that normally found in the atmosphere (approximately 21%
at sea level); and
b) A process as specified in Subparagraph (1)(a) of this definition that involves a FOOD for
which the HAZARDS Clostridium botulinum or Listeria monocytogenes require control in
the final PACKAGED form.
2) "REDUCED OXYGEN PACKAGING" includes:
a) Vacuum PACKAGING, in which air is removed from a PACKAGE of FOOD and the PACKAGE is
HERMETICALLY SEALED so that a vacuum remains inside the PACKAGE;
b) Modified atmosphere PACKAGING, in which the atmosphere of a PACKAGE of FOOD is modified
so that composition is different from air but the atmosphere may change over time due to
the permeability of the PACKAGING material or the respiration of the FOOD. Modified
atmosphere packaging includes reduction in the proportion of oxygen, total replacement of
oxygen, or an increase in the proportion of other gases such as carbon dioxide or nitrogen;
c) Controlled atmosphere PACKAGING, in which the atmosphere of a PACKAGE of FOOD is modified
so that until the PACKAGE is opened, its composition if different from air, and continuous
control of that atmosphere is maintained, such as by using scavengers or a combination of
total replacement of oxygen, nonrespiring FOOD, and impermeable packaging material;
24
d) Cook chill PACKAGING, in which cooked FOOD is hot filled into impermeable bags which have
the air expelled and are then SEALED or crimped closed. The bagged FOOD is rapidly chilled
and refrigerated at temperatures that inhibit the growth of psychotropic pathogens; or
e) Sous vide PACKAGING, in which raw or partially cooked FOOD is vacuum-PACKAGED in an
impermeable bag, cooked in the bag, rapidly chilled, and refrigerated at temperatures that
inhibit the growth of psychotropic pathogens.
REFUSE
1) "REFUSE" means solid waste not carried by water through the sewage system.
REGULATORY AUTHORITY - IDAPA 16.02.19.111.07
1) The DEPARTMENT or its designee is the REGULATORY AUTHORITY authorized to enforce compliance of
these rules.
2) The DEPARTMENT is responsible for preparing the rules, rule amendments, standards, policy
statements, operational procedures, program assessments and guidelines.
3) The seven (7) Public Health Districts and the Division of Licensing and Certification have been
designated by the DIRECTOR as the REGULATORY AUTHORITY for the purpose of issuing LICENSES,
collecting fees, conducting inspections, reviewing plans, determining compliance with the rules,
investigating complaints and illnesses, examining FOOD, EMBARGOING FOOD and enforcing these
rules.
REMINDER
1) "REMINDER" means a written statement concerning the health RISK of consuming animal FOODS
raw, undercooked, or without otherwise being processed to eliminate pathogens.
RE-SERVICE
1) "RE-SERVICE" means the transfer of FOOD that is unused and returned by a CONSUMER after being
served or sold and in the possession of the CONSUMER, to another PERSON.
RESTRICT
1) "RESTRICT" means to limit the activities of a FOOD EMPLOYEE so that there is no RISK of transmitting
a disease that is transmissible through FOOD and the FOOD EMPLOYEE does not work with exposed
FOOD, clean EQUIPMENT, UTENSILS, LINENS, or unwrapped SINGLE-SERVICE or SINGLE-USE ARTICLES.
RESTRICTED EGG
1) "RESTRICTED EGG" means any check, dirty EGG, incubator reject, inedible, leaker, or loss as defined
in 9 CFR 590.
RESTRICTED USE PESTICIDE
1) "RESTRICTED USE PESTICIDE" means a pesticide product that contains the active ingredients
specified in 40 CFR 152.175 Pesticides classified for RESTRICTED USE, and that is limited to use by
or under the direct supervision of a certified applicator.
RISK
1) "RISK" means the likelihood that an adverse health effect will occur within a population as a
result of a HAZARD in a FOOD.
RISK CONTROL PLAN - IDAPA 16.02.19.111.08
1) "RISK CONTROL PLAN" is a document describing the specific actions to be taken by the LICENSE
HOLDER to address and correct a continuing HAZARD or RISK within the FOOD ESTABLISHMENT.
RISK FACTOR VIOLATION - IDAPA 16.02.19.111.09
1) "RISK FACTOR VIOLATION" means improper practices or procedures which are most frequently
identified by epidemiologic investigation as a cause of foodborne illness or injury.
25
ROADSIDE STAND - IDAPA 16.02.19.111.10
1) "ROADSIDE STAND" means any fixed or mobile retail FOOD ESTABLISHMENT at which an individual
farmer producer sells AGRICULTURAL PRODUCTS directly to CONSUMERS. ROADSIDE STAND means the
same as “AGRICULTURAL MARKET” and “FARMERS MARKET”.
SAFE MATERIAL
1) "SAFE MATERIAL" means:
a) An article manufactured from or composed of materials that may not reasonably be
expected to result, directly or indirectly, in their becoming a component or otherwise
affecting the characteristics of any FOOD;
b) An ADDITIVE that is used as specified in § 409 of the Federal FOOD, Drug, and Cosmetic Act; or
c) Other materials that are not ADDITIVES and that are used in conformity with applicable
regulations of the FOOD and Drug Administration.
SANITATION
1) "SANITATION" means the application of cumulative heat or chemicals on cleaned FOOD-CONTACT
SURFACES that, when evaluated for efficacy, is sufficient to yield a reduction of 5 logs, which is
equal to a 99.999% reduction, of representative disease microorganisms of public health
importance.
SEALED
1) "SEALED" means free of cracks or other openings that allow the entry or passage of moisture.
SERVICE ANIMAL
1) "SERVICE ANIMAL" means an animal such as a guide dog, signal dog, or other animal individually
trained to provide assistance to an individual with a disability.
SERVICING AREA
1) "SERVICING AREA" means an operating base location to which a MOBILE FOOD ESTABLISHMENT or
transportation vehicle returns regularly for such things as vehicle and EQUIPMENT cleaning,
discharging liquid or solid wastes, refilling water tanks and ice bins, and boarding FOOD.
SEWAGE
1) "SEWAGE" means liquid waste containing animal or vegetable matter in suspension or solution
and may include liquids containing chemicals in solution.
SHELLFISH CONTROL AUTHORITY
1) "SHELLFISH CONTROL AUTHORITY" means a state, federal, foreign, tribal, or other government entity
legally responsible for administering a program that includes certification of MOLLUSCAN
SHELLFISH harvesters and DEALERS for interstate commerce.
SHELLFISH CONTROL AUTHORITY
1) "SHELLSTOCK" means raw, in-shell MOLLUSCAN SHELLFISH.
SHIGA TOXIN-PRODUCING ESCHERICHIA COLI
1) "SHIGA TOXIN-PRODUCING ESCHERICHIA COLI" (STEC) means any E. coli capable of producing Shiga
toxins (also called verocytotoxins).STEC infections can be ASYMPTOMATIC or may result in a
spectrum of illness ranging from mild non-bloody diarrhea, to hemorrhagic colitis (i.e. bloody
diarrhea), to hemolytic uremic syndrome (HUS - a type of kidney failure). Examples of
serotypes of STEC include: E. coli O157:H7; E. coli O157:NM; E. coli O26:H11; E. coli O125:NM;
E. coli O103:H2; and E. coli O111:NM. STEC are sometimes referred to as VTEC
(verocytotoxigenic E. coli) or as EHED (Enterohemorrhagic E. coli). EHEC are a subset of STEC
which can cause hemorrhagic colitis or HUS.
SHUCKED SHELLFISH
1) "SHUCKED SHELLFISH" means MOLLUSCAN SHELLFISH that have one or both shells removed.
26
SINGLE-SERVICE ARTICLES
1) "SINGLE-SERVICE ARTICLES" means TABLEWARE, carry-out UTENSILS, and other items such as bags,
containers, placemats, stirrers, straws, toothpicks, and wrappers that are designed and
constructed for one time, one PERSON use after which they are intended for discard.
SINGLE-USE-ARTICLES
1) "SINGLE-USE ARTICLES" means UTENSILS and bulk FOOD containers designed and constructed to be
used once and discarded.
2) "SINGLE-USE ARTICLES" includes items such as wax paper, butcher paper, plastic wrap, formed
aluminum FOOD containers, jars, plastic tubs or buckets, bread wrappers, pickle barrels, ketchup
bottles, and number 10 cans which do not meet the materials, durability, strength, and
cleanability specifications under §§ 4-101.11, 4-201.11, and 4-202.11 for multiuse UTENSILS.
SLACKING
1) "SLACKING" means the process of moderating the temperature of a FOOD such as allowing a FOOD
to gradually increase from a temperature of -23°C (-10°F) to -4°C (25°F) in preparation for
deep-fat frying or to facilitate even heat penetration during the cooking of previously block-
frozen FOOD such as spinach.
SMOOTH
1) "SMOOTH" means:
a) A FOOD-CONTACT SURFACE having a surface free of pits and inclusions with a cleanability equal
to or exceeding that of (100 grit) number 3 stainless steel;
b) A non-FOOD-CONTACT SURFACE of EQUIPMENT having a surface equal to that of commercial
grade hot-rolled steel free of visible scale; and
c) A floor, wall, or ceiling having an even or level surface with no roughness or projections that
render it difficult to clean.
TABLEWARE
1) "TABLEWARE" means eating, drinking, and serving UTENSILS for table use such as flatware
including forks, knives, and spoons; hollowware including bowls, cups, serving dishes, and
tumblers; and plates.
TEMPERATURE MEASURING DEVICE
1) "TEMPERATURE MEASURING DEVICE" means a thermometer, thermocouple, thermistor, or other
device that indicates the temperature of FOOD, air, or water.
TEMPORARY FOOD ESTABLISHMENT
1) "TEMPORARY FOOD ESTABLISHMENT" means a FOOD ESTABLISHMENT that operates for a period of no
more than 14 consecutive days in conjunction with a single event or celebration.
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD
1) "TIME/TEMPERATURE CONTROL FOR SAFETY FOOD" means a FOOD that requires TIME/TEMPERATURE
CONTROL FOR SAFETY (TCS) to limit pathogenic microorganism growth or toxin formation.
2) "TIME/TEMPERATURE CONTROL FOR SAFETY FOOD" includes:
a) An animal FOOD that is raw or heat-treated; a plant FOOD that is heat-treated or consists of
raw seed sprouts, cut melons, CUT LEAFY GREENS, cut tomatoes or mixtures of cut tomatoes
that are not modified in a way to that they are unable to support pathogenic microorganism
growth or toxin formation, or garlic-in-oil mixtures that are not modified in a way so that
they are unable to support pathogenic microorganism growth or toxin formation;
b) Except as specified in Subparagraph (3)(d) of this definition, a FOOD that because of the
interaction of its Aw and pH values is designated as Product Assessment Required (PA) in
Table A or B of this definition:
27
Table A. Interaction of pH and Aw for control of spores in FOOD heat-treated to destroy
vegetative cells and subsequently PACKAGED.
Aw values pH: 4.6 or less pH: > 4.6 – 5.6 pH: > 5.6
≤ 0.92 non-TCS Food* non-TCS Food non-TCS Food
> 0.92 – 0.95 non-TCS Food non-TCS Food PA**
> 0.95 non-TCS Food PA PA
*TCS FOOD means Time/Temperature Control for Safety FOOD
**PA means Product Assessment required
Table B. Interaction of pH and Aw for control of vegetative cells and spores in FOOD not heat-
treated or heat-treated but not PACKAGED.
Aw values pH: < 4.2 pH: 4.2 – 4.6 pH: > 4.6 – 5.0 pH: > 5.0
< 0.88 non-TCS Food* non-TCS Food non-TCS Food non-TCS Food
0.88 – 0.90 non-TCS Food non-TCS Food non-TCS Food PA**
> 0.90 – 0.92 non-TCS Food non-TCS Food PA PA
> 0.92 non-TCS Food PA PA PA
*TCS FOOD means Time/Temperature Control for Safety FOOD
**PA means Product Assessment required
3) “TIME/TEMPERATURE CONTROL FOR SAFETY FOOD" does not include:
a) An air-cooled hard-boiled EGG with shell intact, or an EGG with shell intact that is not hard-
boiled, but has been pasteurized to destroy all viable salmonellae;
b) A FOOD in an unopened HERMETICALLY SEALED CONTAINER that is commercially processed to
achieve and maintain commercial sterility under conditions of non-refrigerated storage and
distribution;
c) A FOOD that because of its pH or Aw value, or interaction of Aw and pH values, is designated as
a non-TCS FOOD in Table A or B of this definition;
d) A FOOD that is designated as Product Assessment Required (PA) in Table A or B of this
definition and has undergone a Product Assessment showing that the growth or toxin
formation of pathogenic microorganisms that are reasonable likely to occur in that FOOD is
precluded due to:
i.) Intrinsic factors including added or natural characteristics of the FOOD such as
preservatives, antimicrobials, humectants, acidulants, or nutrients,
ii.) Extrinsic factors including environmental or operational factors that affect the FOOD
such as packaging, modified atmosphere such as REDUCED OXYGEN PACKAGING, shelf life
and use, or temperature range of storage and use, or
iii.) A combination of intrinsic and extrinsic factors; or
e) A FOOD that does not support the growth or toxin formation of pathogenic microorganisms in
accordance with one of the Subparagraphs (3)(a)-(3)(d) of this definition even though the
FOOD may contain a pathogenic microorganism or chemical or physical contaminant at a level
sufficient to cause illness or injury.
USDA
1) "USDA" means the U.S. Department of Agriculture
UTENSIL
1) "UTENSIL" means a FOOD-CONTACT implement or container used in the storage, preparation,
transportation, dispensing, sale, or service of FOOD, such as KITCHENWARE or TABLEWARE that is
multiuse, SINGLE-SERVICE, or SINGLE-USE; gloves used in contact with FOOD; temperature sensing
probes of FOOD TEMPERATURE MEASURING DEVICES; and probe-type price or identification tags used
in contact with FOOD.
28
VARIANCE
1) "VARIANCE" means a written document issued by the REGULATORY AUTHORITY that authorizes a
modification or waiver of one or more requirements of this Code if, in the opinion of the
REGULATORY AUTHORITY a health HAZARD or nuisance will not result from the modification or
waiver.
VENDING MACHINE
1) "VENDING MACHINE" means a self-service device that, upon insertion of a coin, paper currency,
token, card, or key, or by optional manual operation, dispenses unit servings of FOOD in bulk or
in packages without the necessity of replenishing the device between each vending operation.
VENDING MACHINE LOCATION
1) "VENDING MACHINE LOCATION" means the room, enclosure, space, or area where one or more
VENDING MACHINES are installed and operated and includes the storage areas and areas on the
PREMISES that are used to service and maintain the VENDING MACHINES.
WAREWASHING
1) "WAREWASHING" means the cleaning and SANITIZING of UTENSILS and FOOD-CONTACT SURFACES of
EQUIPMENT.
WHOLE-MUSCLE, INTACT BEEF
1) "WHOLE-MUSCLE, INTACT BEEF" means whole muscle beef that is not INJECTED, MECHANICALLY
TENDERIZED, reconstructed, or scored and marinated, from which beef steaks may be cut.
29
CHAPTER 2 - Management and Personnel
2-1 SUPERVISION
2-2 EMPLOYEE HEALTH
2-3 PERSONAL CLEANLINESS
2-4 HYGIENIC PRACTICES
2-5 RESPONDING TO CONTAMINATION EVENTS
2-1 SUPERVISION
SUBPARTS 2-101 Responsibility
2-102 Knowledge
2-103 Duties
RESPONSIBILITY
2-101.11 ASSIGNMENT
IDAPA 16.02.19.201 ASSIGNMENT OF PERSON IN CHARGE
Modification to Section 2-101.11(A). The LICENSE HOLDER will be the PERSON IN CHARGE or will designate a
PERSON IN CHARGE and will ensure that a PERSON IN CHARGE is present at the FOOD ESTABLISHMENT during all hours
of FOOD preparation and service. Pf
Modification to Section 2-101.11(B). This section has not been adopted.
KNOWLEDGE
2-102.11 DEMONSTRATION
Based on the RISKS inherent to the FOOD operation, during inspections and upon request the PERSON IN CHARGE
shall demonstrate to the REGULATORY AUTHORITY knowledge of foodborne disease prevention, application of
the hazard analysis and critical control point principles, and the requirements of this Code.
DEMONSTRATION OF KNOWLEDGE
Modification to Section 2-102.11(A). The PERSON IN CHARGE of a FOOD ESTABLISHMENT may demonstrate
knowledge on the RISKS of foodborne illness or health HAZARDS by one (1) of the following:
A) 2-102.11(A) MODIFIED BY IDAPA 16.02.19.210.01 DEMONSTRATION OF KNOWLEDGE
No Priority Violations. Complying with the incorporated FOOD Code by not having any priority
violations at the time of inspection. Pf
(B) Being a certified FOOD protection manager who has shown proficiency of required information
through passing a test that is part of an ACCREDITED PROGRAM. Pf
(C) Responding correctly to the inspector's questions as they relate to the specific FOOD operation. The
areas of knowledge include:
(1) Describing the relationship between the prevention of foodborne disease and the personal
hygiene of a FOOD EMPLOYEE. Pf
(2) Explaining the responsibility of the PERSON IN CHARGE for preventing the transmission of
foodborne disease by a FOOD EMPLOYEE who has a disease or medical condition that may cause
foodborne disease; Pf
(3) Describing the symptoms associated with the diseases that are transmissible through FOOD; Pf
(4) Explaining the significance of the relationship between maintaining the time and temperature
of TIME/TEMPERATURE CONTROL FOR SAFETY FOOD and the prevention of foodborne illness; Pf
30
(5) Explaining the HAZARDS involved in the consumption of raw or undercooked MEAT, POULTRY, EGGS,
and FISH; Pf
(6) Stating the required FOOD temperatures and times for safe cooking of TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD including MEAT, POULTRY, EGGS, & FISH; Pf
(7) Stating the required temperatures and times for the safe refrigerated storage, hot holding,
cooling, and reheating of TIME/TEMPERATURE CONTROL FOR SAFETY FOOD; Pf
(8) Describing the relationship between the prevention of foodborne illness and the management
and control of the following:
(a) Cross contamination, Pf
(b) Hand contact with READY-TO-EAT FOODS, Pf
(c) Handwashing, Pf and
(d) Maintaining the FOOD ESTABLISHMENT in a clean condition and in good repair, Pf
(9) Describing FOODs identified as MAJOR FOOD ALLERGENS and the symptoms that a MAJOR FOOD
ALLERGEN could cause in a sensitive individual who has an allergic reaction. Pf
(10) Explaining the relationship between FOOD safety and providing EQUIPMENT that is:
(a) Sufficient in number and capacity, Pf and
(b) Properly designed, constructed, located, installed, operated, maintained, and cleaned; Pf
(11) Explaining correct procedures for cleaning and sanitizing UTENSILS and FOOD-CONTACT SURFACES
of EQUIPMENT; Pf
(12) Identifying the source of water used and measures taken to ensure that it remains protected
from contamination such as providing protection from backflow and precluding the creation of
cross connections; Pf
(13) Identifying POISONOUS OR TOXIC MATERIALS in the FOOD ESTABLISHMENT and the procedures
necessary to ensure that they are safely stored, dispense, used, and disposed of according to
LAW; Pf
(14) Identifying CRITICAL CONTROL POINTS in the operation from purchasing through sale or service
that when not controlled may contribute to the transmission of foodborne illness and
explaining steps taken to ensure that the points are controlled in accordance with the
requirements of this Code; Pf
(15) Explaining the details of how the PERSON IN CHARGE and FOOD EMPLOYEES comply with the HACCP
plan if a plan is required by the LAW, this Code, or an agreement between the REGULATORY
AUTHORITY and the FOOD ESTABLISHMENT; Pf
(16) Explaining the responsibilities, rights, and authorities assigned by this Code to the:
(a) FOOD EMPLOYEE, Pf
(b) CONDITIONAL EMPLOYEE, Pf
(c) PERSON IN CHARGE, Pf
(d) REGULATORY AUTHORITY, Pf
(17) Explaining how the PERSON IN CHARGE, FOOD EMPLOYEES, and CONDITIONAL EMPLOYEES comply with
reporting responsibilities and EXCLUSION or RESTRICTION of FOOD EMPLOYEES. Pf
IDAPA 16.02.19.210.02 APPROVED COURSES.
(D) Completion of the Idaho FOOD Safety and Sanitation Manual, or an equivalent course designed to meet
the same training as the Idaho FOOD Safety and Sanitation Manual.
31
2-102.12 CERTIFIED FOOD PROTECTION MANAGER – IDAPA 16.02.19.210.03
(A) At least one EMPLOYEE that has supervisory and management responsibility and the authority to direct
and control FOOD preparation and service shall be a CERTIFIED FOOD PROTECTION MANAGER who has shown
proficiency of required information through passing a test that is part of an ACCREDITED PROGRAM.
(B) This section does not apply to certain types of FOOD ESTABLISHMENTS deemed by the REGULATORY AUTHORITY
to pose minimal risk of causing, or contributing to, foodborne illness based on the nature of the
operation and extent of FOOD preparation.
2-102.20 FOOD PROTECTION MANAGER CERTIFICATION
(A) A PERSON IN CHARGE who demonstrates knowledge by being a FOOD protection manager that is certified
by a FOOD protection manager certification program that is evaluated and listed by a Conference for
FOOD Protection-recognized accrediting agency as conforming to the Conference for FOOD Protection
Standards for Accreditation of FOOD Protection Manager Certification Programs is deemed to comply
with ¶ 2-102.11(B).
(B) A FOOD ESTABLISHMENT that has an EMPLOYEE that is certified by a FOOD protection manager certification
program that is evaluated and listed by a Conference for FOOD Protection-recognized accrediting
agency as conforming to the Conference for FOOD Protection Standards for Accreditation of FOOD
Protection Manager Certification Programs is deemed to comply with § 2-102.12.
DUTIES
2-103.11 PERSON IN CHARGE
The PERSON IN CHARGE shall ensure that:
(A) FOOD ESTABLISHMENT operations are not conducted in a private home or in a room used as living or
sleeping quarters as specified under § 6-202.111; Pf
(B) PERSONS unnecessary to the FOOD ESTABLISHMENT operation are not allowed in the FOOD preparation,
FOOD storage, or WAREWASHING areas, except that brief visits and tours may be authorized by the PERSON
IN CHARGE if steps are taken to ensure that exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and
unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES are protected from contamination; Pf
(C) EMPLOYEES and other PERSONS such as delivery and maintenance PERSONS and pesticide applicators
entering the FOOD preparation, FOOD storage, and WAREWASHING areas comply with this Code; Pf
(D) EMPLOYEES are effectively cleaning their hands, by routinely monitoring the EMPLOYEES' handwashing; Pf
(E) EMPLOYEES are visibly observing FOODS as they are received to determine that they are from APPROVED
sources, delivered at the required temperatures, protected from contamination, UNADULTERATED, and
accurately presented, by routinely monitoring the EMPLOYEES' observations and periodically evaluating
FOODS upon their receipt; Pf
(F) EMPLOYEES are verifying that FOODS delivered to the FOOD ESTABLISHMENT during non-operating hours
are from APPROVED sources and are placed into appropriate storage locations such that they are
maintained at the required temperatures, protected from contamination, UNADULTERATED, and
accurately presented; Pf
(G) EMPLOYEES are properly cooking TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, being particularly careful
in cooking those FOODS known to cause severe foodborne illness and death, such as EGGS and
COMMINUTED MEATS, through daily oversight of the EMPLOYEES' routine monitoring of the cooking
temperatures using appropriate TEMPERATURE MEASURING DEVICES properly scaled and calibrated as
specified under § 4-203.11 and ¶ 4-502.11(B); Pf
(H) EMPLOYEES are using proper methods to rapidly cool TIME/TEMPERATURE CONTROL FOR SAFETY FOODS that
are not held hot or are not for consumption within 4 hours, through daily oversight of the EMPLOYEES’
routine monitoring of FOOD temperatures during cooling; Pf
(I) CONSUMERS who order raw; or partially cooked READY-TO-EAT FOODS of animal origin are informed as
specified under § 3-603.11 that the FOOD is not cooked sufficiently to ensure its safety; Pf
32
(J) EMPLOYEES are properly SANITIZING cleaned multiuse EQUIPMENT and UTENSILS before they are reused,
through routine monitoring of solution temperature and exposure time for hot water SANITIZING, and
chemical concentration, pH, temperature, and exposure time for chemical SANITIZING; Pf
(K) CONSUMERS are notified that clean TABLEWARE is to be used when they return to SELF-SERVICE areas such
as salad bars and buffets as specified under § 3-304.16; Pf
(L) Except when APPROVAL is obtained from the REGULATORY AUTHORITY as specified in ¶ 3-301.11(E),
EMPLOYEES are preventing cross-contamination of READY-TO-EAT FOOD with bare hands by properly
using suitable UTENSILS such as deli tissue, spatulas, tongs, single-use gloves, or dispensing EQUIPMENT.
Pf
(M) EMPLOYEES are properly trained in FOOD safety, including FOOD allergy awareness, as it relates to their
assigned duties; Pf
(N) FOOD EMPLOYEES and CONDITIONAL EMPLOYEES are informed in a verifiable manner of their responsibility
to report in accordance with LAW, to the PERSON IN CHARGE, information about their health and activities
as they relate to diseases that are transmissible through FOOD as specified under ¶ 2-201.11(A); Pf
(O) Written procedures and plans, where specified by this Code and as developed by the FOOD
ESTABLISHMENT, are maintained and implemented as required. Pf
2-2 EMPLOYEE HEALTH
SUBPARTS 2-201 Responsibilities of Permit Holder, Persons in Charge, Food
Employees, and Conditional Employees
DISEASE OR MEDICAL CONDITION
2-201.11 RESPONSIBILITY OF PERMIT HOLDER, PERSON IN CHARGE, AND CONDITIONAL
EMPLOYEES
(A) The PERMIT HOLDER shall require FOOD EMPLOYEES and CONDITIONAL EMPLOYEES to report to the PERSON IN
CHARGE information about their health and activities as they relate to diseases that are transmissible
through FOOD. A FOOD EMPLOYEE or CONDITIONAL EMPLOYEE shall report the information in a manner that
allows the PERSON IN CHARGE to reduce the RISK of foodborne disease transmission, including providing
necessary additional information, such as the date of onset of symptoms and an illness, or of a
diagnosis without symptoms, if the FOOD EMPLOYEE or CONDITIONAL EMPLOYEE:
(1) Has any of the following symptoms:
(a) Vomiting, P
(b) Diarrhea, P
(c) Jaundice, P
(d) Sore throat with fever, P or
(e) A lesion containing pus such as a boil or infected wound that is open or draining and is:
(i.) On the hands or wrists, unless an impermeable cover such as a finger cot or stall
protects the lesion and a SINGLE-USE glove is worn over the impermeable cover, P
(ii.) On exposed portions of the arms, unless the lesion is protected by an impermeable
cover, P or
33
(iii.) On other parts of the body, unless the lesion is covered by a dry, durable, tight-
fitting bandage, P
(2) Has an illness diagnosed by a HEALTH PRACTITIONER due to:
(a) Norovirus, P
(b) Hepatitis A virus, P
(c) Shigella spp., P
(d) SHIGA TOXIN-PRODUCING ESCHERICHIA COLI, P
(e) Salmonella Typhi; P or
(f) Nontyphoidal Salmonella; P
(3) Had a previous illness, diagnosed by a HEALTH PRACTITIONER, within the past 3 months due to
SALMONELLA Typhi, without having received antibiotic therapy, as determined by a HEALTH
PRACTITIONER, P
(4) Has been exposed to, or is the suspected source of, a CONFIRMED DISEASE OUTBREAK, because the
FOOD EMPLOYEE or CONDITIONAL EMPLOYEE consumed or prepared FOOD implicated in the
outbreak, or consumed FOOD at an event prepared by a PERSON who is infected or ill with:
(a) Norovirus within the past 48 hours of the last exposure, P
(b) SHIGA TOXIN-PRODUCING ESCHERICHIA COLI or Shigella spp. within the past 3 days of the last
exposure, P
(c) Salmonella Typhi within the past 14 days of the last exposure, P or
(d) Hepatitis A virus within the past 30 days of the last exposure, P or
(5) Has been exposed by attending or working in a setting where there is a CONFIRMED DISEASE
OUTBREAK, or living in the same household as, and has knowledge about, an individual who
works or attends a setting where there is a CONFIRMED DISEASE OUTBREAK, or living in the same
household as, and has knowledge about, an individual diagnosed with an illness caused by:
(a) Norovirus within the past 48 hours of the last exposure, P
(b) SHIGA TOXIN-PRODUCING ESCHERICHIA COLI or Shigella spp. within the past 3 days of the last
exposure, P
(c) Salmonella Typhi within the past 14 days of the last exposure, P or
(d) Hepatitis A virus within the past 30 days of the last exposure, P
(B) The PERSON IN CHARGE shall notify the REGULATORY AUTHORITY when a FOOD EMPLOYEE is:
(1) Jaundiced, Pf or
(2) Diagnosed with an illness due to a pathogen as specified under subparagraphs (A)(2)(a)-(f) of
this section. Pf
(C) The PERSON IN CHARGE shall ensure that a CONDITIONAL EMPLOYEE:
(1) Who exhibits or reports a symptom, or who reports a diagnosed illness as specified under
Subparagraphs (A)(1)-(3) of this section, is prohibited from becoming a FOOD EMPLOYEE until
the CONDITIONAL EMPLOYEE meets the criteria for the specific symptoms or diagnosed illness as
specified under § 2-201.13, P and
(2) Who will work as a FOOD EMPLOYEE in a FOOD ESTABLISHMENT that serves as a HIGHLY SUSCEPTIBLE
POPULATION and reports a history of exposure as specified under Subparagraphs (A)(4)-(5), is
prohibited from becoming a FOOD EMPLOYEE until the CONDITIONAL EMPLOYEE meets the criteria as
specified under ¶ 2-201.13(l). P
(D) The PERSON IN CHARGE shall ensure that a FOOD EMPLOYEE who exhibits or reports a symptom, or who
reports a diagnosed illness or a history of exposure as specified under subparagraphs (A)(1)-(5) of
this section is:
34
(1) EXCLUDED as specified under ¶¶ 2-201.12 (A)-(C), and Subparagraphs (D)(1), (F)(1), (G) or
(H)(1) and in compliance with the provisions specified under ¶¶ 2-201.13 (A)-(H), P or
(2) RESTRICTED as specified under Subparagraphs ¶¶ 2-201.12 (D)(2), (E)(2), (F)(2)(H)(2) or ¶¶ 2-
201.12 (I) or (J) and in compliance with the provisions specified under ¶¶ 2-201.13 (D)-(J). P
(E) A FOOD EMPLOYEE or CONDITIONAL EMPLOYEE shall report to the PERSON IN CHARGE the information as
specified under ¶ (A) of this section. Pf
(F) A FOOD EMPLOYEE shall:
(1) Comply with an EXCLUSION as specified under ¶¶ 2-201.12 (A)-(C) and Subparagraphs 2-201.12
(D)(1), E(1), (F)(1), (G), or (H)(1) and with the provisions specified under ¶¶ 2-201.13 (A)-
(H), P or
(2) Comply with a RESTRICTION as specified under Subparagraphs 2-201.12 (D)(2), (E)(2), (F)(2),
(G), (H)(2) or ¶¶ 2-201.12(H), (I), or (J) and comply with the provisions specified under ¶¶ 2-
201.13 (D)-(J). P
2-201.12 EXCLUSIONS AND RESTRICTIONS
The PERSON IN CHARGE shall EXCLUDE or RESTRICT a FOOD EMPLOYEE from a FOOD ESTABLISHMENT in accordance with
the following:
(A) Except when the symptom is from a noninfectious condition, EXCLUDE a FOOD EMPLOYEE if the FOOD
EMPLOYEE is:
(1) Symptomatic with vomiting or diarrhea, P or
(2) Symptomatic with vomiting or diarrhea and diagnosed with an infection from Norovirus,
Shigella spp., nontyphoidal Salmonella, or SHIGA TOXIN-PRODUCING E. COLI. P
(B) EXCLUDE a FOOD EMPLOYEE who is:
(1) Jaundiced and the onset of jaundice occurred within the last 7 calendar days, unless the FOOD
EMPLOYEE provides to the PERSON IN CHARGE written medical documentation from a HEALTH
PRACTITIONER specifying that the jaundice is not caused by hepatitis A virus or other fecal-orally
transmitted infection, P
(2) Diagnosed with an infection from hepatitis A virus within 14 calendar days from the onset of
any illness symptoms, or within 7 calendar days of the onset of jaundice, P or
(3) Diagnosed with an infection from hepatitis A virus without developing more symptoms. P
(C) EXCLUDE a FOOD EMPLOYEE who is diagnosed with an infection from Salmonella Typhi, or reports a
previous infection with Salmonella Typhi within the past 3 months as specified under Subparagraph
2-201.11(A)(3). P
(D) If a FOOD EMPLOYEE is diagnosed with an infection from Norovirus and is ASYMPTOMATIC:
(1) EXCLUDE the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT serving a HIGHLY SUSCEPTIBLE
POPULATION, P or
(2) RESTRICT the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE
POPULATION. P
(E) If a FOOD EMPLOYEE is diagnosed with an infection from Shigella spp. and is ASYMPTOMATIC:
(1) EXCLUDE the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT serving HIGHLY SUSCEPTIBLE
POPULATION; P
(2) RESTRICT the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE
POPULATION. P
(F) If a FOOD EMPLOYEE is diagnosed with an infection from SHIGA TOXIN-PRODUCING E. COLI, and is
ASYMPTOMATIC:
(1) EXCLUDE the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT serving a HIGHLY SUSCEPTIBLE
POPULATION; P or
35
(2) RESTRICT the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE
POPULATION. P
(G) If a FOOD EMPLOYEE is diagnosed with an infection from nontyphoidal Salmonella and is ASYMPTOMATIC,
RESTRICT the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT serving a HIGH SUSCEPTIBLE POPULATION. P
(H) If a FOOD EMPLOYEE is ill with symptoms of acute onset of sore throat with fever:
(1) EXCLUDE the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT serving a HIGHLY SUSCEPTIBLE
POPULATION, P or
(2) RESTRICT the FOOD EMPLOYEE who works in a FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE
POPULATION. P
(I) If a FOOD EMPLOYEE is infected with a skin lesion containing pus such as a boil or infected wound that is
open or draining and not properly covered as specified under subparagraph 2-201.11(A)(1)(e).
RESTRICT the FOOD EMPLOYEE. P
(J) If a FOOD EMPLOYEE is exposed to a foodborne pathogen as specified under Subparagraphs 2-
201.11(A)(4)(a-d) or 2-201.11(A)(5)(a-d). RESTRICT the FOOD EMPLOYEE who works in a FOOD
ESTABLISHMENT serving a HIGHLY SUSCEPTIBLE POPULATION. P
2-201.13 REMOVAL, ADJUSTMENT, OR RETENTION OF EXCLUSIONS AND RESTRICTIONS
The PERSON IN CHARGE shall adhere to the following conditions with removing, adjusting, or retaining the
EXCLUSION or RESTRICTION of a FOOD EMPLOYEE:
(A) Except when a FOOD EMPLOYEE is diagnosed with an infection from hepatitis A virus or Salmonella Typhi:
(1) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under Subparagraph 2-201.12(A)(1)
if the FOOD EMPLOYEE:
(a) Is ASYMPTOMATIC for at least 24 hours, P or
(b) Provides to the PERSON IN CHARGE written medical documentation from a HEALTH
PRACTITIONER that states the symptom is from a noninfectious condition. P
(2) If a FOOD EMPLOYEE was diagnosed with an infection from Norovirus and EXCLUDED as specified
under Subparagraph 2-201-12(A)(2):
(a) RESTRICT the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours and works in a
FOOD ESTABLISHMENT not serving HIGHLY SUSCEPTIBLE POPULATION, until the conditions for
reinstatement as specified under Subparagraphs (D)(1) or (2) of this section are met; P
or
(b) Retain the EXCLUSION for the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours
and works in a FOOD ESTABLISHMENT that serves HIGHLY SUSCEPTIBLE POPULATION, until the
conditions for reinstatement as specified under Subparagraphs (D)(1) or (2) of this
section are met. P
(3) If a FOOD EMPLOYEE was diagnosed with an infection from Shigella spp. and EXCLUDED as specified
under Subparagraph 2-201.12(A)(2):
(a) RESTRICT the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours and works in a
FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE POPULATION, until the conditions for
reinstatement as specified under Subparagraphs (E)(1) or (2) of this section are met; P
or
(b) Retain the EXCLUSION for the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours
and works in a FOOD ESTABLISHMENT that serves a HIGHLY SUSCEPTIBLE POPULATION, until the
conditions for reinstatement as specified under Subparagraphs (E)(1) or (2), or (E)(1)
and (3)(a) of this section are met. P
(4) If a FOOD EMPLOYEE was diagnosed with an infection from SHIGA TOXIN-PRODUCING ESCHERICHIA COLI
and EXCLUDED as specified under Subparagraph 2-201.12(A)(2):
36
(a) RESTRICT the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours and works in a
FOOD ESTABLISHMENT not serving a HIGHLY SUSCEPTIBLE POPULATION, until the conditions for
reinstatement as specified under subparagraphs (F)(1) or (2) of this section are met; P
or
(b) Retain the EXCLUSION for the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 24 hours
and works in a FOOD ESTABLISHMENT that serves a HIGHLY SUSCEPTIBLE POPULATION, until the
conditions for reinstatement as specified under Subparagraphs (F)(1) or (2) are met. P
(5) If a FOOD EMPLOYEE was diagnosed with an infection from nontyphoidal Salmonella and EXCLUDED
as specified under Subparagraph 2-201.12(a)(2):
(a) RESTRICT the FOOD EMPLOYEE, who is ASYMPTOMATIC for at least 30 days until conditions for
reinstatement as specified under Subparagraphs (G)(1) or (2) of this section are met; P
or
(b) Retain the EXCLUSION for the FOOD EMPLOYEE who is SYMPTOMATIC, until conditions for
reinstatement as specified under Paragraphs (G)(1) or (G)(2) of this section are met. P
(B) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under ¶ 2-201.12(B) if the PERSON IN CHARGE
obtains APPROVAL from the REGULATORY AUTHORITY and one of the following conditions is met:
(1) The FOOD EMPLOYEE has been jaundiced for more than 7 calendar days. P
(2) The anicteric FOOD EMPLOYEE has been SYMPTOMATIC with symptoms other than jaundice for
more than 14 calendar days, P or
(3) The FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical documentation from a
HEALTH PRACTITIONER stating that the FOOD EMPLOYEE is free of a hepatitis A virus infection. P
(C) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under ¶ 2-201.12(C) if:
(1) The PERSON IN CHARGE obtains APPROVAL from the REGULATORY AUTHORITY; P and
(2) The FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical documentation from a
HEALTH PRACTITIONER that states the FOOD EMPLOYEE is free from S. Typhi infection. P
(D) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under Subparagraphs 2-201.12(A)(2) or
(D)(1) who was RESTRICTED under Subparagraph 2-201.12(D)(2) if the PERSON IN CHARGE obtains
APPROVAL from the REGULATORY AUTHORITY and one of the following conditions is met:
(1) The EXCLUDED or RESTRICTED FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical
documentation from a HEALTH PRACTITIONER stating that the FOOD EMPLOYEE is free of a Norovirus
infection. P
(2) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED after symptoms of vomiting or diarrhea
resolved, and more than 48 hours have passed since the FOOD EMPLOYEE became ASYMPTOMATIC; P
or
(3) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED and did not develop symptoms and more than
48 hours have passed since the FOOD EMPLOYEE was diagnosed. P
(E) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under Subparagraphs 2-201.12(A)(2) or
(E)(1) or who was RESTRICTED under Subparagraph 2-201.12(E)(2) if the PERSON IN CHARGE obtains
APPROVAL from the REGULATORY AUTHORITY and one of the following conditions is met:
(1) The EXCLUDED or RESTRICTED FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical
documentation from a HEALTH PRACTITIONER stating that the FOOD EMPLOYEE is free of a Shigella
spp. infection based on test results showing 2 consecutive negative stool specimen cultures
that are taken:
(a) Not earlier than 48 hours after discontinuance of antibiotics, P and
(b) At least 24 hours apart; P
37
(2) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED after symptoms of vomiting or diarrhea
resolved, and more than 7 calendar days have passed since the FOOD EMPLOYEE became
ASYMPTOMATIC, P or
(3) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED and did not develop symptoms and more than 7
calendar days have passed since the FOOD EMPLOYEE was diagnosed. P
(F) Reinstate a FOOD EMPLOYEE who was EXCLUDED or RESTRICTED as specified under Subparagraphs 2-
201.12(A)(2) or (F)(1) who was RESTRICTED under Subparagraph 2-201.12(F)(2) if the PERSON IN
CHARGE obtains APPROVAL from the REGULATORY AUTHORITY and one of the following conditions is met:
(1) The EXCLUDED or RESTRICTED FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical
documentation from a HEALTH PRACTITIONER stating that the FOOD EMPLOYEE is free of an infection
from SHIGA TOXIN-PRODUCING ESCHERICHIA COLI based on test results that show 2 consecutive
negative stool specimen cultures that are taken:
(a) Not earlier than 48 hours after discontinuance of antibiotics; P and
(b) At least 24 hours apart; P
(2) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED after symptoms of vomiting or diarrhea
resolved and more than 7 calendar days have passed since the FOOD EMPLOYEE became
ASYMPTOMATIC; P or
(3) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED and did not develop symptoms and more than 7
days have passed since the FOOD EMPLOYEE was diagnosed. P
(G) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under Subparagraph 2-201.12(A)(2) or who
was RESTRICTED as specified under ¶ 2-201.12(G) if the PERSON IN CHARGE obtains APPROVAL from the
REGULATORY AUTHORITY and one of the following conditions is met:
(1) The EXCLUDED or RESTRICTED FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical
documentation from a HEALTH PRACTITIONER stating that the FOOD EMPLOYEE is free of a
nontyphoidal Salmonella infection based on test results showing 2 consecutive negative stool
specimen cultures that are taken;
(a) Not earlier than 48 hours after discontinuance of antibiotics, P and
(b) At least 24 hours apart; P
(2) The FOOD EMPLOYEE was RESTRICTED after symptoms of vomiting or diarrhea resolved, and more
than 30 days have passed since the FOOD EMPLOYEE became ASYMPTOMATIC; P or
(3) The FOOD EMPLOYEE was EXCLUDED or RESTRICTED and did not develop symptoms and more than
30 days have passed since the FOOD EMPLOYEE was diagnosed. P
(H) Reinstate a FOOD EMPLOYEE who was EXCLUDED as specified under Subparagraph 2-201.12(H)(1) or (2)
if the FOOD EMPLOYEE provides to the PERSON IN CHARGE written medical documentation from a HEALTH
PRACTITIONER stating that the FOOD EMPLOYEE meets one of the following conditions:
(1) Has received antibiotic therapy for Streptococcus pyogenes infection for more than 24 hours; P
(2) Has at least one negative throat specimen culture for Streptococcus pyogenes infection; P or
(3) Is otherwise determined by a HEALTH PRACTITIONER to be free of a Streptococcus pyogenes
infection. P
(I) Reinstate a FOOD EMPLOYEE who was RESTRICTED as specified under ¶ 2-201.12(I) if the skin, infected
wound, cut, or pustular boil is properly covered with one of the following:
(1) An impermeable cover such as a finger cot or stall and a SINGLE-USE glove over the impermeable
cover if the infected wound or pustular boil is on the hand, finger, or wrist; P
(2) An impermeable cover on the arm if the infected wound or pustular boil is on the arm; P or
(3) A dry, durable, tight-fitting bandage if the infected wound or pustular boil is on another part of
the body. P
38
(J) Reinstate a FOOD EMPLOYEE who was RESTRICTED as specified under ¶ 2-201.12(J) and was exposed to
one of the following pathogens as specified under Subparagraphs 2-201.11(A)(4)(a-d) or 2-
201.11(A)(5)(a-d):
(1) Norovirus and one of the following conditions is met:
(a) More than 48 hours have passed since the last day the FOOD EMPLOYEE was potentially
exposed; P or
(b) More than 48 hours have passed since the FOOD EMPLOYEE'S household contact became
ASYMPTOMATIC. P
(2) Shigella spp. or SHIGA TOXIN-PRODUCING ESCHERICHIA COLI and one of the following conditions is
met:
(a) More than 3 calendar days have passed since the last day the FOOD EMPLOYEE was
potentially exposed; P or
(b) More than 3 calendar days have passed since the FOOD EMPLOYEE’S household contact
became ASYMPTOMATIC. P
(3) S. Typhi and one of the following conditions is met:
(a) More than 14 calendar days have passed since the last day the FOOD EMPLOYEE was
potentially exposed; P or
(b) More than 14 calendar days have passed since the FOOD EMPLOYEE’S household contact
became ASYMPTOMATIC. P
(4) Hepatitis A virus and one of the following conditions is met:
(a) The FOOD EMPLOYEE is immune to hepatitis A virus infection because of a prior illness
from hepatitis A; P
(b) The FOOD EMPLOYEE is immune to hepatitis A virus infection because of vaccination
against hepatitis A; P
(c) The FOOD EMPLOYEE is immune to hepatitis A virus infection because of IgG
administration; P
(d) More than 30 calendar days have passed since the last day the FOOD EMPLOYEE was
potentially exposed; P
(e) More than 30 calendar days have passed since the FOOD EMPLOYEE’S household contact
became jaundiced; P or
(f) The FOOD EMPLOYEE does not use an alternative procedure that allows bare hand contact
with READY-TO-EAT FOOD until at least 30 days after the potential exposure, as specified in
Subparagraphs (J)(4)(d) and (e) of this section, and the FOOD EMPLOYEE receives
additional training about:
(i.) Hepatitis A symptoms and preventing the transmission of infection, P
(ii.) Proper handwashing procedures, P and
(iii.) Protecting READY-TO-EAT FOOD from contamination introduced by bare hand
contact. P
39
2-3 PERSONAL CLEANLINESS
SUBPARTS 2-301 Hands and Arms
2-302 Fingernails
2-303 Jewelry
2-304 Outer Clothing
HANDS AND ARMS
2-301.11 CLEAN CONDITION
FOOD EMPLOYEES shall keep their hands and exposed portions of their arms clean. P
2-301.12 CLEANING PROCEDURE
(A) Except as specified in ¶ (D) of this section, FOOD EMPLOYEES shall clean their hands and exposed
portions of their arms, including surrogate prosthetic devices for hands or arms for at least 20
seconds, using a cleaning compound in a HANDWASHING SINK that is equipped as specified under § 5-
202.12 and Subpart 6-301. P
(B) FOOD EMPLOYEES shall use the following cleaning procedure in the order stated to clean their hands and
exposed portions of their arms, including surrogate prosthetic devices for hands and arms:
(1) Rinse under clean, running warm water; P
(2) Apply an amount of cleaning compound recommended by the cleaning compound
manufacturer; P
(3) Rub together vigorously for at least 10 to 15 seconds while:
(a) Paying particular attention to removing soil from underneath the fingernails during the
cleaning procedure, P and
(b) Creating friction on the surfaces of the hands and arms or surrogate prosthetic devices
for hands and arms, finger tips, and areas between the fingers;
(4) Thoroughly rinse under clean, running warm water; P and
(5) Immediately follow the cleaning procedure with thorough drying using a method as specified
under § 6-301.12 P
(C) To avoid re-contaminating their hands or surrogate prosthetic devices, FOOD EMPLOYEES may use
disposable paper towels or similar clean barriers when touching surfaces such as manually operated
faucet handles on a HANDWASHING SINK or the handle of a restroom door.
(D) If APPROVED and capable of removing the types of soils encountered in the FOOD operations involved, an
automatic handwashing facility may be used by FOOD EMPLOYEES to clean their hands or surrogate
prosthetic devices.
2-301.13 SPECIAL HANDWASH PROCEDURES
Reserved.
2-301.14 WHEN TO WASH
FOOD EMPLOYEES shall clean their hands and exposed portions of their arms as specified under § 2-301.12
immediately before engaging in FOOD preparation including working with exposed FOOD, clean EQUIPMENT and
UTENSILS, and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES P and:
(A) After touching bare human body parts other than clean hands and clean, exposed portions of arms; P
(B) After using the toilet room; P
(C) After caring for or handling SERVICE ANIMALS or aquatic animals as specified in ¶ 2-403.11 (B); P
(D) Except as specified in ¶ 2-401.11(B), after coughing, sneezing, using a handkerchief or disposable
tissue, using tobacco, eating, or drinking; P
40
(E) After handling soiled EQUIPMENT or UTENSILS; P
(F) During FOOD preparation, as often as necessary to remove soil and contamination and to prevent cross
contamination when changing tasks; P
(G) When a switching between working with raw FOOD and working with READY-TO-EAT FOOD; P
(H) Before donning gloves to initiate a task that involves working with FOOD; P and
(I) After engaging in other activities that contaminate the hands. P
2-301.15 WHERE TO WASH
FOOD EMPLOYEES shall clean their hands in a HANDWASHING SINK or APPROVED automatic handwashing facility
and may not clean their hands in a sink used for FOOD preparation or WAREWASHING, or in a service sink or a
curbed cleaning facility used for the disposal of mop water and similar liquid waste. Pf
2-301.16 HAND ANTISEPTICS
(A) A hand antiseptic used as a topical application, a hand antiseptic solution used as a hand dip, or a
hand antiseptic soap shall:
(1) Comply with one of the following:
(a) Be an APPROVED drug that is listed in the FDA publication Approved Drug Products
with Therapeutic Equivalence Evaluations as an APPROVED drug based on safety and
effectiveness; Pf or
(b) Have active antimicrobial ingredients that are listed in the FDA monograph for OTC
Health-Care Antiseptic Drug Products as an antiseptic handwash, Pf and
(2) Consist only of components which the intended use of each complies with one of the following:
(a) A threshold of regulation exemption under 21 CFR 170.39 - Threshold of regulation for
substances used in FOOD-contact articles; Pf or
(b) 21 CFR 178 - Indirect FOOD ADDITIVES: Adjuvants, Production Aids, and Sanitizers as
regulated for use as a FOOD ADDITIVE with conditions of safe use, Pf or
(c) A determination of generally recognized as safe (GRAS). Partial listings of substances
with FOOD uses that are GRAS may be found in 21 CFR 182 - Substances General
Recognized as Safe, 21 CFR 184 - Direct FOOD Substances Affirmed as Generally
Recognized as Safe, or 21 CFR 186 - Indirect FOOD Substances Affirmed as Generally
Recognized as Safe for use in contact with FOOD, and in FDA's Inventory of GRAS Notices,
Pf or
(d) A prior sanction listed under 21 CFR 181 - Prior Sanctioned FOOD Ingredients, Pf or
(e) A FOOD Contact Notification that is effective, Pf and
(3) Be applied only to hands that are cleaned as specified under § 2-301.12
(B) If a hand antiseptic or a hand antiseptic solution used as a hand dip does not meet the criteria
specified under Subparagraph (A)(2) of this section, use shall be:
(1) Followed by thorough hand rinsing in clean water before hand contact with FOOD or by the use
of gloves, Pf or
(2) Limited to situations that involve no direct contact with FOOD by the bare hands Pf
(C) A hand antiseptic solution used as a hand dip shall be maintained clean and at a strength equivalent to
at least 100 MG/L chlorine. Pf
41
FINGERNAILS
2-302.11 MAINTENANCE
(A) FOOD EMPLOYEES shall keep their fingernails trimmed, filed, and maintained so the edges and surfaces
are cleanable and not rough. Pf
(B) Unless wearing intact gloves in good repair, a FOOD EMPLOYEE may not wear fingernail polish or artificial
fingernails when working with exposed FOOD. Pf
JEWELRY
2-303.11 PROHIBITION
Except for a plain ring such as a wedding band, while preparing FOOD, FOOD EMPLOYEES may not wear jewelry
including medical information jewelry on their arms and hands.
OUTER CLOTHING
2-304.11 CLEAN CONDITION
FOOD EMPLOYEES shall wear clean outer clothing to prevent contamination of FOOD, EQUIPMENT, UTENSILS, LINENS,
and SINGLE-SERVICE and SINGLE-USE ARTICLES.
2-4 HYGIENIC PRACTICES
SUBPARTS 2-401 Food Contamination Prevention
2-402 Hair Restraints
2-403 Animals
FOOD CONTAMINATION PREVENTION
2-401.11 EATING, DRINKING, OR USING TOBACCO
(A) Except as specified in ¶ (B) of this section, an EMPLOYEE shall eat, drink, or use any form of tobacco
only in designated areas where the contamination of exposed FOOD; CLEAN EQUIPMENT, UTENSILS, and
LINENS; unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES; or other items needing protection cannot
result.
(B) A FOOD EMPLOYEE may drink from a closed BEVERAGE container if the container is handled to prevent
contamination of:
(1) The EMPLOYEE's hands;
(2) The container; and
(3) Exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-USE
ARTICLES.
2-401.12 DISCHARGES FROM THE EYES, NOSE AND MOUTH
FOOD EMPLOYEES experiencing persistent sneezing, coughing or a runny nose that causes discharges from the
eyes, nose, or mouth may not work with exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped
SINGLE-SERVICE or SINGLE-USE ARTICLES.
42
HAIR RESTRAINTS
2-402.11 EFFECTIVENESS
(A) Except as specified in ¶ (B) of this section, FOOD EMPLOYEES shall wear hair restraints such as hats, hair
covering or nets, beard restraints, and clothing that covers body hair, that are designed and worn to
effectively keep their hair from contacting exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and
unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES.
(B) This section does not apply to FOOD EMPLOYEES such as counter staff who only serve BEVERAGES and
wrapped or PACKAGED FOODS, hostesses, and wait staff if they present a minimal RISK of contaminating
exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-USE
ARTICLES.
2-403.11 HANDLING PROHIBITION
(A) Except as specified in ¶ (B) of this section, FOOD EMPLOYEES may not care for or handle animals that
may be present such as patrol dogs, SERVICE ANIMALS, or pets that are allowed as specified in
Subparagraphs 6-501.115(B)(2)-(5). Pf
(B) FOOD EMPLOYEES with SERVICE ANIMALS may handle or care for their SERVICE ANIMALS and FOOD EMPLOYEES
may handle or care for FISH in aquariums or MOLLUSCAN SHELLFISH or crustacea in display tanks if they
wash their hands as specified under § 2-301.12 and ¶ 2-301.14(C).
2-5 RESPONDING TO CONTAMINATION EVENTS
SUBPART 2-01 Procedures for Responding
2-501.11 CLEAN-UP OF VOMITING AND DIARRHEAL EVENTS
A FOOD ESTABLISHMENT shall have procedures for EMPLOYEES to follow when responding to vomiting or
diarrheal events that involve the discharge of vomitus or fecal matter onto surfaces in the FOOD
ESTABLISHMENT. The procedures shall address the specific actions EMPLOYEES must take to minimize the
spread of contamination and the exposure of EMPLOYEES, CONSUMERS, FOOD, and surfaces to vomitus or fecal
matter. Pf
43
CHAPTER 3 – FOOD
3-1 CHARACTERISTICS
3-2 SOURCES, SPECIFICATIONS, AND ORIGINAL CONTAINERS AND RECORDS
3-3 PROTECTION FROM CONTAMINATION AFTER RECEIVING
3-4 DESTRUCTION OF ORGANISIMS OF PUBLIC HEALTH CONCERN
3-5 LIMITATION OF GROWTH OF ORGANISMS OF PUBLIC HEALTH CONCERN
3-6 FOOD IDENTITY, PRESENTATION, AND ON-PREMISES LABELING
3-7 CONTAMINATED FOOD
3-8 SPECIAL REQUIREMENTS FOR HIGHLY SUSCEPTIBLE POPULATIONS
3-1 CHARACTERISTICS
SUBPART 3-101 Condition
CONDITION
3-101.11 SAFE, UNADULTERATED, AND HONESTLY PRESENTED
FOOD shall be safe, UNADULTERATED, and, as specified under § 3-601.12, honestly presented. P
3-2 SOURCES, SPECIFICATIONS AND ORIGINAL CONTAINERS AND RECORDS
SUBPARTS 3-201 Sources
3-202 Specifications for Receiving
3-203 Original Containers and Records
SOURCES
3-201.11 COMPLIANCE WITH FOOD LAW
(A) FOOD shall be obtained from sources that comply with LAW. P
(B) FOOD prepared in a private home may not be used or offered for human consumption in a FOOD
ESTABLISHMENT. P
(C) PACKAGED FOOD shall be labeled as specified in LAW, including 21 CFR 101 FOOD Labeling, 9 CFR 317
Labeling, Marking Devices, and Containers, and 9 CFR 381 Subpart N Labeling and Containers, and as
specified under §§ 3-202.17 and 3-202.18. Pf
(D) FISH, other than those specified in paragraph 3-402.11(B), that are intended for consumption in raw or
undercooked form and allowed as specified in paragraph 3-401.11(D), may be offered for sale or service
if they are obtained from a supplier that freezes the FISH as specified under § 3-402.11; or if they are
frozen on the PREMISES as specified under § 3-402.11 and records are retained as specified under § 3-
402.12.
IDAPA 16.02.19.320 - MEAT AND POULTRY
01. Custom MEAT. MEAT that is processed for individual owner(s) by a custom butcher, under the
custom exemption to 9 CFR 303.1 "Mandatory MEAT Inspection Exemptions", must be marked "Not
for Sale" and may not be sold or served or given away to any member of the public. This MEAT must
be for the use in the household of such owner(s), their families, nonpaying guests and EMPLOYEES
only. P
02. POULTRY Exemption. POULTRY that is exempt in 9 CFR 381.10, Subpart C "Mandatory POULTRY
Products Inspection Exemptions" may be sold, served or given away in Idaho if it is processed in a
LICENSED FOOD processing facility and is labeled "Exempt from USDA Inspection per PL 492". P
(E) WHOLE-MUSCLE, INTACT BEEF steaks that are intended for consumption in an undercooked form without
a CONSUMER advisory as specified in ¶ 3-401.11(C) shall be:
44
(1) Obtained from a FOOD PROCESSING PLANT that, upon request by the purchaser, packages the steaks
and labels them, to indicated that the steaks meet the definition of WHOLE-MUSCLE, INTACT BEEF, Pf
or
(2) Deemed acceptable by the REGULATORY AUTHORITY based on other evidence, such as written
buyer specifications or invoices, that indicates that the steaks meet the definition of WHOLE-
MUSCLE, INTACT BEEF, and
(3) If individually cut in a FOOD ESTABLISHMENT:
(a) Cut from WHOLE-MUSCLE, INTACT BEEF that is labeled by a FOOD PROCESSING PLANT as
specified in Subparagraph(E)(1) of this section or identified as specified in
Subparagraph (E)(2) of this section, Pf
(b) Prepared so they remain intact, Pf and
(c) If PACKAGED for undercooking in a FOOD ESTABLISHMENT, labeled as specified in
Subparagraph (E)(1) of this section or identified as specified in (E)(2) of this section. Pf
(F) MEAT and POULTRY that is not a READY-TO-EAT FOOD and is in a PACKAGED form when it is offered for sale
or otherwise offered for consumption, shall be labeled to include safe handling instructions as
specified in LAW, including 9 CFR 317.2(I) and 9 CFR 381.125(b).
(G) EGGS that have not been specifically treated to destroy all viable Salmonellae shall be labeled to
include safe handling instructions as specified in LAW, including 21 CFR 101.17(h).
3-201.12 FOOD IN HERMETICALLY SEALED CONTAINER
FOOD in a HERMETICALLY SEALED CONTAINER shall be obtained from a FOOD PROCESSING PLANT that is regulated by
the FOOD regulatory agency that has jurisdiction over the plant. P
3-201.13 FLUID MILK AND MILK PRODUCTS
Fluid milk and milk products shall be obtained from sources that comply with GRADE A STANDARDS as
specified in LAW. P
3-201.14 FISH
(A) FISH that are received for sale or service shall be:
(1) Commercially and legally caught or harvested; P or
(2) APPROVED for sale or service. P
(B) MOLLUSCAN SHELLFISH that are recreationally caught may not be received for sale or service. P
3-201.15 MOLLUSCAN SHELLFISH
(A) MOLLUSCAN SHELLFISH shall be obtained from sources according to LAW and the requirements specified
in the U.S. Department of Health and Human Services, Public Health Service, FOOD and Drug
Administration, National Shellfish Sanitation Program Guide for the Control of MOLLUSCAN SHELLFISH. P
(B) MOLLUSCAN SHELLFISH received in interstate commerce shall be from sources that are listed in the
Interstate Certified Shellfish Shippers List. P
3-201.16 WILD MUSHROOMS
(A) Except as specified in ¶ (B) of this section, mushroom species picked in the wild shall not be offered
for sale or service by a FOOD ESTABLISHMENT unless the FOOD ESTABLISHMENT has been APPROVED to do so. P
(B) This section does not apply to:
(1) Cultivated wild mushroom species that are grown, harvested, and processed in an operation that
is regulated by the FOOD regulatory agency that has jurisdiction over the operation; or
(2) Wild mushroom species if they are in PACKAGED form and are the product of a FOOD PROCESSING
PLANT that is regulated by the FOOD regulatory agency that has jurisdiction over the plant.
45
3-201.17 GAME ANIMALS
(A) If GAME ANIMALS are received for sale or service they shall be:
(1) Commercially raised for FOOD P and:
(a) Raised, slaughtered, and processed under a voluntary inspection program that is
conducted by the agency that has animal health jurisdiction, P or
(b) Under a routine inspection program conducted by a regulatory agency other than the
agency that has animal health jurisdiction, P and
(c) Raised, slaughtered, and processed according to:
(i.) LAWS governing MEAT and POULTRY as determined by the agency that has animal
health jurisdiction and the agency that conducts the inspection program, P and
(ii.) Requirements which are developed by the agency that has animal health
jurisdiction and the agency that conducts the inspection program with
consideration of factors such as the need for antemortem and postmortem
examination by an APPROVED veterinarian or veterinarian's designee, P
(2) Under a voluntary inspection program administered by the USDA for GAME ANIMALS such as
exotic animals (reindeer, elk, deer, antelope, water buffalo, or bison) that are "inspected and
APPROVED" in accordance with 9 CFR 352 Exotic animals; voluntary inspection or rabbits that
are "inspected and certified" in accordance with 9 CFR 354 voluntary inspection of rabbits and
edible products thereof; P
(3) As allowed by LAW, for wild GAME ANIMALS that are live-caught:
(a) Under a routine inspection program conducted by a regulatory agency such as the
agency that has animal health jurisdiction, P and
(b) Slaughtered and processed according to:
(i.) LAWS governing MEAT and POULTRY as determined by the agency that has animal
health jurisdiction and the agency that conducts the inspection program, P and
(ii.) Requirements which are developed by the agency that has animal health
jurisdiction and the agency that conducts the inspection program with
consideration of factors such as the need for antemortem and postmortem
examination by an APPROVED veterinarian or veterinarian's designee. P
IDAPA 16.02.19.325 – GAME ANIMALS
Modification to 3-201.17(A)(4), is made by deleting section 3-201.17(A)(4), and replacing it with
Subsections 325.01 through 325.04.
01. Field Dressed GAME ANIMALS. Uninspected wild GAME ANIMALS and wild POULTRY may be custom
processed or prepared and served upon request by an individual having ownership of the animal.
Except as allowed in Subsection 325.04 of this rule, uninspected wild game animals and wild poultry
must be processed for or served to that owner and for the family or guests of that individual animal
owner only. P
02. Processing GAME ANIMALS. GAME ANIMALS and birds are to be completely separated from other FOOD
during storage, processing, preparation and service with the use of separate EQUIPMENT or areas or
by scheduling and cleaning, providing there is compliance with the following:
(a) Slaughtering and cleaning of GAME ANIMALS or birds cannot be done in the FOOD ESTABLISHMENT,
except for MEAT PROCESSING ESTABLISHMENTS with kill floors; P and
(b) GAME ANIMAL and other animal carcasses are free of any visible dirt, filth, fecal matter or hair
before such carcasses enter the FOOD ESTABLISHMENT, except for MEAT PROCESSING ESTABLISHMENTS
with kill floors; P and
(c) An identifying tag with the owner's name must be on each carcass or divided parts and
PACKAGED or wrapped parts, Pf and
46
(d) Each carcass or divided parts and PACKAGED or wrapped parts are marked or tagged with a "not
for sale" label. Except as allowed in Subsection 325.04 of this rule, these animals may not be
sold, given away, or served to any members of the public. Pf
03. Uninspected GAME ANIMALS. Any uninspected GAME ANIMALS prepared and served in a FOOD
ESTABLISHMENT may only be prepared and served at the request of the owner of the animals for the
owner and invited family or friends at a private dinner. Except as allowed in Subsection 325.04 of
this rule, these animals may not be served, sold or given away to any members of the public. P
04. Donated Game Meat. Legally harvested game meat may be donated to a food bank or food pantry
when the following conditions are met:
(a) The end recipient of the donated game meat signs an acknowledgement statement indicating
that he is aware that the meat has been donated and that the meat itself is uninspected, wild
harvested game meat. Pf
(b) The game meat must have been processed by:
i.) A facility that is subject to inspection by the regulatory authority with jurisdiction over
meat products. P
ii.) The facility packages the game meat into portions that require no further processing or
cutting by the food bank or food pantry; P and
(c) The meat is labeled by the processor with the following:
i.) Species identification; Pf
ii.) The name and address of the meat processing facility; Pf and
iii.) The words “Processed for Donation or Private Use” and “Cook to 165°F.” Pf
(B) A GAME ANIMAL may not be received for sale or service if it is a species of wildlife that is listed in 50 CFR
17 Endangered and threatened wildlife and plants.
SPECIFICATIONS FOR RECEIVING
3-202.11 TEMPERATURE
(A) Except as specified in ¶ (B) of this section, refrigerated, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD
shall be at a temperature of 5°C (41°F) or below when received. P
(B) If a temperature other than 5°C (41°F) for A TIME/TEMPERATURE CONTROL FOR SAFETY FOOD is specified in LAW
governing its distribution, such as LAWS governing milk and MOLLUSCAN SHELLFISH, the FOOD may be
received at the specified temperature.
(C) Raw EGGS shall be received in refrigerated EQUIPMENT that maintains an ambient air temperature of 7°C
(45°F) or less. P
(D) TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is cooked to a temperature and for a time specified
under §§ 3-401.11 - 3-401.13 and received hot shall be at a temperature of 57°C (135°F) or above. P
(E) A FOOD that is labeled frozen and shipped frozen by a FOOD PROCESSING PLANT shall be received frozen. Pf
(F) Upon receipt, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall be free of evidence of previous
temperature abuse. Pf
3-202.12 ADDITIVES
FOOD may not contain unAPPROVED FOOD ADDITIVES or ADDITIVES that exceed amounts specified in 21 CFR 170-
180 relating to FOOD ADDITIVES, generally recognized as safe or prior sanctioned substances that exceed
amounts specified in 21 CFR 181-186, substances that exceed amounts specified in 9 CFR Subpart C Section
424.21(b) Food ingredients and sources of radiation, or pesticide residues that exceed provisions specified
in 40 CFR 180 Tolerances for pesticides chemical in FOOD, and exceptions. P
47
3-202.13 EGGS
EGGS shall be received clean and sound and may not exceed the restricted EGG tolerances for U.S. CONSUMER
Grade B as specified in United States Standards, Grades, and Weight Classes for Shell EGGS, AMS 56.200 et
seq., administered by the Agricultural Marketing Service of USDA. P
3-202.14 EGGS AND MILK PRODUCTS, PASTEURIZED
(A) EGG PRODUCTS shall be obtained pasteurized. P
(B) Fluid and dry milk and milk products shall:
(1) Be obtained pasteurized; P and
(2) Comply with GRADE A STANDARDS as specified in LAW. P
(C) Frozen milk products, such as ice cream, shall be obtained pasteurized as specified in 21 CFR 135 -
Frozen desserts. P
(D) Cheese shall be obtained pasteurized unless alternative procedures to pasteurization are specified in
the CFR, such as 21 CFR 133 - Cheeses and related cheese products, for curing certain cheese varieties. P
3-202.15 PACKAGE INTEGRITY
FOOD packages shall be in good condition and protect the integrity of the contents so that the FOOD is not
exposed to ADULTERATION or potential contaminants. Pf
3-202.16 ICE
Ice for use as a FOOD or a cooling medium shall be made from DRINKING WATER. P
3-202.17 SHUCKED SHELLFISH, PACKING AND IDENTIFICATION
(A) Raw SHUCKED SHELLFISH shall be obtained in nonreturnable packages which bear a legible label that
identifies the: Pf
(1) Name, address, and CERTIFICATION NUMBER of the shucker, packer or repacker of the MOLLUSCAN
SHELLFISH, and Pf
(2) The "sell by" or "best if used by" date for packages with a capacity of less than 1.89 L (one-half
gallon) or the date shucked for packages with a capacity of 1.89 L (one-half gallon) or more. Pf
(B) A package of raw SHUCKED SHELLFISH that does not bear a label or which bears a label which does not
contain all the information as specified under ¶ (A) of this section shall be subject to a hold order, as
allowed by LAW, or seizure and destruction in accordance with 21 CFR Subpart D - Specific
Administrative Decisions Regarding Interstate Shipments, Section 1240.60(d) MOLLUSCAN SHELLFISH.
3-202.18 SHELLSTOCK IDENTIFICATION
(A) SHELLSTOCK shall be obtained in containers bearing legible source identification tags or labels that are
affixed by the harvester or DEALER that depurates, ships, or reships the SHELLSTOCK, as specified in the
National Shellfish Sanitation Program Guide for the control of MOLLUSCAN SHELLFISH, and that list: Pf
(1) Except as specified under ¶ (C) of this section, on the harvester's tag or label, the following
information in the following order. Pf
(a) The harvester's identification number that is assigned by the SHELLFISH CONTROL
AUTHORITY, Pf
(b) The date of harvesting, Pf
(c) The most precise identification of the harvest location or aquaculture site that is
practicable based on the system or harvest area designation that is in use by the
SHELLFISH CONTROL AUTHORITY and including the abbreviation of the name of the state or
country in which the shellfish are harvested, Pf
(d) The type and quantity of shellfish, Pf and
(e) The following statement in bold, capitalized type: "This tag is required to be attached
until container is empty or retagged and thereafter kept on file for 90 days", Pf and
48
(2) Except as specified in ¶ (D) of this section, on each DEALER'S tag or label, the following
information in the following order: Pf
(a) The DEALER'S name and address, and the CERTIFICATION NUMBER assigned by the SHELLFISH
CONTROL AUTHORITY, Pf
(b) The original shipper's CERTIFICATION NUMBER including the abbreviation of the name of
the state or country in which the shellfish are harvested, Pf
(c) The same information as specified for a harvester's tag under Subparagraphs (A)(1)(b)-
(d) of this section, Pf and
(d) The following statement in bold, capitalized type: "This tag is required to be attached
until container is empty and thereafter kept on file for 90 days." Pf
(B) A container of SHELLSTOCK that does not bear a tag or label or that bears a tag or label that does not
contain all the information as specified under ¶ (A) of this section shall be subject to a hold order, as
allowed by LAW, or seizure and destruction in accordance with 21 CFR Subpart D - Specific
Administrative Decisions Regarding Interstate Shipments, Section 1240.60(d)
(C) If a place is provided on the harvester's tag or label for a DEALER'S name, address, and CERTIFICATION
NUMBER, the DEALER'S information shall be listed first.
(D) If the harvester's tag or label is designed to accommodate each DEALER'S identification as specified under
Subparagraphs (A)(2)(a) and (b) of this section, individual DEALER tags or labels need not be provided.
3-202.19 SHELLSTOCK, CONDITION
When received by a FOOD ESTABLISHMENT, SHELLSTOCK shall be reasonably free of mud, dead shellfish, and
shellfish with broken shells. Dead shellfish or SHELLSTOCK with badly broken shells shall be discarded.
3-202.110 JUICE TREATED
Pre-PACKAGED JUICE shall:
(A) Be obtained from a processor with a HACCP system as specified in 21 CFR Part 120 HAZARD Analysis
and Critical Control (HACCP) Systems; Pf and
(B) Be obtained pasteurized or otherwise treated to attain a 5-log reduction of the most resistant
microorganism of public health significance as specified in 21 CFR Part 120.24 Process Controls. P
ORIGINAL CONTAINERS AND RECORDS
3-203.11 MOLLUSCAN SHELLFISH, ORIGINAL CONTAINER
(A) Except as specified in ¶¶ (B) - (D) of this section, MOLLUSCAN SHELLFISH may not be removed from the
container in which they are received other than immediately before sale or preparation for service.
(B) For display purposes, SHELLSTOCK may be removed from the container in which they are received,
displayed on drained ice, or held in a display container, and a quantity specified by a CONSUMER may be
removed from the display or display container and provided to the CONSUMER if:
(1) The source of the SHELLSTOCK on display is identified as specified under § 3-202.18 and recorded as
specified under § 3-203.12; and
(2) The SHELLSTOCK are protected from contamination.
(C) SHUCKED SHELLFISH may be removed from the container in which they were received and held in a display
container from which individual servings are dispensed upon a CONSUMER'S request if:
(1) The labeling information for the shellfish on display as specified under § 3-202.17 is retained and
correlated to the date when, or dates during which, the shellfish are sold or served; and
(2) The shellfish are protected from contamination.
(D) SHUCKED SHELLFISH may be removed from the container in which they were received and repacked in
CONSUMER self-service containers where allowed by LAW if:
49
(1) The labeling information for the shellfish is on each CONSUMER self-service container as specified
under § 3-202.17 and ¶¶ 3-602.11(A) and (B)(1)-(5);
(2) The labeling information as specified under § 3-202.17 is retained and correlated with the date
when, or dates during which, the shellfish are sold or served;
(3) The labeling information and dates specified under Subparagraph (D)(2) of this section are
maintained for 90 days; and
(4) The shellfish are protected from contamination.
3-203.12 SHELLSTOCK, MAINTAINING IDENTIFICATION
(A) Except as specified under Subparagraph (C)(2) of this section, SHELLSTOCK tags or labels shall remain
attached to the container in which the SHELLSTOCK are received until the container is empty. Pf
(B) The date when the last SHELLSTOCK from the container is sold or served shall be recorded on the tag or
label. Pf
(C) The identity of the source of SHELLSTOCK that are sold or served shall be maintained by returning
SHELLSTOCK tags or labels for 90 calendar days from the date that is recorded on the tag or label, as
specified under ¶ (B) of this section, by: Pf
(1) Using an APPROVED record keeping system that keeps the tags or labels in chronological order
correlated to the date that is recorded on the tag or label, as specified under ¶ (B) of this
section; Pf and
(2) If SHELLSTOCK are removed from its tagged or labeled container:
(a) Preserving source identification by using a record keeping system as specified under
Subparagraph (C)(1) of this section, Pf and
(b) Ensuring that SHELLSTOCK from one tagged or labeled container are not COMMINGLED with
SHELLSTOCK from another container with different CERTIFICATION NUMBERS; different
harvest dates; or different growing areas as identified on the tag or label before being
ordered by the CONSUMER. Pf
3-3 PROTECTION FROM CONTAMINATION AFTER RECEIVING
SUBPARTS 3-301 Preventing Contamination by Employees
3-302 Preventing Food and Ingredient Contamination
3-303 Preventing Contamination from Ice Used as a Coolant
3-304 Preventing Contamination from Equipment, Utensils, & Linens
3-305 Preventing Contamination from the Premises
3-306 Preventing Contamination from Consumers
3-307 Preventing Contamination from Other Sources
PREVENTING CONTAMINATION BY EMPLOYEES
3-301.11 PREVENTING CONTAMINATION FROM HANDS
(A) FOOD EMPLOYEES shall wash their hands as specified under § 2-301.12.
(B) Except when washing fruits and vegetables as specified under § 3-302.15 or as specified in ¶¶ (D) and (E)
of this section, FOOD EMPLOYEES may not contact exposed, READY-TO-EAT FOOD with their bare hands and
shall use suitable UTENSILS such as deli tissue, spatulas, tongs, SINGLE-USE gloves, or dispensing
EQUIPMENT. P
(C) FOOD EMPLOYEES shall minimize bare hand and arm contact with exposed FOOD that is not in a READY-TO-
EAT form. Pf
(D) Paragraph (B) of this section does not apply to a FOOD EMPLOYEE that contacts exposed, READY-TO-EAT FOOD
with bare hands at the time the READY-TO-EAT FOOD is being added as an ingredient to a FOOD that:
50
(1) Contains a raw animal FOOD and is to be cooked in the FOOD ESTABLISHMENT to heat all parts of the
FOOD to the minimum temperatures specified in ¶¶ 3-401.11(A)-(B) or § 3-401.12; or
(2) Does not contain a raw animal FOOD but is to be cooked in the FOOD ESTABLISHMENT to heat all parts
of the FOOD to a temperature of at least 63°C (145°F).
(E) FOOD EMPLOYEES not serving a HIGHLY SUSCEPTIBLE POPULATION may contact exposed, READY-TO-EAT FOOD with
their bare hands if:
(1) The PERMIT HOLDER obtains prior APPROVAL from the REGULATORY AUTHORITY;
(2) Written procedures are maintained in the FOOD ESTABLISHMENT and made available to the
REGULATORY AUTHORITY upon request that include:
(a) For each bare hand contact procedure, a listing of the specific READY-TO-EAT FOODS that are
touched by bare hands,
(b) Diagrams and other information showing that handwashing facilities, installed, located,
equipped, and maintained as specified under §§ 5-203.11, 5-204.11, 5-205.11, 6-301.11, 6-
301.12, and 6-301.14, are in an easily accessible location and in close proximity to the work
station where the bare hand contact procedure is conducted;
(3) A written EMPLOYEE health policy that details how the FOOD ESTABLISHMENT complies with §§ 2-
201.11, 2-201.12, and 2-201.13 including:
(a) Documentation that FOOD EMPLOYEES and CONDITIONAL EMPLOYEES acknowledge that they are
informed to report information about their health and activities as they relate to
gastrointestinal symptoms and diseases that are transmittable through FOOD as specified
under ¶ 2-201.11(A),
(b) Documentation that FOOD EMPLOYEES and CONDITIONAL EMPLOYEES acknowledge their
responsibilities as specified under ¶ 2-201.11(E) and (F), and
(c) Documentation that the PERSON IN CHARGE acknowledges the responsibilities as specified
under ¶¶ 2-201.11(B), (C) and (D) and §§ 2-201.12 and 2-201.13;
(4) Documentation that FOOD EMPLOYEES acknowledge that they have received training in:
(a) The RISKs of contacting the specific READY-TO-EAT FOODS with bare hands,
(b) Proper handwashing as specified under § 2-301.12,
(c) When to wash their hands as specified under § 2-301.14,
(d) Where to wash their hands as specified under § 2-301.15,
(e) Proper fingernail maintenance as specified under § 2-302.11,
(f) Prohibition of jewelry as specified under § 2-303.11, and
(g) Good hygienic practices as specified under §§ 2-401.11 and 2-401.12;
(5) Documentation that hands are washed before FOOD preparation and as necessary to prevent cross
contamination by FOOD EMPLOYEES as specified under §§ 2-301.11, 2-301.12, 2-301.14, and 2-
301.15 during all hours of operation when the specific READY-TO-EAT FOODS are prepared;
(6) Documentation that FOOD EMPLOYEES contacting READY-TO-EAT FOOD with bare hands use two or
more of the following control measures to provide additional safeguards to HAZARDS associated
with bare hand contact;
(a) Double handwashing,
(b) Nail brushes,
(c) A hand antiseptic after handwashing as specified under § 2-301.16,
(d) Incentive programs such as paid sick leave that assist or encourage FOOD EMPLOYEES not to
work when they are ill, or
(e) Other control measures APPROVED by the REGULATORY AUTHORITY; and
51
(7) Documentation that corrective action is taken when Subparagraphs (E)(1)-(6) of this section are
not followed.
3-301.12 PREVENTING CONTAMINATION WHEN TASTING
A FOOD EMPLOYEE may not use a UTENSIL more than once to taste FOOD that is to be sold or served. P
PREVENTING FOOD AND INGREDIENT CONTAMINATION
3-302.11 PACKAGED AND UNPACKAGED FOOD – SEPARATION, PACKAGING, AND
SEGREGATION
(A) FOOD shall be protected from cross contamination by:
(1) Except as specified in (1)(c) below, separating raw animal FOODS during storage, preparation,
holding, and display from:
(a) Raw READY-TO-EAT FOOD including other raw animal FOOD such as FISH for sushi or
MOLLUSCAN SHELLFISH, or other raw READY-TO-EAT FOOD such as fruits and vegetables, P and
(b) Cooked READY-TO-EAT FOOD, P
(c) Frozen, commercially processed and PACKAGED raw animal FOOD may be stored or displayed
with or above frozen, commercially processed and PACKAGED, READY-TO-EAT FOOD.
(2) Except when combined as ingredients, separating types of raw animal FOODS from each other
such as beef, FISH, lamb, pork, and POULTRY during storage, preparation, holding and display by:
(a) Using separate EQUIPMENT for each type, P or
(b) Arranging each type of FOOD in EQUIPMENT so that cross contamination of one type with
another is prevented, P and
(c) Preparing each type of FOOD at different times or in separate areas, P
(3) Cleaning EQUIPMENT and UTENSILS as specified under ¶ 4-602.11(A) and SANITIZING as specified
under § 4-703.11;
(4) Except as specified under Subparagraph 3-501.15(B)(2) and in ¶ (B) of this section, storing the
FOOD in packages, covered containers, or wrappings;
(5) Cleaning HERMETICALLY SEALED CONTAINERS of FOOD of visible soil before opening;
(6) Protecting FOOD containers that are received PACKAGED together in a case or overwrap from cuts
when the case or overwrap is opened;
(7) Storing damaged, spoiled, or recalled FOOD being held in the FOOD ESTABLISHMENT as specified
under § 6-404.11; and
(8) Separating fruits and vegetables, before they are washed as specified under § 3-302.15 from
READY-TO-EAT FOOD.
(B) Subparagraph (A)(4) of this section does not apply to:
(1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling
before consumption;
(2) PRIMAL CUTS, quarters, or sides of raw MEAT or slab bacon that are hung on clean, SANITIZED hooks
or placed on clean, SANITIZED racks;
(3) Whole, uncut, processed MEATS such as country hams, and smoked or cured sausages that are
placed on clean, SANITIZED racks;
(4) FOOD being cooled as specified under Subparagraph 3-501.15(B)(2); or
(5) SHELLSTOCK.
52
3-302.12 FOOD STORAGE CONTAINERS, IDENTIFIED WITH COMMON NAME OF FOOD
Except for containers holding FOOD that can be readily and unmistakably recognized such as dry pasta, working
containers holding FOOD or FOOD ingredients that are removed from their original packages for use in the
FOOD ESTABLISHMENT, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified
with the common name of the FOOD.
3-302.13 PASTEURIZED EGGS, SUBSTITUTE FOR RAW EGGS FOR CERTAIN RECIPES
Pasteurized EGGS or EGG PRODUCTS shall be substituted for raw EGGS in the preparation of FOODS such as Caesar
salad, hollandaise or Béarnaise sauce, mayonnaise, meringue, EGGnog, ice cream, and EGG-fortified BEVERAGES
that are not: P
(A) Cooked as specified under Subparagraphs 3-401.11(A)(1) or (2); P or
(B) Included in ¶ 3-401.11(D). P
3-302.14 PROTECTION FROM UNAPPROVED ADDITIVES
(A) FOOD shall be protected from contamination that may result from the addition of, as specified in § 3-
302.12:
(1) Unsafe or unAPPROVED FOOD or COLOR ADDITIVES, P and
(2) Unsafe or unAPPROVED levels of APPROVED FOOD and color ADDITIVES. P
(B) A FOOD EMPLOYEE may not:
(1) Apply sulfiting agents to fresh fruits and vegetables intended for raw consumption or to a FOOD
considered to be a good source of vitamin B1; P or
(2) Except for grapes, serve or sell FOOD specified under Subparagraph (B)(1) of this section that is
treated with sulfiting agents before receipt by the FOOD ESTABLISHMENT. P
3-302.15 WASHING FRUITS AND VEGETABLES
(A) Except as specified in ¶ (B) of this section and except for whole, raw fruits and vegetables that are
intended for washing by the CONSUMER before consumption, raw fruits and vegetables shall be
thoroughly washed in water to remove soil and other contaminants before being cut, combined with
other ingredients, cooked, served, or offered for human consumption in READY-TO-EAT FORM,
(B) Fruits and vegetables may be washed by using chemicals as specified under § 7-204.12.
(C) Devices used for on-site generation of chemicals meeting the requirements specified in 21 CFR
173.315, Chemicals used in the washing or to assist in the peeling of fruits and vegetables, for the
washing of raw, whole fruits and vegetables shall be used in accordance with the manufacturer's
instructions. Pf
PREVENTING CONTAMINATION FROM ICE USED AS A COOLANT
3-303.11 ICE USED AS EXTERIOR COOLANT, PROHIBITED AS INGREDIENT
After use as a medium for cooling the exterior surfaces of FOOD such as melons or FISH, PACKAGED FOODS such
as canned BEVERAGES, or cooling coils and tubes of EQUIPMENT, ice may not be used as a FOOD. P
3-303.12 STORAGE OR DISPLAY OF FOOD IN CONTACT WITH WATER OR ICE
(A) PACKAGED FOOD may not be stored in direct contact with ice or water if the FOOD is subject to the entry
of water because of the nature of its packaging, wrapping, or container or it’s positioning in the ice or
water,
(B) Except as specified in ¶¶ (C) and (D) of this section, unPACKAGED FOOD may not be stored in direct
contact with undrained ice.
(C) Whole, raw fruits or vegetables; cut, raw vegetables such as celery or carrot sticks or cut potatoes; and
tofu may be immersed in ice or water.
53
(D) Raw POULTRY and raw FISH that are received immersed in ice in shipping containers may remain that that
condition while in storage awaiting preparation, display, service, or sale.
PREVENTING CONTAMINATION FROM EQUIPMENT, UTENSILS, AND LINENS
3-304.11 FOOD CONTACT WITH EQUIPMENT AND UTENSILS
FOOD shall only contact surfaces of:
(A) EQUIPMENT and UTENSILS that are cleaned as specified under Part 4-6 of this Code and SANITIZED as
specified under Part 4-7 of this Code; P
(B) SINGLE-SERVICE and SINGLE-USE ARTICLES; P or
(C) LINENS, such as cloth napkins, as specified under § 3-304.13 that are laundered as specified under Part
4-8 of this Code. P
3-304.12 IN-USE UTENSILS, BETWEEN-USE STORAGE
During pauses in FOOD preparation or dispensing, FOOD preparation and dispensing UTENSILS shall be stored:
(A) Except as specified under ¶ (B) of this section, in the FOOD with their handles above the top of the FOOD
and the container;
(B) In FOOD that is not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD with their handles above the top of the
FOOD within containers or EQUIPMENT that can be closed, such as bins of sugar, flour, or cinnamon;
(C) On clean portion of the FOOD preparation table or cooking EQUIPMENT only if the in-use UTENSIL and the
FOOD-CONTACT surface of the FOOD preparation table or cooking EQUIPMENT are cleaned and SANITIZED at
a frequency specified under §§ 4-602.11 and 4-702.11;
(D) In running water of sufficient velocity to flush particulates to the drain, if used with moist FOOD such
as ice cream or mashed potatoes;
(E) In a clean, protected location if the UTENSILS, such as ice scoops, are used only with a FOOD that is not
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD; or
(F) In a container of water if the water is maintained at a temperature of at least 57°C (135°F) and the
container is cleaned at a frequency specified under Subparagraph 4-602.11(D)(7).
3-304.13 LINENS AND NAPKINS, USE LIMITATION
LINENS, such as cloth napkins, may not be used in contact with FOOD unless they are used to line a container for
the service of FOODS and the LINENS and napkins are replaced each time the container is refilled for a new
CONSUMER.
3-304.14 WIPING CLOTHS, USE LIMITATION
(A) Cloths in-use for wiping FOOD spills from TABLEWARE and carry-out containers that occur as FOOD is
being served shall be:
(1) Maintained dry; and
(2) Used for no other purpose.
(B) Cloths in-use for wiping counters and other EQUIPMENT surfaces shall be:
(1) Held between uses in a chemical SANITIZER solution at a concentration specified under § 4-
501.114; and
(2) Laundered daily as specified under ¶ 4-802.11(D).
(C) Cloths in-use for wiping surfaces in contact with raw animal FOODS shall be kept separate from cloths
used for other purposes.
(D) Dry wiping cloths and the chemical SANITIZING solutions specified in Subparagraph (B)(1) of this
section in which the wiping cloths are held between uses shall be free of FOOD debris and visible soil.
54
(E) Containers of chemical SANITIZING solutions specified in Subparagraph (B)(1) of this section in which
wet wiping cloths are held between uses shall be stored off the floor and used in a manner that
prevents contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, SINGLE-SERVICE, or SINGLE-USE ARTICLES.
(F) SINGLE-USE disposable SANITIZER wipes shall be used in accordance with EPA-APPROVED manufacturer's
label use instructions.
3-304.15 GLOVES, USE LIMITATION
(A) If used, SINGLE-USE gloves shall be used for only one tack such as working with READY-TO-EAT FOOD or
with raw animal FOOD, used for no other purpose, and discarded when damaged or soiled, or when
interruptions occur in the operation. P
(B) Except as specified in ¶ (C) of this section, slash-resistant gloves that are used to protect the hands
during operations requiring cutting shall be used in direct contact only with FOOD that is subsequently
cooked as specified under Part 3-4 such as frozen FOOD or a PRIMAL CUT of MEAT.
(C) Slash-resistant gloves may be used with READY-TO-EAT FOOD that will not be subsequently cooked if the
slash-resistant gloves have a SMOOTH, durable, and nonabsorbent outer surface; or if the slash-resistant
gloves are covered with a SMOOTH, durable, nonabsorbent glove, or a SINGLE-USE glove.
(D) Cloth gloves may not be used in direct contact with FOOD unless the FOOD is subsequently cooked as
required under Part 3-4 such as frozen FOOD or a PRIMAL CUT of MEAT.
3-304.16 USING CLEAN TABLEWARE FOR SECOND PORTIONS AND REFILLS
(A) Except for refilling a CONSUMER'S drinking cup or container without contact between the pouring
UTENSIL and the lip-contact area of the drinking cup or container, FOOD EMPLOYEES may not use
TABLEWARE, including SINGLE-SERVICE ARTICLES, soiled by the CONSUMER, to provide second portions or
refills.
(B) Except as specified in ¶ (C) of this section, self-service CONSUMERS may not be allowed to use soiled
TABLEWARE, including SINGLE-SERVICE ARTICLES, to obtain additional FOOD from the display and serving
EQUIPMENT.
(C) Drinking cups and containers may be reused by self-service CONSUMERS if refilling is a contamination-free
process as specified under ¶¶ 4-204.13(A), (B), and (D).
3-304.17 REFILLING RETURNABLES
(A) Except as specified in ¶¶ (B)-(E) of this section, empty containers returned to a FOOD ESTABLISHMENT
for cleaning and refilling with FOOD shall be cleaned and refilled in a regulated FOOD PROCESSING PLANT. P
(B) A take-home FOOD container returned to a FOOD ESTABLISHMENT may be refilled at a FOOD ESTABLISHMENT
with FOOD if the FOOD container is:
(1) Designed and constructed for reuse and in accordance with the requirements specified under Part
4-1 and 4-2; P
(2) One that was initially provided by the FOOD ESTABLISHMENT to the CONSUMER, either empty or filled
with FOOD by the FOOD ESTABLISHMENT, for the purpose of being returned for reuse;
(3) Returned to the FOOD ESTABLISHMENT by the CONSUMER after use;
(4) Subject to the following steps before being refilled with FOOD:
(a) Cleaned as specified under Part 4-6 of the Code,
(b) SANITIZED as specified under Part 4-7 of this Code,
(c) Visually inspected by a FOOD EMPLOYEE to verify that the container, as returned, meets the
requirements specified under Part 4-1 and 4-2 P. and
(C) A take-home FOOD container returned to a FOOD ESTABLISHMENT may be refilled at a FOOD ESTABLISHMENT
with BEVERAGE if:
(1) The BEVERAGE is not a TIME/TEMPERATURE CONTROL FOR SAFETY FOOD;
55
(2) The design of the container and of the rinsing EQUIPMENT and the nature of the BEVERAGE, when
considered together allow effective cleaning at home or in the FOOD ESTABLISHMENT.
(3) Facilities for rinsing before refilling returned containers with fresh, hot water that is under
pressure and not recirculated are provided as part of the dispensing system;
(4) The CONSUMER-owned container returned to the FOOD ESTABLISHMENT for refilling is refilled for sale
or service only to the same CONSUMER; and
(5) The CONTAINER is refilled by:
(a) An EMPLOYEE of the FOOD ESTABLISHMENT, or
(b) The owner of the container if the BEVERAGE system includes a contamination-free transfer
process as specified under ¶¶ 4-204.13(A), (B), and (D) that cannot be bypassed by the
container owner.
(D) CONSUMER-owned, personal take-out BEVERAGE containers, such as thermally insulated bottles, non-spill
coffee cups, and promotional BEVERAGE glasses, may be refilled by EMPLOYEES or the CONSUMER if refilling is
a contamination-free process as specified under ¶¶ 4-204.13(A), (B), and (D).
(E) CONSUMER-owned containers that are not FOOD-specific may be filled at a water VENDING MACHINE or
system.
PREVENTING CONTAMINATION FROM THE PREMISES
3-305.11 FOOD STORAGE
(A) Except as specified in ¶¶ (B) and (C) of this section, FOOD shall be protected from contamination by
storing the FOOD:
(1) In a clean, dry location;
(2) Where it is not exposed to splash, dust, or other contamination; and
(3) At least 15 cm (6 inches) above the floor.
(B) FOOD in packages and working containers may be stored less than 15 cm (6 inches) above the floor on
case lot handling EQUIPMENT as specified under § 4-204.122.
(C) Pressurized BEVERAGE containers, cased FOOD in waterproof containers such as bottles or cans, and milk
containers in plastic crates may be stored on a floor that is clean and not exposed to floor moisture.
3-305.12 FOOD STORAGE, PROHIBITED AREAS
FOOD may not be stored:
(A) In locker rooms;
(B) In toilet rooms;
(C) In dressing rooms;
(D) In garbage rooms;
(E) In mechanical rooms;
(F) Under sewer lines that are not shielded to intercept potential drips;
(G) Under leaking water lines, including leaking automatic fire sprinkler heads, or under lines on which
water has condensed;
(H) Under open stairwells; or
(I) Under other sources of contamination.
56
3-305.13 VENDED TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, ORIGINAL
CONTAINER
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD dispensed through a VENDING MACHINE shall be in the PACKAGE in
which it was placed at the FOOD ESTABLISHMENT or FOOD PROCESSING PLANT at which it was prepared.
3-305.14 FOOD PREP
During preparation, unPACKAGED FOOD shall be protected from environmental sources of contamination.
PREVENTING CONTAMINATION BY CONSUMERS
3-306.11 FOOD DISPLAY
Except for nuts in the shell and whole, raw fruits and vegetables that are intended for hulling, peeling, or
washing by the CONSUMER before consumption, FOOD on display shall be protected from contamination by the
use of PACKAGING; counter, service line, or salad bar FOOD guards; display cases; or other effective means. P
3-306.12 CONDIMENTS, PROTECTION
(A) Condiments shall be protected from contamination by being kept in dispensers that are designed to
provide protection, protected FOOD displays provided with the proper UTENSILS, original containers
designed for dispensing, or individual PACKAGES or portions.
(B) Condiments at a VENDING MACHINE location shall be in individual PACKAGES or provided in dispensers
that are filled at an APPROVED location, such as the FOOD ESTABLISHMENT that provides FOOD to the
VENDING MACHINE LOCATION, a FOOD PROCESSING PLANT that is regulated by the agency that has jurisdiction
over the operation, or a properly equipped facility that is located on the site of the VENDING MACHINE
LOCATION.
3-306.13 CONSUMER SELF-SERVICE OPERATIONS
(A) Raw, unPACKAGED animal FOOD, such as beef, lamb, pork, POULTRY, and FISH may not be offered for
CONSUMER self-service. This paragraph does not apply to:
(1) CONSUMER self-service of READY-TO-EAT FOODS at buffets or salad bars that serve FOODS such as sushi
or raw shellfish;
(2) Ready-to-cook individual portions for immediate cooking and consumption on the PREMISES such
as CONSUMER-cooked MEATS or CONSUMER-selected ingredients for Mongolian barbecue; or
(3) Raw, frozen, shell-on shrimp or lobster.
(B) CONSUMER self-service operations for READY-TO-EAT FOODS shall be provided with suitable UTENSILS or
effective dispensing methods that protect the FOOD from contamination. Pf
(C) CONSUMER self-service operations such as buffets and salad bars shall be monitored by FOOD EMPLOYEES
trained in safe operating procedures. Pf
3-306.14 RETURNED FOOD AND RE-SERVICE OF FOOD
(A) Except as specified in ¶ (B) of this section, after being served or sold and in the possession of a
CONSUMER, FOOD that is unused or returned by the CONSUMER may not be offered as FOOD for human
consumption. P
(B) Except as specified under ¶ 3-801.11(G), a container of FOOD that is not TIME/TEMPERATURE CONTROL FOR
SAFETY FOOD may be RE-SERVED from one CONSUMER to another if:
(1) The FOOD is dispensed so that it is protected from contamination and the container is closed
between uses, such as a narrow-neck bottle containing catsup, steak sauce, or wine; or
(2) The FOOD, such as crackers, salt, or pepper, is in an unopened original PACKAGE and is maintained in
sound condition.
57
PREVENTING CONTAMINATION FROM OTHER SOURCES
3-307.11 MISECLLANEOUS SOURCES OF CONTAMINATION
FOOD shall be protected from contamination that may result from a factor or source not specified under
Subparts 3-301 - 3-306.
3-4 DESTRUCTION OF ORGANISMS OF PUBLIC HEALTH CONCERN
SUBPARTS 3-401 Cooking
3-402 Freezing
3-403 Reheating
3-404 Other Methods
COOKING
3-401.11 RAW ANIMAL FOODS
(A) Except as specified under ¶ (B) and ¶¶ (C) and(D) of this section, raw animal FOODS such as EGGS, FISH,
MEAT, POULTRY, and FOODS containing these raw animal FOODS, shall be cooked to heat all parts of the
FOOD to a temperature and for a time that complies with one of the following methods based on the
FOOD that is being cooked:
(1) 63°C (145°F) or above for 15 seconds for: P
(a) Raw EGGS that are broken and prepared in response to a CONSUMER’S order and for
immediate service, P and
(b) Except as specified under Subparagraphs (A)(2) and (A)(3) and ¶ (B), and in ¶ (C) of this
section, FISH and MEAT including GAME ANIMALS commercially raised for FOOD as specified
under Subparagraph 3-201.17(A)(1) and GAME ANIMALS under a voluntary inspection
program as specified under Subparagraph 3-201.17(A)(2). P
(2) 68°C (155°F) for 15 seconds or the temperature specified in the following chart that
corresponds to the holding time FOR RATITES, MECHANICALLY TENDERIZED, and INJECTED MEATS; the
following if they are COMMINUTED: FISH, MEAT, GAME ANIMALS, commercially raised for FOOD as
specified under Subparagraph 3-201.17(A)(1), and GAME ANIMALS under a voluntary inspection
program as specified under Subparagraph 3-201.17(A)(2); and raw EGGS that are not prepared
as specified under Subparagraph (A)(1)(a) of this section: P
Minimum Temperature Minimum Time
63°C (145°F) 3 minutes
66°C (150°F) 1 minute
70°C (158°F) < 1 second (instantaneous)
(3) 74°C (165°F) or above for 15 seconds for POULTRY, BALUTS, wild GAME ANIMALS as specified under
Subparagraphs 3-201.17(A)(3) and (4), stuffed FISH, stuffed MEAT, stuffed pasta, stuffed POULTRY,
stuffed RATITES, or stuffing containing FISH, MEAT, POULTRY, or RATITES. P
(B) Whole MEAT roasts including beef, corned beef, lamb, pork, and cured pork roasts such as ham shall be
cooked:
(1) In an oven that is preheated to the temperature specified for the roast's weight in the following
chart and that is held at that temperature: Pf
58
Oven Type Less than 4.5 kg (10 lbs.) 4.5 kg (10 lbs.) or More
Still Dry 177°C (350°F) or more 121°C (250°F) or more
Convection 163°C (325°F) or more 121°C (250°F) or more
High Humidity1 121°C (250°F) or less 121°C (250°F) or less
1Relative humidity greater than 90% for at least 1 hour as measured in the cooking chamber or exit of the
oven, or in a moisture-impermeable bag that provides 100% humidity.
and;
(2) As specified in the following chart, to heat all parts of the FOOD to a temperature and for the
holding time that corresponds to that temperature: P
Temperature Time in Minutes1
54.4°C (130°F) 112
55.0°C (131°F) 89
56.1°C (133°F) 56
57.2°C (135°F) 36
57.8°C (136°F) 28
58.9°C (138°F) 18
60.0°C (140°F) 12
61.1°C (142°F) 8
62.2°C (144°F) 5
62.8°C (145°F) 4
Temperature Time in Seconds1
63.9°C (147°F) 134
65.0°C (149°F) 85
66.1°C (151°F) 54
67.2°C (153°F) 34
68.3°C (155°F) 22
69.4°C (157°F) 14
70.0°C (158°F) 0
1Holding time may include post-oven heat rise.
(C) A raw or undercooked WHOLE-MUSCLE, INTACT BEEF STEAK may be served or offered for sale in a READY-TO-
EAT form if:
(1) The FOOD ESTABLISHMENT serves a population that is not a HIGHLY SUSCEPTIBLE POPULATION,
(2) The steak is labeled to indicate that it meets the definition of "WHOLE-MUSCLE, INTACT BEEF" as
specified under ¶ 3-201.11(E); and
(3) The steak is cooked on both the top and bottom to surface temperature of 63°C (145°F) or above
and a cooked color change is achieved on all external surfaces.
(D) A raw animal FOOD such as raw EGG, raw FISH, raw-marinated FISH, raw MOLLUSCAN SHELLFISH, or steak
tartare; or a partially cooked FOOD such as lightly cooked FISH, soft cooked EGGS, or rare MEAT other than
59
WHOLE-MUSCLE, INTACT BEEF steaks as specified in ¶ (C) of this section, may be served or offered for sale
upon CONSUMER request or selection in a READY-TO-EAT form if:
(1) As specified under ¶¶ 3-801.11(C)(1) and (2), the FOOD ESTABLISHMENT serves a population that is
not a HIGHLY SUSCEPTIBLE POPULATION;
(2) The FOOD, if served or offered for service by CONSUMER selection from a children's menu, does not
contain COMMINUTED MEAT; Pf and
(3) The CONSUMER is informed as specified under § 3-603.11 that to ensure its safety, the FOOD should
be cooked as specified under ¶ (A) or (B) of this section; or
(4) The REGULATORY AUTHORITY grants a VARIANCE from ¶ (A) or (B) of this section as specified in § 8-
103.10 based on a HACCP PLAN that:
(a) Is submitted by the PERMIT HOLDER and APPROVED as specified under § 8-103.11,
(b) Documents scientific data or other information showing that a lesser time and
temperature regimen results in a safe FOOD, and
(c) Verifies that EQUIPMENT and procedures for FOOD preparation and training of FOOD
EMPLOYEES at the FOOD ESTABLISHMENT meet the conditions of the VARIANCE.
3-401.12 MICROWAVE COOKING
Raw animal FOODS cooked in a microwave oven shall be:
(A) Rotated or stirred throughout or midway during cooking to compensate for uneven distribution of
heat;
(B) Covered to retain surface moisture;
(C) Heated to a temperature of at least 74°C (165°F) in all parts of the FOOD, P and
(D) Allowed to stand covered for 2 minutes after cooking to obtain temperature equilibrium.
3-401.13 PLANT FOOD COOKING FOR HOT HOLDING
Fruits and vegetables that are cooked for hot holding shall be cooked to a temperature of 57°C (135°F). Pf
3-401.14 NON-CONTINUOUS COOKING OF RAW ANIMAL FOODS
Raw animal FOODS that are cooked using a NON-CONTINUOUS COOKING process shall be:
(A) Subject to an initial heating process that is no longer than sixty minutes in duration; P
(B) Immediately after initial heating, cooled according to the time and temperature parameters specified
for cooked TIME/TEMPERATURE CONTROL FOR SAFETY FOOD under ¶ 3-501.14(A); P
(C) After cooling, held frozen or cold, as specified for TIME/TEMPERATURE CONTROL FOR SAFETY FOOD under ¶
3-501.16(A)(2); P
(D) Prior to sale or service, cooked using a process that heats all parts of the FOOD to a temperature and
for a time as specified under ¶¶ 3-401.11(A)-(C); P
(E) Cooled according to the time and temperature parameters specified for cooked TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD under ¶ 3-501.14(A) if not either hot held as specified under ¶ 3-501.16(A),
served immediately, or held using time as a public health control as specified under § 3-501.19 after
complete cooking; P and
(F) Prepared and stored according to written procedures that:
(1) Have obtained prior APPROVAL from the REGULATORY AUTHORITY; Pf
(2) Are maintained in the FOOD ESTABLISHMENT and are available to the REGULATORY AUTHORITY upon
request; Pf
(3) Describe how the requirements specified under ¶ (A) - (E) of this Section are to be monitored
and documented by the PERMIT HOLDER and the corrective actions to be taken if the
requirements are not met; Pf
60
(4) Describe how the FOODS, after initial heating, but prior to complete cooking, are to be marked or
otherwise identified as FOODS that must be cooked as specified under ¶ (D) of this Section prior
to being offered for sale or service, Pf and
(5) Describe how the FOODS, after initial heating but prior to cooking as specified under ¶ (D) of this
Section, are to be separated from READY-TO-EAT FOODS as specified under ¶ 3-302.11 (A). Pf
FREEZING
3-402.11 PARASITIC DESTRUCTION
(A) Except as specified in ¶ (B) of this section, before service or sale in READY-TO-EAT form, raw, raw-
marinated, partially cooked, or marinated-partially cooked FISH shall be:
(1) Frozen and stored at a temperature of -20°C (-4°F) or below for a minimum of 168 hours (7
days) in a freezer; P
(2) Frozen at -35°C (-31°F) or below until solid and stored at -35°C (-31°F) or below for a
minimum of 15 hours; P or
(3) Frozen at -35°C (-31°F) or below until solid and stored at -20°C (-4°F) or below for a minimum
24 hours. P
(B) Paragraph (A) of this section does not apply to:
(1) MOLLUSCAN SHELLFISH;
(2) A scallop product consisting only of the shucked adductor muscle;
(3) Tuna of the species Thunnus alalunga, Thunnus albacares (Yellowfin tuna), Thunnus atlanticus,
Thunnus maccoyi (Bluefin tuna, Southern). Thunnus obesus (Bigeye tuna), or Thunnus thynnus
(Bluefin tuna, Northern); or
(4) Aquacultured FISH, such as salmon that:
(a) If raised in open water, are raised in net-pens, or
(b) Are raised in land-based operations such as ponds or tanks, and
(c) Are fed formulated feed, such as pellets, that contains no live parasites infective to the
aquacultured FISH.
(5) FISH EGGS that have been removed from the skein and rinsed.
3-402.12 RECORDS, CREATION AND RETENTION
(A) Except as specified in ¶ 3-402.11(B) and ¶ (B) of this section, if raw, raw-marinated, partially cooked,
or marinated-partially cooked FISH are served or sold in READY-TO-EAT form, the PERSON IN CHARGE shall
record the freezing temperature and time to which the FISH are subjected and shall retain the records
of the FOOD ESTABLISHMENT for 90 calendar days beyond the time of service or sale of the FISH. Pf
(B) If the FISH are frozen by a supplier, a written agreement or statement from the supplier stipulating that
the FISH supplied are frozen to a temperature and for a time specified under § 3-402.11 may substitute
for the records specified under ¶ (A) of this section.
(C) If raw, raw-marinated, partially cooked, or marinated-partially cooked FISH are served or sold in
READY-TO-EAT form, and the FISH are raised and fed as specified in Subparagraph 3-402.11 (B)(3), a
written agreement or statement from the supplier or aquaculturist stipulating that the FISH were
raised and fed as specified in Subparagraph 3-402.11(B)(3) shall be obtained by the PERSON IN CHARGE
and retained in the records of the FOOD ESTABLISHMENT for 90 calendar days beyond the time of service
or sale of the FISH. Pf
61
REHEATING
3-403.10 PREPARATION FOR IMMEDIATE SERVICE
Cooked and refrigerated FOOD that is prepared for immediate service in response to an individual CONSUMER
order, such as a roast beef sandwich au jus, may be served at any temperature.
3-403.11 REHEATING FOR HOT HOLDING
(A) Except as specified under ¶ (B) and ¶ (C) and ¶ (E) of this section, TIME/TEMPERATURE CONTROL FOR
SAFETY FOOD that is cooked, cooled, and reheated for hot holding shall be reheated so that all parts of
the FOOD reach a temperature of at least 74°C (165°F) for 15 seconds. P
(B) Except as specified under ¶ (C) of this section, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is
reheated in a microwave oven for hot holding shall be reheated so that all parts of the FOOD reach a
temperature of at least 74°C (165°F) and the FOOD is rotated or stirred, covered, and allowed to stand
covered for 2 minutes after reheating. P
(C) READY-TO-EAT TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that has been commercially processed and
PACKAGED in a FOOD PROCESSING PLANT that is inspected by the REGULATORY AUTHORITY that has jurisdiction
over the plant, shall be heated to a temperature of at least 57°C (135°F) when being reheated for hot
holding. P
(D) Reheating for hot holding as specified under ¶ ¶ (A)-(C) of this section shall be done rapidly and the
time the FOOD is between 5°C (41°F) and the temperatures specified under ¶ ¶ (A)-(C) of this section
may not exceed 2 hours. P
(E) Remaining unsliced portions of MEAT roasts that are cooked as specified under ¶ 3-401.11(B) may be
reheated for hot holding using the oven parameters and minimum time and temperature conditions
specified under ¶ 3-401.11(B).
OTHER METHODS
3-404.11 TREATING JUICE
JUICE PACKAGED in a FOOD ESTABLISHMENT shall be:
(A) Treated under a HACCP PLAN as specified in ¶¶ 8-201.14(B)-(E) to attain a 5-log reduction, which is
equal to a 99.999% reduction, of the most resistant microorganism of public health significance; P or
(B) Labeled, if not treated to yield a 5-log reduction of the most resistant microorganism of public health
significance: Pf
(1) As specified under § 3-602.11, Pf and
(2) As specified in 21 CFR 101.17(g) FOOD labeling, warning, notice, and safe handling statements,
JUICES that have not been specifically processed to prevent, reduce, or eliminate the presence of
pathogens with the following, "WARNING: This product has not been pasteurized and,
therefore, may contain harmful bacteria that can cause serious illness in children, the elderly,
and PERSONS with weakened immune systems." Pf
3-5 LIMITATION OF GROWTH OF ORGANISMS OF PUBLIC HEALTH CONCERN
SUBPARTS 3-501 Temperature and Time Control
3-502 Specialized Processing Methods
TEMPERATURE AND TIME CONTROL
3-501.11 FROZEN FOOD
Stored frozen FOODS shall be maintained frozen.
62
3-501.12 TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, SLACKING
Frozen TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is slacked to moderate the temperature shall be held:
(A) Under refrigeration that maintains the FOOD temperature at 5°C (41°F) or less; or
(B) At any temperature if the FOOD remains frozen.
3-501.13 THAWING
Except as specified in ¶ (D) of this section, TIME/ TEMPERATURE CONTROL FOR SAFETY FOOD shall be thawed:
(A) Under refrigeration that maintains the FOOD temperature at 5°C (41°F) or less; or
(B) Completely submerged under running water:
(1) At a water temperature of 21°C (70°F) or below,
(2) With sufficient water velocity to agitate and float off loose particles in an overflow, and
(3) For a period of time that does not allow thawed portions of READY-TO-EAT FOOD to rise above 5°C
(41°F), or
(4) For a period of time that does not allow thawed portions of a raw animal FOOD requiring
cooking as specified under ¶ 3-401.11(A) or (B) to be above 5°C (41°F), for more than 4 hours
including:
(a) The time the FOOD is exposed to the running water and the time needed for preparation
for cooking, or
(b) The time it takes under refrigeration to lower the FOOD temperature to 5°C (41°F), or
(C) As part of a cooking process if the FOOD that is frozen is:
(1) Cooked as specified under ¶¶ 3-401.11(A) or (B) or § 3-401.12, or
(2) Thawed in a microwave oven and immediately transferred to conventional cooking EQUIPMENT,
with no interruption in the process; or
(D) Using any procedure if a portion of frozen READY-TO-EAT FOOD is thawed and prepared for immediate
service in response to an individual CONSUMER'S order.
(E) REDUCED OXYGEN PACKAGED FISH that bears a label indicating that it is to be kept frozen until time of use
shall be removed from the reduced oxygen environment:
(1) Prior to its thawing under refrigeration as specified in ¶ (A) of this section; or
(2) Prior to, or immediately upon completion of its thawing using procedures specified in ¶ (B) of
this section.
3-501.14 COOLING
(A) Cooked TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall be cooled:
(1) Within 2 hours from 57°C (135°F) to 21°C (70°F); P and
(2) Within a total of 6 hours from 57°C (135°F) to 5°C (41°F) or less. P
(B) TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall be cooled within 4 hours to 5°C (41°F) or less, if
prepared from ingredients at ambient temperature, such as reconstituted FOODS and canned tuna. P
(C) Except as specified under ¶ (D) of this section, a TIME/TEMPERATURE CONTROL FOR SAFETY FOOD received
in compliance with LAWS allowing a temperature above 5°C (41°F) during shipment from the supplier
as specified in ¶ 3-202.11(B), shall be cooled within 4 hours to 5°C (41°F) or less. P
(D) Raw EGGS shall be received as specified under ¶ 3-202.11(C) and immediately placed in refrigerated
EQUIPMENT that maintains an ambient air temperature of 7°C (45°F) or less. P
3-501.15 COOLING METHODS
(A) Cooling shall be accomplished in accordance with the time and temperature criteria specified under §
3-501.14 by using one or more of the following methods based on the type of FOOD being cooled:
63
(1) Placing the FOOD in shallow pans; Pf
(2) Separating the FOOD into smaller or thinner portions; Pf
(3) Using rapid cooling EQUIPMENT; Pf
(4) Stirring the FOOD in a container placed in an ice water bath; Pf
(5) Using containers that facilitate heat transfer; Pf
(6) Adding ice as an ingredient; or Pf
(7) Other effective methods, Pf
(B) When placed in cooling or cold holding EQUIPMENT, FOOD containers in which FOOD is being cooled shall
be:
(1) Arranged in the EQUIPMENT to provide maximum heat transfer through the container walls; and
(2) Loosely covered, or uncovered if protected from overhead contamination as specified under
Subparagraph 3-305.11(A)(2), during the cooling period to facilitate heat transfer from the
surface of the FOOD.
3-501.16 TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, HOT AND COLD HOLDING
(A) Except during preparation, cooking, or cooling, or when time is used as the public health control as
specified under § 3-501.19, and except as specified under ¶ (B) and in ¶ (C) of this section,
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall be maintained:
(1) At 57°C (135°F) or above, except that roasts cooked to a temperature and for a time specified in
¶ 3-401.11(B) or reheated as specified in ¶ 3-403.11(E) may be held at a temperature of 54°C
(130°F) or above; P or
(2) At 5°C (41°F) or less. P
(B) EGGS that have not been treated to destroy all viable Salmonellae shall be stored in refrigerated
EQUIPMENT that maintains an ambient air temperature of 7°C (45°F) or less. P
(C) TIME/TEMPERATURE CONTROL FOR SAFETY FOOD in a homogenous liquid form may be maintained outside of
the temperature control requirements, as specified under ¶ (A) of this section, while contained within
specially designed EQUIPMENT that complies with the design and construction requirements as specified
under ¶ 4-204.13(E).
3-501.17 READY-TO-EAT, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD,
DATE MARKING
ON-PREMISES PREPARATION - Prepare and Hold Cold
(A) Except when PACKAGING FOOD using a REDUCED OXYGEN PACKAGING method as specified under § 3-502.12,
and except as specified in ¶¶ (E) and (F) of this section, refrigerated, READY-TO-EAT, TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD prepared and held in a FOOD ESTABLISHMENT for more than 24 hours shall be
clearly marked to indicate the date, or day by which the FOOD shall be consumed on the PREMISES, sold,
or discarded when held at a temperature of 5°C (41°F) or less for a maximum of 7 days. The day of
preparation shall be counted as Day 1. Pf
COMMERCIALLY PROCESSED FOOD - Open and Hold Cold
(B) Except as specified in ¶¶ (E)-(G) of this section, refrigerated, READY-TO-EAT TIME/TEMPERATURE CONTROL
FOR SAFETY FOOD prepared and PACKAGED by a FOOD PROCESSING PLANT shall be clearly marked, at the time
the original container is opened in a FOOD ESTABLISHMENT and if the FOOD is held for more than 24
hours, to indicate the date or day by which the FOOD shall be consumed on the PREMISES, sold, or
discarded, based on the temperature and time combinations specified in ¶ (A) of this section, and: Pf
(1) The day the original container is opened in the FOOD ESTABLISHMENT shall be counted as Day 1; Pf
and
(2) The day or date marked by the FOOD ESTABLISHMENT may not exceed a manufacturer's use-by
date if the manufacturer determined the use-by date based on FOOD safety. Pf
64
(C) A refrigerated, READY-TO-EAT TIME/TEMPERATURE CONTROL FOR SAFETY FOOD ingredient or a portion of a
refrigerated, READY-TO-EAT TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is subsequently combined
with additional ingredients or portions of FOOD shall retain the date marking of the earliest-prepared
or first-prepared ingredient. Pf
(D) A date marking system that meets the criteria stated in ¶¶ (A) and (B) of this section may include:
(1) Using a method APPROVED by the REGULATORY AUTHORITY for refrigerated, READY-TO-EAT
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is frequently rewrapped, such as lunchMEAT or a
roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing
machine;
(2) Marking the date or day of preparation, with a procedure to discard the FOOD on or before the last
date or day by which the FOOD must be consumed on the PREMISES, sold, or discarded as specified
under ¶ (A) of this section;
(3) Marking the date or day the original container is opened in a FOOD ESTABLISHMENT, with a
procedure to discard the FOOD on or before the last date or day by which the FOOD must be
consumed on the PREMISES, sold, or discarded as specified under ¶ (B) of this section;
(4) Using calendar dates, days of the week, color-coded marks, or other effective marking methods,
provided that the marking system is disclosed to the REGULATORY AUTHORITY upon request.
(E) Paragraphs (A) and (B) of this section do not apply to individual meal portions served or rePACKAGED for
sale from a bulk container upon a CONSUMER's request.
(F) Paragraphs (A) and (B) of this section do not apply to SHELLSTOCK.
(G) Paragraph (B) of this section does not apply to the following FOODS prepared and PACKAGED by a FOOD
PROCESSING PLANT inspected by a REGULATORY AUTHORITY;
(1) Deli salads, such as ham salad, seafood salad, chicken salad, EGG salad, pasta salad, potato salad,
and macaroni salad, manufactured in accordance with 21 CFR 110 Current good manufacturing,
packing, or holding human FOOD;
(2) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and
related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;
(3) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as
defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola,
gouda, and monterey jack;
(4) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and
buttermilk;
(5) Preserved FISH products, such as pickled herring and dried or salted cod, and other acidified FISH
products defined in 21 CFR 114 Acidified FOODS;
(6) Shelf stable, dry fermented sausages, such as pepperoni and Genoa; and
(7) Shelf stable salt-cured products such as prosciutto and Parma (ham).
3-501.18 READY-TO-EAT, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, DISPOSITION
(A) A FOOD specified in ¶ 3-501.17(A) or (B) shall be discarded if it:
(1) Exceeds the temperature and time combination specified in ¶ 3-501.17(A), except time that the
product is frozen; P
(2) Is in a container or PACKAGE that does not bear a date or day; P or
(3) Is appropriately marked with a date or day that exceeds a temperature and time combination
as specified in ¶ 3-501.17(A). P
(B) Refrigerated, READY-TO-EAT, TIME/TEMPERATURE CONTROL FOR SAFETY FOOD prepared in a FOOD
ESTABLISHMENT and dispensed through a VENDING MACHINE with an automatic shutoff control shall be
discarded if it exceeds a temperature and time combination as specified in ¶ 3-501.17(A). P
65
3-501.19 TIME AS A PUBLIC HEALTH CONTROL
(A) Except as specified under ¶ (D) of this section, if time without temperature control is used as the
public health control for a working supply OF TIME/ TEMPERATURE CONTROL FOR SAFETY FOOD before
cooking, or for READY-TO-EAT TIME/ TEMPERATURE CONTROL FOR SAFETY FOOD that is displayed or held for
sale or service;
(1) Written procedures shall be prepared in advance, maintained in the FOOD ESTABLISHMENT and
made available to the REGULATORY AUTHORITY upon request that specify; Pf
(a) Methods of compliance with Subparagraphs (B)(1)-(3) or (c)(1)-(5) of this section; Pf and
(b) Methods of compliance with § 3-501.14 for FOOD that is prepared, cooked, and
refrigerated before time is used as a public health control. Pf
TIME - MAXIMUM UP TO 4 HOURS
(B) If time without temperature control is used as the public health control up to a maximum of 4 hours:
(1) The FOOD shall have an initial temperature of 5°C (41°F) or less when removed from cold
holding temperature control, or 57°C (135°F) or greater when removed from hot holding
temperature control; P
(2) The FOOD shall be marked or otherwise identified to indicate the time that is 4 hours past the
point in time when the FOOD is removed from temperature control; Pf
(3) The FOOD shall be cooked and served, served at any temperature if READY-TO-EAT, or discarded,
within 4 hours from the point in time when the FOOD is removed from temperature control; P
and
(4) The FOOD in unmarked containers or packages, or marked to exceed a 4-hour limit shall be
discarded. P
TIME - MAXIMUM UP TO 6 HOURS
(C) If time without temperature control is used as the public health control up to a maximum of 6 hours:
(1) The FOOD shall have an initial temperature of 5°C (41°F) or less when removed from the
temperature control, and the FOOD temperature may not exceed 21°C (70°F) within a
maximum time period of 6 hours; P
(2) The FOOD shall be monitored to ensure the warmest portion of the FOOD does not exceed 21°C
(70°F) during the 6-hour period, unless an ambient air temperature is maintained that ensure
the FOOD does not exceed 21°C (70°F) during the 6-hour holding period; Pf
(3) The FOOD shall be marked or otherwise identified to indicate: Pf
(a) The time when the FOOD is removed from 5°C (41°F) or less cold holding temperature
control, Pf and
(b) The time that is 6 hours past the point in time when the FOOD is removed from cold
holding temperature control; Pf
(4) The FOOD shall be:
(a) Discarded if the temperature of the FOOD exceeds 21°C (70°F), P or
(b) Cooked and served, served at any temperature if READY-TO-EAT, or discarded within a
maximum of 6 hours from the point in time when the FOOD is removed from 5°C (41°F)
or less cold holding temperature control; P and
(5) The FOOD in unmarked containers or PACKAGES, or marked with a time that exceeds the 6-hour
limit shall be discarded. P
(D) A FOOD ESTABLISHMENT that serves a HIGHLY SUSCEPTIBLE POPULATION may not use time as specified under
¶¶ (A), (B), or (C) of this section as the public health control for raw EGGS.
66
SPECIALIZED PROCESSING METHODS
3-502.11 VARIANCE REQUIREMENT
A FOOD ESTABLISHMENT shall obtain a VARIANCE from the REGULATORY AUTHORITY as specified in § 8-103.10 and
under § 8-103.11 before: Pf
(A) Smoking FOOD as a method of FOOD preservation rather than as a method of flavor enhancement; Pf
(B) Curing FOOD; Pf
(C) Using FOOD ADDITIVES or adding components such as vinegar; Pf
(1) As a method of FOOD preservation rather than as a method of flavor enhancement, P or
(2) To render a FOOD so that it is NOT TIME/TEMPERATURE CONTROL OF SAFETY FOOD; Pf
(D) PACKAGING TIME/TEMPERATURE CONTROL FOR SAFETY FOOD using a REDUCED OXYGEN PACKAGING method except
where the growth of and toxin formation by Clostridium botulinum and the growth of Listeria
Monocytogenes are controlled as specified under § 3-502.12; Pf
(E) Operating a MOLLUSCAN SHELLFISH life-support system display tank used to store or display shellfish
that are offered for human consumption; Pf
(F) Custom processing animals that are for personal use as FOOD and not for sale or service in a FOOD
ESTABLISHMENT; Pf
(G) Preparing FOOD by another method that is determined by the REGULATORY AUTHORITY to require a
VARIANCE, Pf or
(H) Sprouting seeds or beans. Pf
CLOSTRIDIUM BOTULINUM AND LISTERIA MONOCYTOGENES CONTROLS
3-502.12 REDUCED OXYGEN PACKAGING, WITHOUT A VARIANCE, CRITERIA
(A) Except for a FOOD ESTABLISHMENT that obtains a VARIANCE as specified under § 3-502.11, a FOOD
ESTABLISHMENT that packages TIME/TEMPERATURE CONTROL FOR SAFETY FOOD using a REDUCED OXYGEN
PACKAGING method shall control the growth and toxin formation of Clostridium botulinum and the
growth of Listeria monocytogenes. P
(B) Except as specified under ¶ (F) of this section, a FOOD ESTABLISHMENT that PACKAGES TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD using a REDUCED OXYGEN PACKAGING method shall implement a HACCP PLAN that
contains the information specified under ¶¶ 8-201.14(B) and (D) and that: Pf
(1) Identifies the FOOD to be PACKAGED; Pf
(2) Except as specified under ¶¶ (C)-(E) of this section, requires that the PACKAGED FOOD shall be
maintained at 5°C (41°F) or less and meet at least one of the following criteria: Pf
(a) Has an Aw of 0.91 or less, Pf
(b) Has a pH of 4.6 or less, Pf
(c) Is a MEAT or POULTRY product cured at a FOOD PROCESSING PLANT regulated by the USDA
using substances specified in 9 CFR 424.21. Use of FOOD ingredients and sources of
radiation, and is received in an intact PACKAGE, Pf or
(d) Is a FOOD with a high level of competing organisms such as raw MEAT, raw POULTRY, or
raw vegetables; Pf
(3) Describes how the PACKAGE shall be prominently and conspicuously labeled on the principal
display panel in bold type on a contrasting background, with instructions to: Pf
(a) Maintain the FOOD at 5°C (41°F) or below, Pf and
(b) Discard the FOOD if within 30 calendar days of its PACKAGING if it is not served for on-
PREMISES consumption, or consumed if served or sold for off-PREMISES consumption; Pf
67
(4) Limits the refrigerated shelf life to no more than 30 calendar days from PACKAGING to
consumption, except the time the product is maintained frozen, or the original manufacturer's
"sell by" or "use by" date, whichever occurs first; P
(5) Includes operational procedures that:
(a) Prohibit contacting READY-TO-EAT FOOD with bare hands as specified under ¶ 3-301.11(B),
Pf
(b) Identify a designated work area and the method by which: Pf
(i.) Physical barriers or methods of separation of raw FOODS and READY-TO-EAT FOODS
minimize cross contamination, Pf and
(ii.) Access to the processing EQUIPMENT is limited to responsible trained personnel
familiar with the potential HAZARDS of the operation, Pf and
(c) Delineate cleaning and SANITIZATION procedures for FOOD-CONTACT SURFACES; Pf and
(6) Describes the training program that ensures that the individual responsible for the REDUCED
OXYGEN PACKAGING operation understands the:
(a) Concepts required for a safe operation, Pf
(b) EQUIPMENT and facilities, Pf and
(c) Procedures specified under Subparagraph (B)(5) of this section and ¶¶ 8-201.14 (B) and
(D). Pf
(7) Is provided to the REGULATORY AUTHORITY prior to implementation as specified under ¶ 8-
201.13(B).
FISH
(C) Except for FISH that is frozen before, during, and after packaging, a FOOD ESTABLISHMENT may not package
FISH using a REDUCED OXYGEN PACKAGING method. P
COOK-CHILL OR SOUS VIDE
(D) Except as specified under ¶ (C) and ¶ (F) of this section, a FOOD ESTABLISHMENT that PACKAGES
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD using a cook-chill or sous vide process shall:
(1) Provide to the REGULATORY AUTHORITY prior to implementation, a HACCP PLAN that contains the
information as specified under ¶¶ 8-201.14 (B) and (D); Pf
(2) Ensure the FOOD is:
(a) Prepared and consumed on the PREMISES, or prepared and consumed off the PREMISES but
within the same business entity with no distribution or sale of the PACKAGED product to
another business entity or the CONSUMER, Pf
(b) Cooked to heat all parts of the FOOD to a temperature and for a time as specified under
¶¶ 3-401.11 (A), (B), and (C), P
(c) Protected from contamination before and after cooking as specified under Parts 3-3 and
3-4, P
(d) Placed in a PACKAGE with an oxygen barrier and SEALED before cooking, or placed in a
PACKAGE and SEALED immediately after cooking and before reaching a temperature below
57°C (135°F), P
(e) Cooled to 5°C (41°F) in the SEALED PACKAGE or bag as specified under § 3-501.14, and P
(i.) Cooled to 1°C (34°F) within 48 hours of reaching 5°C (41°F) and held at that
temperature until consumed or discarded within 30 days after the date of
PACKAGING; P
(ii.) Held at 5°C (41°F) or less for no more than 7 days, at which time the FOOD must
be consumed or discarded; P or
68
(iii.) Held frozen with no shelf life restriction while frozen until consumed or used. P
(f) Held in a refrigeration unit that is equipped with an electronic system that continuously
monitors time and temperature and is visually examined for proper operation twice
daily, Pf
(g) If transported off-site to a satellite location of the same business entity, equipped with
verifiable electronic monitoring devices to ensure that times and temperatures are
monitored during transportation, P and
(h) Labeled with the product name and the date PACKAGED, Pf and
(3) Maintain the records required to confirm that cooling and cold holding refrigeration
time/temperature parameters are required as part of the HACCP PLAN and:
(a) Make such records available to the REGULATORY AUTHORITY upon request, Pf and
(b) Hold such records for at least 6 months, Pf and
(4) Implement written operational procedures as specified under Subparagraph (B)(5) of this
section and a training program as specified under Subparagraph (B)(6) of this section. Pf
CHEESE
(E) Except as specified under ¶ (F) of this section, a FOOD ESTABLISHMENT that PACKAGES cheese using a
REDUCED OXYGEN PACKAGING method shall:
(1) Limit the cheeses PACKAGED to those that are commercially manufactured in a FOOD PROCESSING
PLANT with no ingredients added in the FOOD ESTABLISHMENT and that meet the Standards of
Identity as specified in 21 CFR 133.150 Hard cheeses, 21 CFR 133.169 Pasteurized process
cheese or 21 CFR 133.187 Semisoft cheeses; P
(2) Have a HACCP PLAN that contains the information specified under ¶¶ 8-201.14 (B) and (D) and
as specified under ¶¶ (B)(1), (B)(3)(a), (B)(5) and (B)(6) of this section; Pf
(3) Labels the PACKAGE on the principal display panel with a "use by" date that does not exceed 30
days from its PACKAGING or the original manufacturer's "sell by" or "use by" date, whichever
occurs first; Pf and
(4) Discards the REDUCED OXYGEN PACKAGED cheese if it is not sold for off-PREMISES consumption or
consumed within 30 calendar days of its PACKAGING. Pf
(F) A HACCP PLAN is not required when a FOOD ESTABLISHMENT uses a REDUCED OXYGEN PACKAGING method to
PACKAGE TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is always:
(1) Labeled with the production time and date,
(2) Held at 5°C (41°F) or less during refrigerated storage, and
(3) Removed from its package in the FOOD ESTABLISHMENT within 48 hours after PACKAGING.
IDAPA 16.02.19.355 FOOD PROCESSING PLANTS
FOOD PROCESSING PLANTS, ESTABLISHMENTS, canning factories or operations must meet the requirements in
Chapters 1 through 8 of the 2013 FOOD Code, and Subsections 355.01 through 355.07 of this rule.
01. Thermal Processing of Low-Acid Foods. Low-acid FOOD products processed using thermal
methods for canning must meet the requirements of 21 CFR 113.
02. Processing of Acidified Foods. Acidified food products must meet the requirements of 21 CFR
114.
03. Bottled Water Processing. BOTTLED DRINKING WATER processed in Idaho must meet the
requirements of 21 CFR 129. BOTTLED DRINKING WATER must also meet the quality monitoring
requirements in 21 CFR 165.
04. Approval of Process Methods. A VARIANCE by the REGULATORY AUTHORITY must be APPROVED and
granted for specialized processing methods for products listed in § 3-502.11.
69
05. Labels. Proposed labels shall be submitted to the REGULATORY AUTHORITY for review and APPROVAL
prior to printing.
06. Testing. The LICENSE HOLDER is responsible for chemical, microbiological or extraneous material
testing procedures to identify failures or FOOD contamination of FOOD products being processed or
manufactured by the LICENSE holder.
07. Quality Assurance Program. The LICENSE HOLDER or his designated PERSON must develop and
submit to the REGULATORY AUTHORITY for review and approval a quality assurance program or HACCP
PLAN that covers the FOOD processing operation. The program must include the following:
(a) An organizational chart that identifies PERSONS responsible for quality control operations.
(b) A process flow diagram outlining the processing steps from the receipt of the raw materials to
the production and PACKAGING of finished product(s) or group of related products.
(c) A list of specific points in the process which are CRITICAL CONTROL POINTS that must have
scheduled monitoring.
(d) Product codes that establish and identify the production date and batch.
(e) A manual covering sanitary maintenance of facility and hygienic practices to be followed by
EMPLOYEES.
(f) A records system allowing for review and evaluation of all operations including the quality
assurance program results. These records must be kept for a period of time that exceeds the
shelf life of the product by six (6) months or for two (2) years, whichever is less.
3-6 FOOD IDENTITY, PRESENTATION AND ON-PREMISES LABELING
SUBPARTS 3-601 Accurate Representation
3-602 Labeling
3-603 Consumer Advisory
ACCURATE REPRESENTATION
3-601.11 STANDARDS OF IDENTITY
PACKAGED FOOD shall comply with standard of identity requirements in 21 CFR 131-169 and 9 CFR 319
Definitions and standards of identity or composition, and the general requirements in 21 CFR 130 - Food
Standards: General and 9 CFR 319 Subpart A – General.
3-601.12 HONESTLY PRESENTED
(A) FOOD shall be offered for human consumption in a way that does not mislead or misinform the
CONSUMER.
(B) FOOD or COLOR ADDITIVES, colored overwraps, or lights may not be used to misrepresent the true
appearance, color, or quality of a FOOD.
LABELING
3-602.11 FOOD LABELS
(A) FOOD PACKAGED in a FOOD ESTABLISHMENT, shall be labeled as specified in LAW, including 21 CFR 101 -
FOOD labeling, and 9 CFR 317 Labeling, Marking devices, and containers.
(B) Label information shall include:
(1) The common name of the FOOD, or absent a common name, an adequately descriptive identity
statement;
70
(2) If made from two or more ingredients, a list of ingredients and sub-ingredients in descending
order of predominance by weight, including a declaration of artificial colors, artificial flavors
and chemical preservatives, if contained in the FOOD;
(3) An accurate declaration of the net quantity of contents;
(4) The name and place of business of the manufacturer, packer, or distributor; and
(5) The name of the FOOD source for each MAJOR FOOD ALLERGEN contained in the FOOD unless the
FOOD source is already part of the common or usual name of the respective ingredient. Pf
(6) Except as exempted in the Federal FOOD, Drug, and Cosmetic Act § 403(q)(3) - (5), nutrition
labeling as specified in 21 CFR 101 - FOOD Labeling and 9 CFR 317 Subpart B Nutrition
Labeling.
(7) For any salmonid FISH containing canthaxanthin or astaxanthin as a COLOR ADDITIVE, the labeling
of the bulk FISH container, including a list of ingredients, displayed on the retail container or by
other written means, such as a counter card, that discloses the use of canthaxanthin or
astaxanthin.
(C) Bulk FOOD that is available for CONSUMER self-dispensing shall be prominently labeled with the
following information in plain view of the CONSUMER:
(1) The manufacturer's or processor's label that was provided with the FOOD; or
(2) A card, sign, or other method of notification that includes the information specified under
Subparagraphs (B)(1), (2), and (6) of this section.
(D) Bulk, unPACKAGED FOODS such as bakery products and unPACKAGED FOODS that are portioned to CONSUMER
specification need not be labeled if:
(1) A health, nutrient content, or other claim is not made;
(2) There are no state or local LAWS requiring labeling; and
(3) The FOOD is manufactured or prepared on the PREMISES of the FOOD ESTABLISHMENT or at another
FOOD ESTABLISHMENT or a FOOD PROCESSING PLANT that is owned by the same PERSON and is regulated
by the FOOD regulatory agency that has jurisdiction.
3-602.12 OTHER FORMS OF INFORMATION
(A) If required by LAW, CONSUMER warnings shall be provided.
(B) FOOD ESTABLISHMENT or manufacturers’ dating information on FOODS may not be concealed or altered.
CONSUMER ADVISORY
3-603.11 CONSUMPTION OF ANIMAL FOODS THAT ARE RAW, UNDERCOOKED, OR NOT
OTHERWISE PROCESSED TO ELIMINATE PATHOGENS
IDAPA 16.02.19.360 - ADVISING CONSUMERS OF HEALTH RISK OR RAW OR UNDERCOOKED
FOODS - MODIFICATION TO 3-603-11
01. Consumption of Animal Foods That Are Raw, Undercooked, or Not Otherwise Processed to
Eliminate Pathogens. Except as specified in Section 3-401.11(C) and Subparagraph 3-401.11(D)(3) and
under Section 3-801.11(D), if an animal FOOD such as beef, EGGS, FISH, lamb, milk, pork, POULTRY, or shellfish
that is raw, undercooked or not otherwise processed to eliminate pathogens is offered in a READY-TO-EAT
form as a deli, menu, vended, or other item; or as a raw ingredient in another ready-to-eat food, the LICENSE
HOLDER must inform the consumers of health risks. Pf
02. How to Inform Consumers of Health Risk. The LICENSE HOLDER must use any effective means to inform
consumers of potential health risks. Some effective ways that may be used to inform consumers are:
brochures, deli case placards, signs or verbal warnings, that state, “Consuming raw or undercooked MEATS,
POULTRY, seafood, shellfish, or EGGS may increase your RISK of foodborne illness, especially if you have certain
medical conditions.” Pf
71
3-7 CONTAMINATED FOOD
SUBPART 3-701 Disposition
DISPOSITION
3-701.11 DISCARDING OR RECONDITIONING UNSAFE, ADULTERATED, OR CONTAMINATED
FOOD
(A) A FOOD that is unsafe, ADULTERATED, or not honestly presented as specified under § 3-101.11 shall be
discarded or reconditioned according to an APPROVED procedure. P
(B) FOOD that is not from an APPROVED source as specified under §§ 3-201.11 - 17 shall be discarded. P
(C) READY-TO-EAT FOOD that may have been contaminated by an EMPLOYEE who has been RESTRICTED or
EXCLUDED as specified under § 2-201.12 shall be discarded. P
(D) FOOD that is contaminated by FOOD EMPLOYEES, CONSUMERS, or other PERSONS through contact with their
hands, bodily discharges, such as nasal or oral discharges, or other means shall be discarded. P
IDAPA 16.02.19.370 - ADULTERATED OR MISBRANDED FOOD
The REGULATORY AUTHORITY may order the LICENSE HOLDER or other PERSON who has custody of ADULTERATED or
misbranded FOOD to destroy, denature or recondition ADULTERATED of misbranded FOOD according to Section
37-118, Idaho code. See Section 851 of these rules for EMBARGO, tagging, storage and release of ADULTERATED
or misbranded FOOD.
3-8 SPECIALIZED REQUIREMENTS FOR HIGHLY SUSCEPTIBLE POPULATIONS
SUBPART 3-801 Additional Safeguards
ADDITIONAL SAFEGUARDS
3-801.11 PASTEURIZED FOODS, PROHIBITED RE-SERVICE, AND PROHIBITED FOOD
In a FOOD ESTABLISHMENT that serves a HIGHLY SUSCEPTIBLE POPULATION:
(A) The following criteria apply to JUICE:
(1) For the purposes of this paragraph only, children who are age 9 or less and receive FOOD in a
school, day care setting, or similar facility that provides custodial care are included as HIGHLY
SUSCEPTIBLE POPULATIONS;
(2) PrePACKAGED JUICE or a prePACKAGED BEVERAGE containing JUICE, that bears a warning label as
specified in 21 CFR, 101.17(G) FOOD labeling, warning, notice, and safe handling statements,
JUICES that have not been specifically processed to prevent, reduce or eliminate the presence of
pathogens, or a PACKAGED JUICE or BEVERAGE containing JUICE, that bears a warning label as
specified under ¶ 3-404.11(B) may not be served or offered for sale; P and
(3) UnPACKAGED JUICE that is prepared on the PREMISES for service or sale in a READY-TO-EAT form
shall be processed under a HACCP PLAN that contains the information specified under ¶¶ 8-
201.14(B) - (E) and as specified in 21 CFR Part 120 - HAZARD Analysis and CRITICAL CONTROL
POINT (HACCP) Systems, Subpart B Pathogen Reduction, 120.24 Process controls. P
(B) Pasteurized EGGS or EGG PRODUCTS shall be substituted for raw EGGS in the preparation of: P`
(1) FOODS such as Caesar salad, hollandaise or Béarnaise sauce, mayonnaise, meringue, EGGnog, ice
cream, and EGG-fortified BEVERAGES, P and
(2) Except as specified in ¶ (F) of this section, recipes in which more than one EGG is broken and
the EGGS are combined; P
(C) The following FOODS may not be served or offered for sale in a READY-TO-EAT form: P
72
(1) Raw animal FOODS such as raw FISH, raw-marinated FISH, raw MOLLUSCAN SHELLFISH, and steak
tartare, P
(2) A partially cooked animal FOOD such as lightly cooked FISH, rare MEAT, soft-cooked EGGS that are
made from raw EGGS, and meringue; P and
(3) Raw seed sprouts. P
(D) FOOD EMPLOYEES may not contact READY-TO-EAT FOOD as specified under ¶¶ 3-301.11(B) and (E). P
(E) Time only, as the public health control as specified under ¶ 3-501.19(D), may not be used for raw
EGGS; P
(F) Subparagraph (B)(2) of this section does not apply if:
(1) The raw EGGS are combined immediately before cooking for one CONSUMER'S serving at a single
meal, cooked as specified under Subparagraph 3-401.11(A)(1), and served immediately, such as
an omelet, soufflé, or scrambled EGGS;
(2) The raw EGGS are combined as an ingredient immediately before baking and the EGGS are
thoroughly cooked to a READY-TO-EAT form, such as a cake, muffin, or bread; or
(3) The preparation of the FOOD is conducted under a HACCP PLAN that:
(a) Identifies the FOOD to be prepared,
(b) Prohibits contacting READY-TO-EAT FOOD with bare hands,
(c) Includes specifications and practices that ensure:
(i.) Salmonella Enteritidis growth is controlled before and after cooking, and
(ii.) Salmonella Enteritidis is destroyed by cooking the EGGS according to the
temperature and time specified in Subparagraph 3-401.11(A)(2),
(d) Contains the information specified under ¶ 8-201.14(D) including procedures that:
(i.) Control cross contamination of READY-TO-EAT FOOD with raw EGGS, and
(ii.) Delineate cleaning and SANITIZATION procedures for FOOD-CONTACT SURFACES, and
(e) Describes the training program that ensures that the FOOD EMPLOYEE responsible for the
preparation of the FOOD understands the procedures to be used.
RE-SERVICE OF FOOD
(G) Except as specified in paragraph (H) of this section, FOOD may be re-served as specified under
Subparagraph 3-306.14(B)(1) and (2).
PROHIBITED RE-SERVICE OF FOOD
(H) FOOD may not be re-served under the following conditions:
(1) Any FOOD served to patients or clients who are under contact precautions in medical isolation or
quarantine, or protective environment isolation may not be re-served to others outside.
(2) Packages of FOOD from any patients, clients, or other CONSUMERS should not be re-served to PERSONS
in protective environment isolation.
73
CHAPTER 4 - EQUIPMENT, UTENSILS, AND LINENS
4-1 MATERIALS FOR CONSTRUCTION AND REPAIR
4-2 DESIGN AND CONSTRUCTION
4-3 NUMBERS AND CAPACITIES
4-4 LOCATION AND INSTALLATION
4-5 MAINTENANCE AND OPERATION
4-6 CLEANING OR EQUIPMENT AND UTENSILS
4-7 SANITIZATION OF EQUIPMENT AND UTENSILS
4-8 LAUNDERING
4-9 PROTECTION OF CLEAN ITEMS
4-1 MATERIALS FOR CONSTRUCTION AND REPAIR
SUBPARTS 4-101 Multiuse
4-102 Single-Service and Single-Use
MULTIUSE
4-101.11 CHARACTERISTICS
Materials that are used in the construction of UTENSILS and FOOD-CONTACT SURFACES of EQUIPMENT may not allow
the migration of deleterious substances or impart colors, odors, or tastes to FOOD and under normal use
conditions shall be; P
(A) Safe; P
(B) Durable, CORROSION-RESISTANT, and nonabsorbent;
(C) Sufficient in weight and thickness to withstand repeated WAREWASHING;
(D) Finished to have a SMOOTH, EASILY CLEANABLE surface; and
(E) Resistant to pitting, chipping, crazing, scratching, scoring, distortion, and decomposition.
4-101.12 CAST IRON, USE LIMITATION
(A) Except as specified in ¶¶ (B) and (C) of this section, cast iron may not be used for UTENSILS or FOOD-
CONTACT SURFACES of EQUIPMENT.
(B) Cast iron may be used as a surface for cooking.
(C) Cast iron may be used in UTENSILS for serving FOOD if the UTENSILS are used only as part of an
uninterrupted process from cooking through service.
4-101.13 LEAD, USE LIMITATION
(A) Ceramic, china, and crystal UTENSILS, and decorative UTENSILS such as hand painted ceramic or china
that are used in contact with FOOD shall be lead-free or contain levels of lead not exceeding the limits
of the following UTENSIL categories: P
Utensil Category Ceramic Article Description Maximum Lead MG/L
Beverage Mugs, Cups,
Pitchers Coffee Mugs 0.5
Large Hollowware
(excluding pitchers)
Bowls ≥ 1.1 Liter (1.16
Quart) 1
Small Hollowware
(excluding cups and mugs)
Bowls < 1.1 Liter (1.16
Quart) 2.0
Flat Tableware Plates, Saucers 3.0
(B) Pewter alloys containing lead in excess of 0.05% may not be used as a FOOD-CONTACT SURFACE. P
74
(C) Solder and flux containing lead in excess of 0.2% may not be used as a FOOD-CONTACT SURFACE.
4-101.14 COPPER, USE LIMITATION
(A) Except as specified in ¶ (B) of this section, copper and copper alloys such as brass may not be used in
contact with a FOOD that has a pH below 6 such as vinegar, fruit JUICE, or wine or for a fitting or tubing
installed between a backflow prevention device and a carbonator. P
(B) Copper and copper alloys may be used in contact with beer brewing ingredients that have a pH below 6
in the pre-fermentation and fermentation steps of a beer brewing operation such as a brewpub or
microbrewery.
4-101.15 GALVANIZED METAL, USE LIMITATION
Galvanized metal may not be used for UTENSILS or FOOD-CONTACT SURFACES of EQUIPMENT that are used in
contact with acidic FOOD. P
4-101.16 SPONGES, USE LIMITATION
Sponges may not be used in contact with cleaned and SANITIZED or in-use FOOD-CONTACT SURFACES.
4-101.17 WOOD, USE LIMITATION
(A) Except as specified in ¶¶ (B), (C), and (D) or this section, wood and wood wicker may not be used as a
FOOD-CONTACT SURFACE.
(B) Hard maple or an equivalently hard, close-grained wood may be used for:
(1) Cutting boards; cutting blocks; bakers' tables; and UTENSILS such as rolling pins, doughnut dowels,
salad bowls, and chopsticks; and
(2) Wooden paddles used in confectionery operations for pressure scraping kettles when manually
preparing confections at a temperature of 110°C (230°F) or above.
(C) Whole, uncut, raw fruits and vegetables, and nuts in the shell may be kept in the wood shipping
containers in which they were received, until the fruits, vegetables, or nuts are used.
(D) If the nature of the FOOD requires removal of rinds, peels, husks, or shells before consumption, the whole,
uncut, raw FOOD may be kept in:
(1) Untreated wood containers; or
(2) Treated wood containers if the containers are treated with a preservative that meets the
requirements specified in 21CFR178.380Preservatives for wood.
4-101.18 NONSTICK COATINGS, USE LIMITATION
Multiuse KITCHENWARE such as frying pans, griddles, sauce pans, cookie sheets, and waffle bakers that have a
perfluorocarbon resin coating shall be used with nonscoring or nonscratching UTENSILS and cleaning aids.
4-101.19 NONFOOD-CONTACT SURFACES
NonFOOD-CONTACT SURFACES of EQUIPMENT that are exposed to splash, spillage, or other FOOD soiling or that
require frequent cleaning shall be constructed of a CORROSION-RESISTANT, nonabsorbent, and SMOOTH material.
75
SINGLE-SERVICE AND SINGLE-USE
4-102.11 CHARACTERISTICS
Materials that are used to make SINGLE-SERVICE and SINGLE-USE ARTICLES:
(A) May not:
(1) Allow the migration of deleterious substances, P or
(2) Impart colors, odors, or tastes to FOOD; and
(B) Shall be:
(1) Safe, P and
(2) Clean.
4-2 DESIGN AND CONSTRUCTION
SUBPARTS 4-201 Durability and Strength
4-202 Cleanability
4-203 Accuracy
4-204 Functionality
4-205 Acceptability
DURABILITY AND STRENGTH
4-201.11 EQUIPMENT AND UTENSILS
EQUIPMENT and UTENSILS shall be designed and constructed to be durable and to retain their characteristic
qualities under normal use conditions.
4-201.12 FOOD TEMPERATURE MEASURING DEVICES
FOOD TEMPERATURE MEASURING DEVICES may not have sensors or stems constructed of glass, except that
thermometers with glass sensors or stems that are encased in a shatterproof coating such as candy
thermometers may be used. P
CLEANABILITY
4-202.11 FOOD-CONTACT SURFACES
(A) Multiuse FOOD-CONTACT SURFACES shall be:
(1) SMOOTH; Pf
(2) Free of breaks, open seams, cracks, chips, inclusions, pits, and similar imperfections; Pf
(3) Free of sharp internal angles, corners, and crevices; Pf
(4) Finished to have SMOOTH welds and joints; Pf and
(5) Except as specified in ¶ (B) of this section, accessible for cleaning and inspection by one of the
following methods:
(a) Without being disassembled, Pf
(b) By disassembling without the use of tools, Pf or
(c) By easy disassembling with the use of handheld tools commonly available to
maintenance and cleaning personnel such as screwdrivers, pliers, open-end wrenches,
and Allen wrenches. Pf
(6) Subparagraph (A)(5) of this section does not apply to cooking oil storage tanks, distribution lines
for cooking oils, or BEVERAGE syrup lines or tubes.
76
4-202.12 CIP EQUIPMENT
(A) CIP EQUIPMENT shall meet the characteristics specified under § 4-202.11 and shall be designed and
constructed so that:
(1) Cleaning and SANITIZING solutions circulate throughout a fixed system and contact all interior
FOOD-CONTACT SURFACES, Pf and
(2) The system is self-draining or capable of being completely drained of cleaning and SANITIZING
solutions; and
(B) CIP EQUIPMENT that is not designed to be disassembled for cleaning shall be designed with inspection
access points to ensure that all interior FOOD-CONTACT SURFACES throughout the fixed system are being
effectively cleaned.
4-202.13 “V” THREADS, USE LIMITATION
Except for hot oil cooking or filtering EQUIPMENT, "V" type threads may not be used on FOOD-CONTACT SURFACES.
4-202.14 HOT OIL FILTERING EQUIPMENT
Hot filtering EQUIPMENT shall meet the characteristics specified under § 4-202.11 or § 4-202.12 and shall be
readily accessible for filter replacement and cleaning of the filter.
4-202.15 CAN OPENERS
Cutting or piercing parts of can openers shall be readily removable for cleaning and for replacement.
4-202.16 NONFOOD-CONTACT SURFACES
NonFOOD-CONTACT SURFACES shall be free of unnecessary ledges, projections, and crevices, and designed and
constructed to allow easy cleaning and to facilitate maintenance.
4-202.17 KICK PLATES, REMOVABLE
Kick plates shall be designed so that the areas behind them are accessible for inspection and cleaning by
being:
(A) Removable by one the methods specified under ¶ 4-202.11(A)(5) or capable of being rotated open;
and
(B) Removable or capable of being rotated open without unlocking EQUIPMENT doors.
4-202.18 VENTILATION HOOD SYSTEMS, FILTERS
Filters or other grease extracting EQUIPMENT shall be designed to be readily removable for cleaning and
replacement if not designed to be cleaned in place.
ACCURACY
4-203.11 TEMPERATURE MEASURING DEVICES, FOOD
(A) FOOD TEMPERATURE MEASURING DEVICES that are scaled only in Celsius or dually scaled in Celsius and
Fahrenheit shall be accurate to ± 1°C in the intended range of use.
(B) FOOD TEMPERATURE MEASURING DEVICES that are scaled only in Fahrenheit shall be accurate to ± 2°F in the
intended range of use. Pf
4-203.12 TEMPERATURE MEASURING DEVICES, AMBIENT AIR AND WATER
(A) Ambient air and water TEMPERATURE MEASURING DEVICES that are scaled in Celsius or dually scaled in
Celsius and Fahrenheit shall be designed to be easily readable and accurate to ± 1.5°C in the intended
range of use. Pf
(B) Ambient air and water TEMPERATURE MEASURING DEVICES that are scaled only in Fahrenheit shall be
accurate to ± 3°F in the intended range of use. Pf
77
4-203.13 PRESSURE MEASURING DEVICES, MECHANICAL WAREWASHING EQUIPMENT
Pressure measuring devices that display the pressures in the water supply line for the fresh hot water
SANITIZING rinse shall have increments of 7 kilopascals (1 pound per square inch) or smaller and shall be
accurate to ±14 kilopascals (±2 pounds per square inch) in the range indicated on the manufacturer’s data
plate.
FUNCTIONALITY
4-204.11 VENTILATION HOOD SYSTEMS, DRIP PREVENTION
Exhaust ventilation hood systems in FOOD preparation and WAREWASHING areas including components such as
hoods, fans, guards, and ducting shall be designed to prevent grease or condensation from draining or
dripping onto FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES.
4-204.12 EQUIPMENT OPENINGS, CLOSURES AND DEFLECTORS
(A) A cover or lid for EQUIPMENT shall overlap the opening and be sloped to drain.
(B) An opening located within the top of a unit of EQUIPMENT that is designed for use with a cover or lid
shall be flanged upward at least 5 millimeters (two-tenths of an inch).
(C) Except as specified under ¶ (D) of this section, fixed piping, TEMPERATURE MEASURING DEVICE, rotary
shafts, and other parts extending into EQUIPMENT shall be provided with a watertight joint at the point
where the item enters the EQUIPMENT.
(D) If a watertight joint is not provided:
(1) The piping, TEMPERATURE MEASURING DEVICE, rotary shafts, and other parts extending through the
openings shall be equipped with an apron designed to deflect condensation, drips, and dust
from opening into the FOOD; and
(2) The opening shall be flanged as specified under ¶ (B) of this section.
4-204.13 DISPENSING EQUIPMENT, PROTECTION OF EQUIPMENT AND FOOD
In EQUIPMENT that dispenses or vends liquid FOOD or ice in unPACKAGED form:
(A) The delivery tube, chute, orifice, and splash surfaces directly above the container receiving the FOOD
shall be designed in a manner, such as with barriers, baffles, or drip aprons, so that drips from
condensation and splash are diverted from the opening of the container receiving the FOOD;
(B) The delivery tube, chute, and orifice shall be protected from manual contact such as by being
recessed;
(C) The delivery tube or chute and orifice of EQUIPMENT used to vend liquid FOOD or ice in unPACKAGED form
to self-service CONSUMERS shall be designed so that the delivery tube or chute and orifice are protected
from dust, insects, rodents, and other contamination by a self-closing door if the EQUIPMENT is:
(1) Located in an outside area that does not otherwise afford the protection of an enclosure against
the rain, windblown debris, insects, rodents, and other contaminants that are present in the
environment, or
(2) Available for self-service during hours when it is not under the full-time supervision of a FOOD
EMPLOYEE; and
(D) The dispensing EQUIPMENT actuating lever or mechanism and filling device of CONSUMER self-service
BEVERAGE dispensing EQUIPMENT shall be designed to prevent contact with the lip-contact surface of
glasses or cups that are refilled.
(E) Dispensing EQUIPMENT in which TIME/TEMPERATURE CONTROL FOR SAFETY FOOD in a homogenous liquid
form is maintained outside of the temperature control requirements as specified under § 3-501.16(A)
shall:
(1) Be specifically designed and equipped to maintain the commercial sterility of aseptically
PACKAGED FOOD in a homogenous liquid form for a specified duration from the time of opening
the packaging within the EQUIPMENT; P and
78
(2) Conform to the requirements for this EQUIPMENT as specified in NSF/ANSI 18-2006- Manual
FOOD and BEVERAGE Dispensing Equipment. P
4-204.14 VENDING MACHINE, VENDING STAGE CLOSURE
The dispensing compartment of a VENDING MACHINE including a machine that is designed to vend prePACKAGED
snack FOOD this is not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD such as chips, party mixes, and pretzels
shall be equipped with a self-closing door or cover if the machine is:
(A) Located in an outside area that does not otherwise afford the protection of an enclosure again the
rain, windblown debris, insects, rodents, and other contaminants that are present in the environment;
or
(B) Available for self-service during hours when it is not under the full-time supervision of a FOOD
EMPLOYEE.
4-204.15 BEARINGS AND GEAR BOXES, LEAK-PROOF
EQUIPMENT containing bearings and gears that require lubricants shall be designed and constructed so that
the lubricant cannot leak, drip, or be forced into FOOD or onto FOOD-CONTACT SURFACES.
4-204.16 BEVERAGE TUBING, SEPARATION
Except for cold plates that are constructed integrally with an ice storage bin, BEVERAGE tubing and cold-plate
BEVERAGE cooling devices may not be installed in contact with stored ice.
4-204.17 ICE UNITS, SEPARATION OF DRAINS
Liquid waste drain lines may not pass through an ice machine or ice storage bin.
4-204.18 CONDENSER UNIT, SEPARATION
If a condenser unit is an integral component of EQUIPMENT, the condenser unit shall be separated from the
FOOD and FOOD storage space by a dustproof barrier.
4-204.19 CAN OPENERS ON VENDING MACHINES
Cutting or piercing parts of can openers on VENDING MACHINES shall be protected from manual contact, dust,
insects, rodents, and other contamination.
4-204.110 MOLLUSCAN SHELLFISH TANKS
(A) Except as specified under ¶ (B) of this section, MOLLUSCAN SHELLFISH life support system display tanks
may not be used to store or display shellfish that are offered for human consumption and shall be
conspicuously marked so that it is obvious to the CONSUMER that the shellfish are for display only. P
(B) MOLLUSCAN SHELLFISH life-support system display tanks that are used to store or display shellfish that
are offered for human consumption shall be operated and maintained in accordance with a VARIANCE
granted by the REGULATORY AUTHORITY as specified in § 8-103.11 and a HACCP PLAN that: Pf
(1) Is submitted by the PERMIT HOLDER and APPROVED as specified under § 8-103.11, Pf and
(2) Ensures that:
(a) Water used with FISH other than MOLLUSCAN SHELLFISH does not flow into the molluscan
tank, Pf
(b) The safety and quality of the shellfish as they were received are not compromised by the
use of the tank, Pf and
(c) The identity of the source of the SHELLSTOCK is retained as specified under § 3-203.12. Pf
4-204.111 VENDING MACHINES, AUTOMATIC SHUTOFF
(A) A machine vending TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall have an automatic control that
prevents the machine from vending FOOD:
79
(1) If there is a power failure, mechanical failure, or other condition that results in an internal
machine temperature that cannot maintain FOOD temperatures as specified under Chapter 3; P
and
(2) If a condition specified under Subparagraph (A)(1)of this section occurs, until the machine is
serviced and restocked with FOOD that has been maintained at temperatures specified under
Chapter 3. P
(B) When the automatic shutoff within a machine vending TIME/TEMPERATURE CONTROL FOR SAFETY FOOD is
activated:
(1) In a refrigerated VENDING MACHINE, the ambient air temperature may not exceed 5°C (41°F) for
more than 30 minutes immediately after the machine is filled, serviced, or restocked; P or
(2) In a hot holding VENDING MACHINE, the ambient air temperature may not be less than 57°C
(135°F) for more than 120 minutes immediately after the machine is filled, serviced, or
restocked. P
4-204.112 TEMPERATURE MEASURING DEVICES
(A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE
shall be located to measure the air temperature or a simulated product temperature in the warmest
part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit.
(B) Except as specified in ¶ (C) of this section, cold or hot holding EQUIPMENT used for TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD shall be designed to include and shall be equipped with at least one integral
or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the
device's temperature display.
(C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE
MEASURING DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because
of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bain-
marie’s, steam tables, insulated FOOD transport containers, and salad bars.
(D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable.
(E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING
machines shall have a numerical scale, printed record, or digital readout in increments no greater
than 1°C (2°F) in the intended range of use. Pf
4-204.113 WAREWASHING MACHINE, DATA PLATE OPERATING SPECIFICATIONS
A WAREWASHING machine shall be provided with an easily accessible and readable data plate affixed to the
machine by the manufacturer that indicates the machine's design and operation specifications including the:
(A) Temperatures required for washing, rinsing, and SANITIZING;
(B) Pressure required for the fresh water SANITIZING rinse unless the machine is designed to use only a
pumped SANITIZING rinse; and
(C) Conveyor speed for conveyor machines or cycle time for stationary rack machines.
4-204.114 WAREWASHING MACHINES, INTERNAL BAFFLES
WAREWASHING machine was and rinse tanks shall be equipped with baffles, curtains, or other means to
minimize internal cross contamination of the solutions in wash and rinse tanks.
4-204.115 WAREWASHING MACHINES, TEMPERATURE MEASURING DEVICES
A WAREWASHING machine shall be equipped with a TEMPERATURE MEASURING DEVICE that indicates the
temperature of the water;
(A) In each wash and rinse tank; Pf and
(B) As the water enters the hot water SANITIZING final rinse manifold or in the chemical SANITIZING solution
tank.
80
4-204.116 MANUAL WAREWASHING EQUIPMENT, HEATERS AND BASKETS
If hot water is used for SANITIZATION in manual WAREWASHING operations, the SANITIZING compartment of the
sink shall be:
(A) Designed with an integral heating device that is capable of maintaining water at a temperature not
less than 77°C (171°F); Pf and
(B) Provided with a rack or basket to allow complete immersion of EQUIPMENT and UTENSILS into the hot
water. Pf
4-204.117 WAREWASHING MACHINES, AUTOMATIC DISPENSING OF DETERGENTS AND
SANITIZERS
A WAREWASHING machine that is installed after adoption of this Code by the REGULATORY AUTHORITY, shall be
equipped to:
(A) Automatically dispense detergents and SANITIZERS; Pf and
(B) Incorporate a visual means to verify that detergents and SANITIZERS are delivered or a visual or audible
alarm to signal if the detergents and SANITIZERS are not delivered to the respective washing and
SANITIZING cycles. Pf
4-204.118 WAREWASHING MACHINES, FLOW PRESSURE DEVICE
(A) WAREWASHING machines that provide a fresh hot water SANITIZING rinse shall be equipped with a
pressure gauge or similar device such as a transducer that measures and displays the water pressure
in the supply line immediately before entering the WAREWASHING machine; and
(B) If the flow pressure measuring device is upstream of the fresh hot water SANITIZING rinse control valve,
the device shall be mounted in a 6.4 millimeter or one-fourth inch Iron Pipe Size (IPS) valve.
(C) Paragraphs (A) and (B) of this section do not apply to a machine that uses only a pumped or recirculated
SANITIZING rinse.
4-204.119 WAREWASHING SINKS AND DRAINBOARDS, SELF-DRAINING
Sink and drainboards of WAREWASHING sinks and machines shall be self-draining.
4-204.120 EQUIPMENT COMPARTMENTS, DRAINAGE
EQUIPMENT compartments that are subject to accumulation of moisture due to conditions such as
condensation, FOOD or BEVERAGE drip, or water from melting ice shall be sloped to an outlet that allows
complete draining.
4-204.121 VENDING MACHINES, LIQUID WASTE PRODUCTS
(A) VENDING MACHINES designed to store BEVERAGES that are PACKAGED in containers made from paper
products shall be equipped with diversion devices and retention pans or drains for container leakage.
(B) VENDING MACHINES that dispense liquid FOOD in bulk shall be:
(1) Provided with an internally mounted waste receptacle for the collection of drip, spillage,
overflow, or other internal wastes; and
(2) Equipped with an automatic shutoff device that will place the machine out of operation before
the waste receptacle overflows.
(C) Shutoff devices specified under Subparagraph (B)(2) of this section shall prevent water or liquid FOOD
from continuously running if there is a failure of a flow control device in the water or liquid FOOD
system or waste accumulation that could lead to overflow of the waste receptacle.
4-204.122 CASE LOT HANDLING EQUIPMENT, MOVABILITY
Apparatuses, such as dollies, pallets, racks, and skids used to store and transport large quantities of PACKAGED
FOODS received from a supplier in a cased of overwrapped lot, shall be designed to be moved by hand or by
conveniently available apparatuses such as hand trucks and forklifts.
81
4-204.123 VENDING MACHINES DOORS AND OPENINGS
(A) VENDING MACHINE doors and access opening covers to FOOD and container storage spaces shall be tight-
fitting so that the space along the entire interface between the doors or covers and the cabinet of the
machine, if the doors or covers are in a closed position, is no greater than 1.5 millimeters or one-
sixteenth inch by:
(1) Being covered with louvers, screens, or materials that provide an equivalent opening of not
greater than 1.5 millimeters or one-sixteenth inch. Screening of 12 or more mesh to 2.5
centimeters (12 mesh to 1 inch) meets this requirement;
(2) Being effectively gasketed;
(3) Having interface surfaces that are at least 13 millimeters or one-half inch wide; or
(4) Jambs or surfaces used to form an L-shaped entry path to the interface.
(B) VENDING MACHINE service connection openings through an exterior wall of a machine shall be closed by
sealants, clamps, or grommets so that the openings are no larger than 1.5 millimeters or one-sixteenth
inch.
ACCEPTABILITY
4-205.10 FOOD EQUIPMENT, CERTIFICATION AND CLASSIFICATION
FOOD EQUIPMENT that is certified or classified for sanitation by an American National Standards Institute
(ANSI) - accredited certification program will be deemed to comply with Parts 4-1 and 4-2 of this chapter.
4-3 NUMBERS AND CAPACITIES
SUBPARTS 4-301 Equipment
4-302 Utensils, Temperature Measuring Devices, and Testing Devices
EQUIPMENT
4-301.11 COOLING, HEATING, AND HOLDING CAPACITIES
EQUIPMENT for cooling and heating FOOD, and holding cold and hot FOOD, shall be sufficient in number and
capability to provide FOOD temperatures as specified under Chapter 3. Pf
4-301.12 MANUAL WAREWASHING, SINK COMPARTMENT REQUIREMENTS
(A) Except as specified in ¶ (C) of this section, a sink with at least 3 compartments shall be provided for
manually washing, rinsing, and SANITIZING EQUIPMENT and UTENSILS. Pf
(B) Sink compartments shall be large enough to accommodate immersion of the largest EQUIPMENT and
UTENSILS. If EQUIPMENT or UTENSILS are too large for the WAREWASHING sink, a WAREWASHING machine or
alternative EQUIPMENT as specified in ¶ (C) of this section shall be used.
(C) Alternative manual WAREWASHING EQUIPMENT may be used when there are special cleaning needs or
constraints and its use is APPROVED. Alternative manual WAREWASHING EQUIPMENT may include:
(1) High-pressure detergent sprayers;
(2) Low- or line-pressure spray detergent foamers;
(3) Other task-specific cleaning EQUIPMENT;
(4) Brushes or other implements;
(5) 2-compartment sinks as specified under ¶¶ (D) and (E) of this section; or
(6) Receptacles that substitute for the compartments of a multicompartment sink.
(D) Before a 2-compartment sink is used:
82
(1) The PERMIT HOLDER shall have its use APPROVED; and
(2) The PERMIT HOLDER shall limit the number of KITCHENWARE items cleaned and SANITIZED in the 2-
compartment sink, and shall limit WAREWASHING to batch operations for cleaning KITCHENWARE
such as between cutting one type of raw MEAT and another or cleanup at the end of a shift, and
shall:
(a) Make up the cleaning and SANITIZING solutions immediately before use and drain them
immediately after use, and
(b) Use a detergent-SANITIZER to SANITIZE and apply the detergent-SANITIZER in accordance
with the manufacturer's label instructions and as specified under § 4-501.115, or
(c) Use a hot water SANITIZATION immersion step as specified under ¶ 4-603.16(C).
(E) A 2-compartment sink may not be used for WAREWASHING operations where cleaning and SANITIZING
solutions are used for a continuous or intermittent flow of KITCHENWARE or TABLEWARE in an ongoing
WAREWASHING process.
4-301.13 DRAINBOARDS
Drainboards, UTENSIL racks, or tables large enough to accommodate all soiled and cleaned items that may
accumulate during hours of operation shall be provided for necessary UTENSIL holding before cleaning and
after SANITIZING.
4-301.14 VENTILATION HOOD SYSTEMS, ADEQUACY
Ventilation hood systems and devices shall be sufficient in number and capacity to prevent grease or
condensation from collecting on walls and ceilings.
4-301.15 CLOTHES WASHERS AND DRYERS
(A) Except as specified in ¶ (B) of this section, if work clothes or LINENS are laundered on the PREMISES, a
mechanical clothes washer and dryer shall be provided and used.
(B) If on-PREMISES laundering is limited to wiping cloths intended to be used moist, or wiping cloths are air-
dried as specified under § 4-901.12, a mechanical clothes washer and dryer need not be provided.
UTENSILS, TEMPERATURE MEASURING DEVICES, AND TESTING DEVICES
4-302.11 UTENSILS, CONSUMER SELF-SERVICE
A FOOD dispensing UTENSIL shall be available for each container displayed at a CONSUMER self-service unit such
as a buffet or salad bar. Pf
4-302.12 FOOD TEMPERATURE MEASURING DEVICES
(A) FOOD TEMPERATURE MEASURING DEVICE shall be provided and readily accessible for use in ensuring
attainment and maintenance of FOOD temperatures as specified under Chapter 3. Pf
(B) A TEMPERATURE MEASURING DEVICE with a suitable small-diameter probe that is designed to measure the
temperature of thin masses shall be provided and readily accessible to accurately measure the
temperature in thin FOODS such as MEAT patties and FISH filets. Pf
4-302.13 TEMPERATURE MEASURING DEVICES, MANUAL AND MECHANICAL
WAREWASHING
(A) In manual WAREWASHING operations, a TEMPERATURE MEASURING DEVICE shall be provided and readily
accessible for frequent measuring the washing and SANITIZING temperatures. Pf
(B) In hot water mechanical WAREWASHING operations, an irreversible registering temperature indicator
shall be provided and readily accessible for measuring the UTENSIL surface temperature. Pf
83
4-302.14 SANITIZING SOLUTIONS, TESTING DEVICES
A test kit or other device that accurately measures the concentration in mg/L of SANITIZING solutions shall be
provided. Pf
4-4 LOCATION AND INSTALLATION
SUBPARTS 4-401 Location
4-402 Installation
LOCATION
4-401.11 EQUIPMENT, CLOTHES WASHERS AND DRYERS, AND STORAGE CABINETS,
CONTAMINATION PREVENTION
(A) Except as specified in ¶ (B) of this section, EQUIPMENT, a cabinet used for the storage of FOOD, or a
cabinet that is used to store cleaned and SANITIZED EQUIPMENT, UTENSILS, laundered LINENS, and SINGLE-
SERVICE and SINGLE-USE ARTICLES may not be located:
(1) In locker rooms;
(2) In toilet rooms;
(3) In garbage rooms;
(4) In mechanical rooms;
(5) Under sewer lines that are not shielded to intercept potential drips;
(6) Under leaking water lines including leaking automatic fire sprinkler heads or under lines on
which water has condensed;
(7) Under open stairwells; or
(8) Under other sources of contamination.
(B) A storage cabinet used for LINENS or SINGLE-SERVICE or SINGLE-USE ARTICLES may be stored in a locker
room.
(C) If a mechanical clothes washer or dryer is provided, it shall be located so that the washer or dryer is
protected from contamination and only where there is no exposed FOOD; clean EQUIPMENT, UTENSILS,
and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES.
INSTALLATION
4-402.11 FIXED EQUIPMENT, SPACING OR SEALING
(A) EQUIPMENT that is fixed because it is not EASILY MOVABLE shall be installed so that it is:
(1) Spaced to allow access for cleaning along the sides, behind, and above the EQUIPMENT,
(2) Spaced from adjoining EQUIPMENT, walls, and ceilings a distance of not more than 1 millimeter
or one thirty-second inch; or
(3) SEALED to adjoining EQUIPMENT or walls, if the EQUIPMENT is exposed to spillage or seepage.
(B) COUNTER-MOUNTED EQUIPMENT that is not EASILY MOVABLE shall be installed to allow cleaning of the
EQUIPMENT and areas underneath and around the EQUIPMENT by being:
(1) SEALED; or
(2) Elevated on legs as specified under ¶ 4-402.12(D).
84
4-402.12 FIXED EQUIPMENT, ELEVATION OR SEALING
(A) Except as specified in ¶¶ (B) and (C) of this section, floor-mounted EQUIPMENT that is not EASILY
MOVABLE shall be SEALED to the floor or elevated on legs that provide a 15 centimeter (6 inch) clearance
between the floor and the EQUIPMENT.
(B) If no part of the floor under the floor-mounted EQUIPMENT is more than 15 centimeters (6 inches) from the
point of cleaning access, the clearance space may be only 10 centimeters (4 inches).
(C) This section does not apply to display shelving units, display refrigeration units, and display freezer units
located in the CONSUMER shopping areas of a retail FOOD store, if the floor under the units is maintained
clean.
(D) Except as specified in ¶ (E) of this section, COUNTER-MOUNTED EQUIPMENT that is not EASILY MOVABLE shall
be elevated on legs that provide at least a 10 centimeter (4 inch) clearance between the table and the
EQUIPMENT.
(E) The clearance space between the table and COUNTER-MOUNTED EQUIPMENT may be:
(1) 7.5 centimeters (3 inches) if the horizontal distance of the table top under the EQUIPMENT is no
more than 50 centimeters (20 inches) from the point of access for cleaning; or
(2) 5 centimeters (2 inches) if the horizontal distance of the table top under the EQUIPMENT is no more
than 7.5 centimeters (3 inches) from the point of access for cleaning.
4-5 MAINTENANCE AND OPERATION
SUBPARTS 4-501 Equipment
4-502 Utensils and Temperature and Pressure Measuring Devices
EQUIPMENT
4-501.11 GOOD REPAIR AND PROPER ADJUSTMENT
(A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified
under Parts 4-1 and 4-2.
(B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact,
tight, and adjusted in accordance with manufacturer's specifications.
(C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal
fragments that can contaminate FOOD when the container is opened.
4-501.12 CUTTING SURFACES
Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if
they can no longer be effectively cleaned and SANITIZED, or discarded if they are not capable of being
resurfaced.
4-501.13 MICROWAVE OVENS
Microwave ovens shall meet the safety standards specified in 21 CFR 1030.10 Microwave ovens.
4-501.14 WAREWASHING EQUIPMENT, CLEANING FREQUENCY
A WAREWASHING machine; the compartments of sinks, basins, or other receptacles used for washing and
rinsing EQUIPMENT, UTENSILS, or raw FOODS, or laundering wiping cloths; and drainboards or other EQUIPMENT
used to substitute for drainboards as specified under § 4-301.13 shall be cleaned:
(A) Before use;
(B) Throughout the day at a frequency necessary to prevent recontamination of EQUIPMENT and UTENSILS
and to ensure that the EQUIPMENT performs its intended function; and
(C) If used, at least every 24 hours.
85
4-501.15 WAREWASHING MACHINES, MANUFACTURERS’ OPERATING INSTRUCTIONS
(A) A WAREWASHING machine and its auxiliary components shall be operated in accordance with the
machine's data plate and other manufacturer's instructions.
(B) A WAREWASHING machine's conveyor speed or automatic cycle times shall be maintained accurately
timed in accordance with manufacturer's specifications.
4-501.16 WAREWASHING SINKS, USE LIMITATION
(A) A WAREWASHING sink may not be used for handwashing as specified under § 2-301.15.
(B) If a WAREWASHING sink is used to wash wiping cloths, wash produce, or thaw FOOD, the sink shall be
cleaned as specified under § 4-501.14 before and after each time it is used to wash wiping cloths or
wash produce or thaw FOOD. Sinks used to wash or thaw FOOD shall be sanitized as specified under
Part 4-7 before and after using the sink to wash produce or thaw FOOD.
4-501.17 WAREWASHING EQUIPMENT, CLEANING AGENTS
When used for WAREWASHING, the wash compartment of a sink, mechanical warewasher, or wash receptacle
of alternative manual WAREWASHING EQUIPMENT as specified in ¶ 4-301.12(C), shall contain a wash solution of
soap, detergent, acid cleaner, alkaline cleaner, degreaser, abrasive cleaner, or other cleaning agent according
to the cleaning agent manufacturer label instructions. Pf
4-501.18 WAREWASHING EQUIPMENT, CLEAN SOLUTIONS
The wash, rinse, and SANITIZE solutions shall be maintained clean.
4-501.19 MANUAL WAREWASHING EQUIPMENT, WASH SOLUTION TEMPERATURE
The temperature of the wash solution in manual WAREWASHING EQUIPMENT shall be maintained at not less than
43°C (110°F) or the temperature specified on the cleaning agent manufacturer's label instructions. Pf
4-501.110 MECHANICAL WAREWASHING EQUIPMENT, WASH SOLUTION TEMPERATURE
(A) The temperature of the wash solution in spray type warewashers that use hot water to SANITIZE may
not be less than:
(1) For stationary rack, single temperature machine, 74°C (165°F); Pf
(2) For stationary rack, dual temperature machine, 66°C (150°F); Pf
(3) For a single tank, conveyor, dual temperature machine, 71°C (160°F); Pf
(4) For a multi-tank, conveyor, multi-temperature machine, 66°C (150°F); Pf
(B) The temperature of the wash solution in spray-type warewashers that use chemicals to SANITIZE may
not be less than 49°C (120°F). Pf
4-501.111 MANUAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION
TEMPERATURES
If immersion in hot water is used for SANITIZING in a manual operation, the temperature of the water shall be
maintained at 77°C (171°F) or above. P
4-501.112 MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION
TEMPERATURES
(A) Except as specified in ¶ (B) of this section, in a mechanical operation, the temperature of the fresh hot
water SANITIZING rinse as it enters the manifold may not be more than 90°C (194°F), or less than: Pf
(1) For a stationary rack, single temperature machine, 74°C (165°F); Pf or
(2) For all other machines, 82°C (180°F). Pf
(B) The maximum temperature specified under ¶ (A) of this section, does not apply to the high pressure and
temperature systems with wand-type, hand-held, spraying devices used for the in-place cleaning and
SANITIZING of EQUIPMENT such as MEAT saws.
86
4-501.113 MECHANICAL WAREWASHING EQUIPMENT, SANITIZATION PRESSURE
The flow pressure of the fresh hot water SANITIZING rinse in a WAREWASHING machine, as measured in the
water line immediately downstream or upstream from the fresh hot water SANITIZING rinse control valve,
shall be within the range specified on the machine manufacturer's data plate and may not be less than 35
kilopascals (5 pounds per square inch) or more than 200 kilopascals (30 pounds per square inch).
4-501.114 MANUAL AND MECHANICAL WAREWASHING EQUIPMENT, CHEMICAL
SANITIZATION – TEMPERATURE, PH, CONCENTRATION, AND HARDNESS
A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation at contact times
specified under ¶ 4-703.11(C) shall meet the criteria specified under § 7-204.11 SANITIZERS, Criteria, shall be
used in accordance with the EPA-registered label use instructions, P and shall be used as follows:
(A) A chlorine solution shall have a minimum temperature based on the concentration and pH of the
solution as listed in the following chart: P
Concentration Range
(mg/L)
Minimum Temperature
pH 10 or less
Minimum Temperature
pH 8 or less
25-49 49°C (120°F) 49°C (120°F)
50-99 38°C (100°F) 24°C (75°F)
100 13°C (55°F) 13°C (55°F)
(B) An iodine solution shall have a:
(1) Minimum temperature of 20°C (68°F), P
(2) pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies the
solution is effective, P and
(3) Concentration between 12.5 mg/L and 25 mg/L; P
(C) A quaternary ammonium compound solution shall:
(1) Have a minimum temperature of 24°C (75°F), P
(2) Have a concentration as specified under § 7-204.11 and as indicated by the manufacturer's use
directions included in the labeling, P and
(3) Be used only in water with 500 mg/L hardness or less or in water having a hardness no greater
than specified by the EPA-registered label use instructions; P
(D) If another solution of a chemical specified under ¶¶ (A) - (C) of this section is used, the PERMIT HOLDER
shall demonstrate to the REGULATORY AUTHORITY that the solution achieves SANITIZATION and the use of
the solution shall be APPROVED; P
(E) If a chemical SANITIZER other than chlorine, iodine, or a quaternary ammonium compound is used, it
shall be applied in accordance with the EPA-registered label use instructions; P and
(F) If a chemical SANITIZER is generated by a device located on-site at the FOOD ESTABLISHMENT, it shall be
used as specified in ¶¶ (A) - (D) of this section and shall be produced by a device that:
(1) Complies with regulation as specified in §§ 2(q)(1) and (12) of the Federal Insecticide,
Fungicide, and Rodenticide Act (FIFRA), P
(2) Complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling
Requirements, P
(3) Displays the EPA device manufacturing facility registration number on the device, Pf and
(4) Is operated and maintained in accordance with manufacturer’s instructions. Pf
87
4-501.115 MANUAL WAREWASHING EQUIPMENT, CHEMICAL SANITIZATION USING
DETERGENT-SANITIZERS
If a detergent-SANITIZER is used to SANITIZE in a cleaning and SANITIZING procedure where there is no distinct
water rinse between the washing and SANITIZING steps, the agent applied in the SANITIZING step shall be the
same detergent-SANITIZER that is used in the washing step.
4-501.116 WAREWASHING EQUIPMENT, DETERMINING CHEMICAL SANITIZER
CONCENTRATION
Concentration of the SANITIZING solution shall be accurately determined by using a test kit or other device. Pf
UTENSILS AND TEMPERATURE AND PRESSURE MEASURING DEVICES
4-502.11 GOOD REPAIR AND CALIBRATION
(A) UTENSILS shall be maintained in a state of repair or condition that complies with the requirements
specified under Parts 4-1 and 4-2 or shall be discarded.
(B) FOOD TEMPERATURE MEASURING DEVICES shall be calibrated in accordance with manufacturer's
specifications as necessary to ensure their accuracy. Pf
(C) Ambient air temperature, water pressure, and water TEMPERATURE MEASURING DEVICES shall be
maintained in good repair and be accurate within the intended range of use.
4-502.12 SINGLE-SERVICE AND SINGLE-USE ARTICLES, REQUIRED USE
A FOOD ESTABLISHMENT without facilities specified under Parts 4-6 and 4-7 for cleaning and SANITIZING
KITCHENWARE and TABLEWARE shall provide only SINGLE-USE KITCHENWARE, SINGLE-SERVICE ARTICLES, and SINGLE-
USE ARTICLES for use by FOOD EMPLOYEES and SINGLE-SERVICE ARTICLES for use by CONSUMERS. P
4-502.13 SINGLE-SERVICE AND SINGLE-USE ARTICLES, USE LIMITATION
(A) SINGLE-SERVICE and SINGLE-USE ARTICLES may not be reused.
(B) The bulk milk container dispensing tube shall be cut on the diagonal leaving no more than one inch
protruding from the chilled dispensing head.
4-502.14 SHELLS, USE LIMITATION
Mollusk and crustacea shells may not be used more than once as serving containers.
4-6 CLEANING OF EQUIPMENT AND UTENSILS
SUBPARTS 4-601 Objective
4-602 Frequency
4-603 Methods
OBJECTIVE
4-601.11 EQUIPMENT, FOOD-CONTACT SURFACES, NONFOOD-CONTACT SURFACES, AND
UTENSILS
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. Pf
(B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease
deposits and other soil accumulations.
(C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD
residue, and other debris.
88
FREQUENCY
4-602.11 EQUIPMENT FOOD-CONTACT SURFACES AND UTENSILS
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned:
(1) Except as specified in ¶ (B) of this section, before each use with a different type of raw animal
FOOD such as beef, FISH, lamb, pork, or POULTRY; P
(2) Each time there is a change from working with raw FOODs to working with READY-TO-EAT FOODS; P
(3) Between uses with raw fruits and vegetables and with TIME/TEMPERATURE CONTROL FOR SAFETY
FOOD; P
(4) Before using or storing a FOOD TEMPERATURE MEASURING DEVICE; P and
(5) At any time during the operation when contamination may have occurred. P
(B) Subparagraph (A)(1) of this section does not apply if the FOOD-CONTACT SURFACE or UTENSIL is in contact
with a succession of different types of raw MEAT and POULTRY each requiring a higher cooking
temperature as specified under § 3-401.11 than the previous type.
(C) Except as specified in ¶ (D) of this section, if used with TIME/TEMPERATURE CONTROL FOR SAFETY FOOD,
EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned throughout the day at least every 4
hours. P
(D) Surfaces of UTENSILS and EQUIPMENT contacting TIME/TEMPERATURE CONTROL FOR SAFETY FOOD may be cleaned
less frequently than every 4 hours if:
(1) In storage, containers of TIME/TEMPERATURE CONTROL FOR SAFETY FOOD and their contents are
maintained at temperatures specified under Chapter 3 and the containers are cleaned when they
are empty;
(2) UTENSILS and EQUIPMENT are used to prepare FOOD in a refrigerated room or area that is
maintained at one of the temperatures in the following chart and;
(a) The UTENSILS and EQUIPMENT are cleaned at the frequency in the following chart that
corresponds to the temperature; and
Temperature Cleaning Frequency
5.0°C or less
(41°F) or less 24 hours
>5.0°C - 7.2°C
(>41°F - 45°F) 20 hours
>7.2°C - 10.0°C
(>45°F - 50°F) 16 hours
>10.0°C - 12.8°C
(>50°F - 55°F) 10 hours
(b) The cleaning frequency based on the ambient temperature of the refrigerated room or
area is documented in the FOOD ESTABLISHMENT.
(3) Containers in serving situations such as salad bars, delis, and cafeteria lines hold READY-TO-EAT
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD that is maintained at the temperatures specified under
Chapter 3, are intermittently combined with additional supplies of the same FOOD that at the
required temperature, and the containers are cleaned at least every 24 hours;
(4) TEMPERATURE MEASURING DEVICES are maintained in contact with FOOD, such as when left in a
container of deli FOOD or in a roast, held at temperatures specified under Chapter 3;
(5) EQUIPMENT is used for storage of PACKAGED or unPACKAGED FOOD such as a reach-in refrigerator and
the EQUIPMENT is cleaned at a frequency necessary to preclude accumulation of soil residues;
(6) The cleaning schedule is APPROVED based on consideration of:
89
(a) Characteristics of the EQUIPMENT and its use,
(b) The type of FOOD involved,
(c) The temperature at which the FOOD is maintained during the operation and the potential
for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms
that are capable of causing foodborne disease; or
(7) In-use UTENSILS are intermittently stored in a container of water in which the water is maintained
at 57°C (135°F) or more and the UTENSILS and container are cleaned at least every 24 hours or at a
frequency necessary to preclude accumulation of soil residues.
(E) Except when dry cleaning methods are used as specified under § 4-603.11, surfaces of UTENSILS and
EQUIPMENT contacting FOOD that is not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD shall be cleaned:
(1) At any time when contamination may have occurred;
(2) At least every 24 hours for iced teas dispensers and CONSUMER self-service UTENSILS such as
tongs, scoops, or ladles;
(3) Before restocking CONSUMER self-service EQUIPMENT and UTENSILS such as condiment dispensers
and display containers; and
(4) In EQUIPMENT such as ice bins and BEVERAGE dispensing nozzles and enclosed components of
EQUIPMENT such as ice makers, cooking oil storage tanks and distribution lines, BEVERAGE and
syrup dispensing lines or tubes, coffee bean grinders, and water VENDING EQUIPMENT;
(a) At a frequency specified by the manufacturer, or
(b) Absent manufacturer specifications, at a frequency necessary to preclude accumulation
of soil or mold.
4-602.12 COOKING AND BAKING EQUIPMENT
(A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours.
This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in ¶ 4-
602.11(D)(6).
(B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the
manufacturer's recommended cleaning procedure.
4-602.13 NONFOOD-CONTACT SURFACES
NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation
of soil residues.
METHODS
4-603.11 DRY CLEANING
(A) If used, dry cleaning methods such as brushing, scraping, and vacuuming shall contact only surfaces
that are soiled with dry FOOD residues that are not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD.
(B) Cleaning EQUIPMENT used in dry cleaning FOOD-CONTACT SURFACES may not be used for any other
purpose.
4-603.12 PRECLEANING
(A) FOOD debris on EQUIPMENT and UTENSILS shall be scraped over a waste disposal unit or garbage
receptacle or shall be removed in a WAREWASHING machine with a prewash cycle.
(B) If necessary for effective cleaning, UTENSILS and EQUIPMENT shall be preflushed, presoaked, or scrubbed
with abrasives.
4-603.13 LOADING OF SOILED ITEMS, WAREWASHING MACHINES
Soiled items to be cleaned in a WAREWASHING machine shall be loaded into racks, trays, or baskets or onto
conveyors in a position that:
90
(A) Exposes the items to the unobstructed spray from all cycles; and
(B) Allows the items to drain.
4-603.14 WET CLEANING
(A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be effectively washed to remove or completely
loosen soils by using the manual or mechanical means necessary such as the application of detergents
containing wetting agents and emulsifiers; acid, alkaline, or abrasive cleaners; hot water; brushes;
scouring pads; high-pressure sprays; or ultrasonic devices.
(B) The washing procedures selected shall be based on the type and purpose of the EQUIPMENT or UTENSIL,
and on the type of soil to be removed.
4-603.15 WASHING, PROCEDURES FOR ALTERNATIVE MANUAL WAREWASHING
EQUIPMENT
If washing in sink compartments or a WAREWASHING machine is impractical such as when the EQUIPMENT is
fixed or the UTENSILS are too large, washing shall be done by using alternative manual WAREWASHING
EQUIPMENT as specified in ¶ 4-301.12(C) in accordance with the following procedures:
(A) EQUIPMENT shall be disassembled as necessary to allow access of the detergent solution to all parts;
(B) EQUIPMENT components and UTENSILS shall be scrapped or rough cleaned to remove FOOD particle
accumulation; and
(C) EQUIPMENT and UTENSILS shall be washed as specified under ¶ 4-603.14(A).
4-603.16 RINSING PROCEDURES
Washed UTENSILS and EQUIPMENT shall be rinsed so that abrasives are removed and cleaning chemicals are
removed or diluted through the use of water or a detergent-SANITIZER solution by using one of the following
procedures:
(A) Use of a distinct, separate rinse after washing and before SANITIZING if using:
(1) A 3-compartment sink,
(2) Alternative manual WAREWASHING EQUIPMENT equivalent to a 3-compartment sink as specified in
¶ 4-301.12(C), or
(3) A 3-step washing, rinsing, and SANITIZING procedure in a WAREWASHING system for CIP
EQUIPMENT;
(B) Use of a detergent-SANITIZER as specified under § 4-501.115 if using:
(1) Alternative WAREWASHING EQUIPMENT as specified in ¶ 4-301.12(C) that is APPROVED for use with
a detergent-SANITIZER, or
(2) A WAREWASHING system for CIP EQUIPMENT.
(C) Use of a nondistinct water rinse that is integrated in the hot water SANITIZATION step of a 2-
compartment sink operation;
(D) If using a WAREWASHING machine that does not recycle the SANITIZING solution as specified under ¶ (E)
of this section, or alternative manual WAREWASHING EQUIPMENT such as sprayers, use of a nondistinct
water rinse that is:
(1) Integrated in the application of the SANITIZING solution, and
(2) Wasted immediately after each application; or
(E) If using a WAREWASHING machine that recycles the SANITIZING solution for use in the next wash cycle, use
of nondistinct water rinse that is integrated in the application of the SANITIZING solution.
91
4-7 SANITATION OF EQUIPMENT AND UTENSILS
SUBPARTS 4-701 Objective
4-702 Frequency
4-703 Methods
OBJECTIVE
4-701.10 FOOD-CONTACT SURFACES AND UTENSILS
EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED.
FREQUENCY
4-702.11 BEFORE USE AFTER CLEANING
UTENSILS and FOOD-CONTACT SURFACES of EQUIPMENT shall be SANITIZED before use after cleaning. P
METHODS
4-703.11 HOT WATER AND CHEMICAL
After being cleaned, EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED in:
(A) Hot water manual operations by immersion for at least 30 seconds and as specified under § 4-
501.111; P
(B) Hot water mechanical operations by being cycled through EQUIPMENT that is set up as specified under
§§ 4-501.15, 4-501.112, and 4-501.113 and achieving a UTENSIL surface temperature of 71°C (160°F)
as measured by an irreversible registering temperature indicator; P or
(C) Chemical manual or mechanical operations, including the application of SANITIZING chemicals by
immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified
under § 4-501.114. Contact times shall be consistent with those on EPA-registered label use
instructions by providing:
(1) Except as specified under Subparagraph (C)(2) of this section, a contact time of at least 10
seconds for a chlorine solution specified under ¶ 4-501.114(A), P
(2) A contact time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less
and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least
24°C (75°F), P
(3) A contact time of at least 30 seconds for other chemical sanitizing solutions, P or
(4) A contact time used in relationship with a combination of temperature, concentration, and pH
that, when evaluated for efficacy, yields SANITIZATION as defined in 1-201.10(B). P
4-8 LAUNDERING
SUBPARTS 4-801 Objective
4-802 Frequency
4-803 Methods
OBJECTIVE
4-801.11 CLEAN LINENS
Clean LINENS shall be free from FOOD residues and other soiling matter.
92
FREQUENCY
4-802.11 SPECIFICATIONS
(A) LINENS that do not come in direct contact with FOOD shall be laundered between operations if they
become wet, sticky, or visibly soiled.
(B) Cloth gloves used as specified in ¶ 3-304.15(D) shall be laundered before being used with a different
type of raw animal FOOD such as beef, FISH, lamb, pork or POULTRY.
(C) LINENS that are used as specified under § 3-304.13 and cloth napkins shall be laundered between each
use.
(D) Wet wiping cloths shall be laundered daily.
(E) Dry wiping cloths shall be laundered as necessary to prevent contamination of FOOD and clean serving
UTENSILS.
METHODS
4-803.11 STORAGE OF SOILED LINENS
Soiled LINENS shall be kept in clean, nonabsorbent receptacles or clean, washable laundry bags and stored
and transported to prevent contamination of FOOD, clean EQUIPMENT, clean UTENSILS, and SINGLE-SERVICE and
SINGLE-USE ARTICLES.
4-803.12 MECHANICAL WASHING
(A) Except as specified in ¶ (B) of this section, LINENS shall be mechanically washed.
(B) In FOOD ESTABLISHMENTS in which only wiping cloths are laundered as specified in ¶ 4-301.15(B), the
wiping cloths may be laundered in a mechanical washer, sink designated only for laundering wiping
cloths, or a WAREWASHING or FOOD preparation sink that is cleaned as specified under § 4-501.14.
4-803.13 USE OF LAUNDRY FACILITIES
(A) Except as specified in ¶ (B) of this section, laundry facilities on the PREMISES of a FOOD ESTABLISHMENT
shall be used only for the washing and drying of items used in the operation of the establishment.
(B) Separate laundry facilities located on the PREMISES for the purpose of general laundering such as for
institutions providing boarding and lodging may also be used for laundering FOOD ESTABLISHMENT
items.
4-9 PROTECTION OF CLEAN ITEMS
SUBPARTS 4-901 Drying
4-902 Lubricating and Reassembling
4-903 Storing
4-904 Preventing Contamination
DRYING
4-901.11 EQUIPMENT AND UTENSILS, AIR-DRYING REQUIRED
After cleaning and SANITIZING, EQUIPMENT and UTENSILS:
(A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR
180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations
(FOOD-CONTACT SURFACE SANITIZING SOLUTIONS), before contact with FOOD; and
(B) May not be cloth dried except that UTENSILS that have been air-dried may be polished with cloths that
are maintained clean and dry.
93
4-901.12 WIPING CLOTHS, AIR-DRYING LOCATIONS
Wiping cloths laundered in a FOOD ESTABLISHMENT that does not have a mechanical clothes dryer as specified
in ¶ 4-301.15(B) shall be air-dried in a location and in a manner that prevents contamination of FOOD,
EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES and the wiping cloths. This section
does not apply if wiping cloths are stored after laundering in a SANITIZATION solution as specified under § 4-
501.114.
LUBRICATING AND REASSEMBLING
4-902.11 FOOD-CONTACT SURFACES
Lubricants as specified under § 7-205.11 shall be applied to FOOD-CONTACT SURFACES that require lubrication in
a manner that does not contaminate FOOD-CONTACT SURFACES.
4-902.12 EQUIPMENT
EQUIPMENT shall be reassembled so that FOOD-CONTACT SURFACES are not contaminated.
STORING
4-903.11 EQUIPMENT, UTENSILS, LINENS, AND SINGLE-SERVICE AND SINGLE-USE ARTICLES
(A) Except as specified in ¶ (D) of this section, cleaned EQUIPMENT and UTENSILS, laundered LINENS, and
SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored:
(1) In a clean, dry location;
(2) Where they are not exposed to splash, dust, or other contamination; and
(3) At least 15 cm (6 inches) above the floor.
(B) Clean EQUIPMENT and UTENSILS shall be stored as specified under ¶ (A) of this section and shall be
stored:
(1) In a self-draining position that allows air drying; and
(2) Covered or inverted.
(C) SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored as specified under ¶ (A) of this section and shall
be kept in the original protective PACKAGE or stored by using other means that afford protection from
contamination until used.
(D) Items that are kept in closed PACKAGES may be stored less than 15 cm (6 inches above the floor on dollies,
pallets, racks, and skids that are designed as specified under § 4-204.122.
4-903.12 PROHIBITIONS
(A) Except as specified in ¶ (B) of this section, cleaned and SANITIZED EQUIPMENT, UTENSILS, laundered LINENS,
and SINGLE-SERVICE and SINGLE-USE ARTICLES may not be stored:
(1) In locker rooms;
(2) In toilet rooms:
(3) In garbage rooms:
(4) In mechanical rooms;
(5) Under sewer lines that are not shielded to intercept potential drips;
(6) Under leaking water lines including leaking automatic fire sprinkler heads or under lines on
which water has condensed;
(7) Under open stairwells; or
(8) Under other sources of contamination.
94
(B) Laundered LINENS and SINGLE-SERVICE and SINGLE-USE ARTICLES that are PACKAGED or in a facility such as a
cabinet may be stored in a locker room.
PREVENTING CONTAMINATION
4-904.11 KITCHEN AND TABLEWARE
(A) SINGLE-SERVICE and SINGLE-USE ARTICLES and cleaned and SANITIZED UTENSILS shall be handled, displayed,
and dispensed so that contamination of FOOD- and lip-contact surfaces is prevented.
(B) Knives, forks, and spoons that are not prewrapped shall be presented so that only the handles are
touched by EMPLOYEES and by CONSUMERS if CONSUMER self-service is provided.
(C) Except as specified under ¶ (B) of this section, SINGLE-SERVICE ARTICLES that are intended for FOOD- or
lip-contact shall be furnished for CONSUMER self-service with the original individual wrapper intact or
from an APPROVED dispenser.
4-904.12 SOILED AND CLEAN TABLEWARE
Soiled TABLEWARE shall be removed from CONSUMER eating and drinking areas and handles so that clean
TABLEWARE is not contaminated.
4-904.13 PRESET TABLEWARE
(A) Except as specified in (B) of this section, TABLEWARE that is preset shall be protected from
contamination by being wrapped, covered, or inverted.
(B) Preset TABLEWARE may be exposed if:
(1) Unused settings are removed when a CONSUMER is seated; or
(2) Settings not removed when a CONSUMER is seated are cleaned and SANITIZED before further use.
4-904.14 RINSING EQUIPMENT AND UTENSILS AFTER CLEANING AND SANITIZING
After being cleaned and SANITIZED, EQUIPMENT and UTENSILS shall not be rinsed before air drying or use unless:
(A) The rinse is applied directly from a potable water supply by a WAREWASHING machine that is
maintained and operated as specified under Subparts 4-204 and 4-501; and
(B) The rinse is applied only after the EQUIPMENT and UTENSILS have been SANITIZED by the application of
hot water or by the application of a chemical SANITIZER solution whose EPA-registered label use
instructions call for rinsing off the SANITIZER after it is applied in a commercial WAREWASHING machine.
95
CHAPTER 5 - WATER, PLUMBING, AND WASTE
5-1 WATER
5-2 PLUMBING SYSTEM
5-3 MOBILE WATER TANK AND MOBILE FOOD ESTABLISHMENT WATER TANK
5-4 SEWAGE, OTHER LIQUID WASTE, AND RAINWATER
5-5 REFUSE, RECYCLABLES, AND RETURNABLES
5-1 WATER
SUBPARTS 5-101 Source
5-102 Quality
5-103 Quantity and Availability
5-104 Distribution, Delivery, and Retention
SOURCE
5-101.11 APPROVED SYSTEM
DRINKING WATER shall be obtained from an APPROVED source that is:
(A) A PUBLIC WATER SYSTEM; P or
(B) A nonPUBLIC WATER SYSTEM that is constructed, maintained, and operated according to LAW. P
5-101.12 SYSTEM FLUSHING AND DISINFECTION
A DRINKING WATER system shall be flushed and disinfected before being placed in service after construction,
repair, or modification and after an emergency situation, such as a flood, that may introduce contaminants to
the system. P
5-101.13 BOTTLED DRINKING WATER
BOTTLED DRINKING WATER used or sold in a FOOD ESTABLISHMENT shall be obtained from APPROVED sources in
accordance with 21 CFR 129 - Processing and Bottling of BOTTLED DRINKING WATER. P
QUALITY
5-102.11 STANDARDS
Except as specified under § 5-102.12;
(A) Water from a PUBLIC WATER SYSTEM shall meet 40 CFR 141 - National Primary DRINKING WATER
Regulations and state DRINKING WATER quality standards; P and
(B) Water from a NONPUBLIC WATER SYSTEM shall meet state DRINKING WATER quality standards. P
5-102.12 NONDRINKING WATER
(A) A nonDRINKING WATER supply shall be used only if its use is APPROVED. P
(B) NonDRINKING WATER shall be used only for nonculinary purposes such as air conditioning, nonFOOD
EQUIPMENT cooling, and fire protection. P
5-102.13 SAMPLING
Except when used as specified under § 5-102.12, water from a nonPUBLIC WATER SYSTEM shall be sampled and
tested at least annually and as required by state water quality regulations. Pf
5-102.14 SAMPLE REPORT
The most recent sample report for the nonPUBLIC WATER SYSTEM shall be retained on file in the FOOD
ESTABLISHMENT or the report shall be maintained as specified by state water quality regulations.
96
QUANTITY AND AVAILABILITY
5-103.11 CAPACITY
(A) The water source and system shall be of sufficient capacity to meet the peak water demands of the
FOOD ESTABLISHMENT. Pf
(B) Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands
throughout the FOOD ESTABLISHMENT. Pf
5-103.12 PRESSURE
Water under pressure shall be provided to all fixtures, EQUIPMENT, and nonFOOD EQUIPMENT that are required
to use water except that water supplied as specified under ¶¶ 5-104.12(A) and (B) to a TEMPORARY FOOD
ESTABLISHMENT or in response to a temporary interruption of a water supply need not be under pressure. Pf
DISTRIBUTION, DELIVERY, AND RETENTION
5-104.11 SYSTEM
Water shall be received from the source through the use of:
(A) An APPROVED public water main; Pf or
(B) One or more of the following that shall be constructed, maintained, and operated according to LAW: Pf
(1) Nonpublic water main, water pumps, pipes, hoses, connections, and other appurtenances, Pf
(2) Water transport vehicles, Pf or
(3) Water containers. Pf
5-104.12 ALTERNATIVE WATER SUPPLY
Water meeting the requirements specified under Subparts 5-101, 5-102, 5-103 shall be made available for a
mobile facility, for a TEMPORARY FOOD ESTABLISHMENT without a permanent water supply, and for a FOOD
ESTABLISHMENT with a temporary interruption of its water supply through:
(A) A supply of containers of commercially BOTTLED DRINKING WATER; Pf
(B) One or more closed portable water containers; Pf
(C) An enclosed vehicular water tank; Pf
(D) An on-PREMISES water storage tank; Pf or
(E) Piping, tubing, or hoses connected to an adjacent APPROVED source. Pf
5-2 PLUMBING SYSTEM
SUBPARTS 5-201 Materials
5-202 Design, Construction, and Installation
5-203 Numbers and Capacities
5-204 Location and Placement
5-205 Operation and Maintenance
MATERIALS
5-201.11 APPROVED
(A) A PLUMBING SYSTEM and hoses conveying water shall be constructed and repaired with APPROVED
materials according to LAW. P
(B) A water filter shall be made of SAFE MATERIALS. P
97
DESIGN, CONSTRUCTION, AND INSTALLATION
5-202.11 APPROVED SYSTEM AND CLEANABLE FIXTURES
(A) A PLUMBING SYSTEM shall be designed, constructed, and installed according to LAW. P
(B) A PLUMBING FIXTURE such as a HANDWASHING SINK, toilet, or urinal shall be EASILY CLEANABLE.
5-202.12 HANDWASHING SINK, INSTALLATION
(A) A HANDWASHING SINK shall be equipped to provide water at a temperature of at least 38°C (100°F)
through a mixing valve or combination faucet. Pf
(B) A steam mixing valve may not be used at a HANDWASHING SINK.
(C) A self-closing, slow-closing, or metering faucet shall provide a flow of water for at least 15 seconds
without the need to reactivate the faucet.
(D) An automatic handwashing facility shall be installed in accordance with manufacturer's instructions.
5-202.13 BACKFLOW PREVENTION, AIR GAP
An air gap between the water supply inlet and the flood level rim of the PLUMBING FIXTURE, EQUIPMENT, or
nonFOOD EQUIPMENT shall be at least twice the diameter of the water supply inlet and may not be less that
25mm (1 inch). P
5-202.14 BACKFLOW PREVENTION DEVICE, DESIGN STANDARD
A backflow or backsiphonage prevention device installed on a WATER SUPPLY SYSTEM shall meet American
Society of Sanitary Engineering (A.S.S.E.) standards for construction, installation, maintenance, inspection,
and testing for that specific application and type of device.
5-202.15 CONDITIONING DEVICE, DESIGN
A water filter, screen, and other water conditioning device installed on water lines shall be designed to
facilitate disassembly for periodic servicing and cleaning. A water filter element shall be of the replaceable
type.
NUMBERS AND CAPACITIES
5-203.11 HANDWASHING SINKS AND HANDWASHING FACILITIES
(A) Except as specified in ¶¶ (B) and (C) of this section, at least 1 HANDWASHING SINK, a number of
HANDWASHING SINKS necessary for their convenient use by EMPLOYEES in areas specified under § 5-
204.11, and not fewer than the number of HANDWASHING SINKS required by LAW shall be provided. Pf
(B) If APPROVED and capable of removing the types of soils encountered in the FOOD operations involved,
automatic handwashing facilities may be substituted for HANDWASHING SINKS in a FOOD ESTABLISHMENT that
has at least 1 HANDWASHING SINK.
(C) If APPROVED, when FOOD exposure is limited and HANDWASHING SINKS are not conveniently available, such as
in some mobile or TEMPORARY FOOD ESTABLISHMENTS or at some VENDING MACHINE LOCATIONS, EMPLOYEES may
use chemically treated towelettes for handwashing.
5-203.12 TOILETS AND URINALS
At least 1 toilet and not fewer than the toilets required by LAW shall be provided. If authorized by LAW and
urinals are substituted for toilets, the substitution shall be done as specified in LAW.
5-203.13 SERVICE SINK
(A) At least 1 service sink or 1 curbed cleaning facility equipped with a floor drain shall be provided and
conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal
of mop water and similar liquid waste.
(B) Toilets and urinals may not be used as a service sink for the disposal of mop water and similar liquid
waste.
98
5-203.14 BACKFLOW PREVENTION DEVICE, WHEN REQUIRED
A PLUMBING SYSTEM shall be installed to preclude backflow of a solid, liquid, or gas contaminant into the water
supply system at each point of use at the FOOD ESTABLISHMENT, including on a hose bibb if a hose is attached or
on a hose bibb if a hose is not attached and backflow prevention is required by LAW, by:
(A) Providing an air gap as specified under § 5-202.13; P or
(B) Installing an APPROVED backflow prevention device as specified under § 5-202.14. P
5-203.15 BACKFLOW PREVENTION DEVICE, CARBONATOR
(A) If not provided with an air gap as specified under § 5-202.13,a dual check valve with an intermediate
vent preceded by a screen of not less than 100 mesh to 25.4 mm (100 mesh to 1 inch) shall be
installed upstream from a carbonating device and downstream from any copper in the water supply
line. P
(B) A dual check valve attached to the carbonator need not be of the vented type if an air gap or vented
backflow prevention device has been otherwise provided as specified under ¶ (A) of this section.
LOCATION AND PLACEMENT
5-204.11 HANDWASHING SINKS
A HANDWASHING SINK shall be located:
(A) To allow convenient use by EMPLOYEES in FOOD preparation, FOOD dispensing, and WAREWASHING areas, Pf
and
(B) In, or immediately adjacent to, toilet rooms. Pf
5-204.12 BACKFLOW PREVENTION DEVICE, LOCATION
A backflow prevention device shall be located so that it may be serviced or maintained.
5-204.13 CONDITIONING DEVICE, LOCATION
A water filter, screen, and other water conditioning device installed on water lines shall be located to
facilitate disassembly for periodic servicing and cleaning.
OPERATION AND MAINTENANCE
5-205.11 USING A HANDWASHING SINK
(A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use. Pf
(B) A HANDWASHING SINK may not be used for purposes other than handwashing. Pf
(C) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. Pf
5-205.12 PROHIBITING A CROSS CONNECTION
(A) A PERSON may not create a cross connection by connecting a pipe or conduit between the DRINKING
WATER SYSTEM and a nonDRINKING WATER SYSTEM or a water system of unknown quality. P
(B) The piping of a nonDRINKING WATER SYSTEM shall be durably identified so that it is readily
distinguishable from piping that carries DRINKING WATER. Pf
5-205.13 SCHEDULING INSPECTION AND SERVICE FOR A WATER SYSTEM DEVICE
A device such as a water treatment device or backflow preventer shall be scheduled for inspection and
service, in accordance with manufacturer's instructions and as necessary to prevent device failure based on
local water conditions, and records demonstrating inspection and service shall be maintained by the PERSON
IN CHARGE. Pf
5-205.14 WATER RESERVOIR OF FOGGING DEVICES, CLEANING
(A) A reservoir that is used to supply water to a device such as a produce fogger shall be:
99
(1) Maintained in accordance with manufacturer's specifications; P and
(2) Cleaned in accordance with manufacturer's specifications or according to the procedures
specified under ¶ (B) of this section, whichever is more stringent. P
(B) Cleaning procedures shall include at least the following steps and shall be conducted at least once a
week:
(1) Draining and complete disassembly of the water and aerosol contact parts; P
(2) Brush-cleaning the reservoir, aerosol tubing, and discharge nozzles with a suitable detergent
solution; P
(3) Flushing the complete system with water to remove the detergent solution and particulate
accumulation; P and
(4) Rinsing by immersing, spraying, or swabbing the reservoir, aerosol tubing, and discharge
nozzles with at least 50 mg/L hypochlorite solution. P
5-205.15 SYSTEM MAINTAINED IN GOOD REPAIR
A PLUMBING SYSTEM shall be:
(A) Repaired according to LAW; P and
(B) Maintained in good repair.
5-3 MOBILE WATER TANK AND MOBILE FOOD ESTABLISHMENT WATER TANK
SUBPARTS 5-301 Materials
5-302 Design, Construction, and Installation
5-303 Numbers and Capacities
5-304 Location and Placement
MATERIALS
5-301.11 APPROVED
Materials that are used in the construction of a mobile water tank, MOBILE FOOD ESTABLISHMENT water tank, and
appurtenances shall be:
(A) Safe; P
(B) Durable, CORROSION-RESISTANT, and nonabsorbent; and
(C) Finished to have a SMOOTH, EASILY CLEANABLE surface.
DESIGN AND CONSTRUCTION
5-302.11 ENCLOSED SYSTEM, SLOPED TO DRAIN
A mobile water tank shall be:
(A) Enclosed from the filling inlet to the discharge outlet; and
(B) Sloped to an outlet that allows complete drainage of the tank.
5-302.12 INSPECTION AND CLEANING PORT, PROTECTED AND SECURED
If a water tank is designed with an access port for inspection and cleaning, the opening shall be in the top of
the tank and:
(A) Flanged upward at least 13 mm (one-half inch); and
(B) Equipped with a port cover assembly that is:
(1) Provided with a gasket and a device for securing the cover in place, and
100
(2) Flanged to overlap the opening and sloped to drain.
5-302.13 “V” TYPE THREADS, USE LIMITATION
A fitting with "V" type threads on a water tank inlet or outlet shall be allowed only when a hose is
permanently attached.
5-302.14 TANK VENT, PROTECTED
If provided, a water tank vent shall terminate in a downward direction and shall be covered with:
(A) 16 mesh to 25.4 mm (16 mesh to 1 inch) screen or equivalent when the vent is in a protected area; or
(B) A protective filter when the vent is in an area that is not protected from windblown dirt and debris.
5-302.15 INLET AND OUTLET, SLOPED TO DRAIN
(A) A water tank and its inlet and outlet shall be sloped to drain.
(B) A water tank inlet shall be positioned so that it is protected from contaminants such as waste
discharge, road dust, oil, or grease.
5-302.16 HOSE, CONSTRUCTION AND IDENTIFICATION
A hose used for conveying DRINKING WATER from a water tank shall be:
(A) Safe; P
(B) Durable, CORROSION-RESISTANT, and nonabsorbent;
(C) Resistant to pitting, chipping, crazing, scratching, scoring, distortion, and decomposition;
(D) Finished with a SMOOTH interior surface; and
(E) Clearly and durably identified as to its use if not permanently attached.
NUMBERS AND CAPACITIES
5-303.11 FILTER, COMPRESSED AIR
A filter that does not pass oil or oil vapors shall be installed in the air supply line between the compressor
and DRINKING WATER system when compressed air is used to pressurize the water tank system. P
5-303.12 PROTECTIVE COVER OR DEVICE
A cap and keeper chain, closed cabinet, closed storage tube, or other APPROVED protective cover or device
shall be provided for a water inlet, outlet, and hose.
5-303.13 MOBILE FOOD ESTABLISHMENT TANK INLET
A MOBILE FOOD ESTABLISHMENT'S water tank inlet shall be:
(A) 19.1 mm (three-fourths inch) in inner diameter or less; and
(B) Provided with a hose connection of a size or type that will prevent its use for any other service.
OPERATION AND MAINTENANCE
5-304.11 SYSTEM FLUSHING AND SANITIZATION
A water tank, pump, and hoses shall be flushed and SANITIZED before being place in service after construction,
repair, modification, and periods of nonuse. P
5-304.12 USING A PUMP AND HOSES, BACKFLOW PREVENTION
A PERSON shall operate a water tank, pump, and hoses so that backflow and other contamination of the water
supply are prevented.
101
5-304.13 PROTECTING INLET, OUTLET, AND HOSE FITTING
If not in use, a water tank and hose inlet and outlet fitting shall be protected using a cover or device as
specified under § 5-303.12.
5-304.14 TANK, PUMP, AND HOSES, DEDICATION
(A) Except as specified in (B) of this section, a water tank, pump, and hoses used for conveying DRINKING
WATER shall be used for no other purpose. P
(B) Water tanks, pumps, and hoses APPROVED for liquid FOODS may be used for conveying DRINKING WATER if
they are cleaned and SANITIZED before they are used to convey water.
5-4 SEWAGE, OTHER LIQUID WASTE AND RAINWATER
SUBPARTS 5-401 Mobile Holding Tank
5-402 Retention, Drainage, and Delivery
5-403 Disposal Facility
MOBILE HOLDING TANK
5-401.11 CAPACITY AND DRAINAGE
A SEWAGE holding tank in a MOBILE FOOD ESTABLISHMENT shall be:
(A) Sized 15 percent larger in capacity that the water supply tank; and
(B) Sloped to a drain that is 25 mm (1 inch) in diameter or greater, equipped with a shut-off valve.
RETENTION, DRAINAGE, AND DELIVERY
5-402.10 ESTABLISHMENT DRAINAGE SYSTEM
FOOD ESTABLISHMENT drainage systems, including grease traps, that convey SEWAGE shall be designed and
installed as specified under ¶ 5-202.11(A).
5-402.11 BACKFLOW PREVENTION
(A) Except as specified in ¶¶ (B), (C), and (D) of this section, a direct connection may not exist between
the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or
UTENSILS are placed. P
(B) Paragraph (A) of this section does not apply to floor drains that originate in refrigerated spaces that are
constructed as an integral part of the building.
(C) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a
floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine
outlet is connected to the inlet side of a properly vented floor drain trap.
(D) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
5-402.12 GREASE TRAP
If used, a grease trap shall be located to be easily accessible for cleaning.
5-402.13 CONVEYING SEWAGE
SEWAGE shall be conveyed to the point of disposal through an APPROVED sanitary SEWAGE system or other
system, including use of SEWAGE transport vehicles, waste retention tanks, pumps, pipes, hoses, and
connections that are constructed, maintained, and operated according to LAW. P
102
5-402.14 REMOVING MOBILE FOOD ESTABLISHMENT WASTES
SEWAGE and other liquid wastes shall be removed from a MOBILE FOOD ESTABLISHMENT at an APPROVED waste
SERVICING AREA or by a SEWAGE transport vehicle in such a way that a public health HAZARD or nuisance is not
created. Pf
5-402.15 FLUSHING A WASTE RETENTION TANK
A tank for liquid waste retention shall be thoroughly flushed and drained in a sanitary manner during the
servicing operation.
DISPOSAL FACILITY
5-403.11 APPROVED SEWAGE DISPOSAL SYSTEM
SEWAGE shall be disposed through an APPROVED facility that is:
(A) A public SEWAGE treatment plant; P or
(B) An individual SEWAGE disposal system that is sized, constructed, maintained, and operated according
to LAW. P
5-403.12 OTHER LIQUID WASTES AND RAINWATER
Condensate drainage and other non-SEWAGE liquids and rainwater shall be drained from a point of discharge
to disposal according to LAW.
5-5 REFUSE, RECYCLABLES AND RETURNABLES
SUBPARTS 5-501 Facilities on the Premises
5-502 Removal
5-503 Facilities for Disposal and Recycling
FACILITIES ON THE PREMISES
5-501.10 INDOOR STORAGE AREA
If located within the FOOD ESTABLISHMENT, a storage area for REFUSE, recyclables, and returnables shall meet
the requirements specified under §§ 6-101.11, 6-201.11, 6-201.18, 6-202.15, and 6-202.16.
5-501.11 OUTDOOR STORAGE SURFACE
An outdoor storage surface for REFUSE, recyclables, and returnables shall be constructed of nonabsorbent
material such as concrete or asphalt and shall be SMOOTH, durable, and sloped to drain.
5-501.12 OUTDOOR ENCLOSURE
If used, an outdoor enclosure for REFUSE, recyclables, and returnables shall be constructed of durable and
cleanable materials.
5-501.13 RECEPTACLES
(A) Except as specified in ¶ (B) of this section, receptacles and waste handling units for REFUSE,
recyclables, and returnables and for use with materials containing FOOD residue shall be durable,
cleanable, insect- and rodent-resistant, leak-proof, and nonabsorbent.
(B) Plastic bags and wet strength paper bags may be used to line receptacles for storage inside the FOOD
ESTABLISHMENT, or within closed outside receptacles.
5-501.14 RECEPTACLES IN VENDING MACHINES
Except for a receptacle for BEVERAGE bottle crown closures, a REFUSE receptacle may not be located within a
VENDING MACHINE.
103
5-501.15 OUTSIDE RECEPTACLES
(A) Receptacles and waste handling units for REFUSE, recyclables, and returnables used with materials
containing FOOD residue and used outside the FOOD ESTABLISHMENT shall be designed and constructed to
have tight-fitting lids, doors, or covers.
(B) Receptacles and waste handling units for REFUSE and recyclables such as an on-site compactor shall be
installed so that accumulation of debris and insect and rodent attraction and harborage are minimized
and effective cleaning is facilitated around and, if the unit is not installed flush with the base pad,
under the unit.
5-501.16 STORAGE AREAS, ROOMS, AND RECEPTACLES, CAPACITY AND AVAILABILITY
(A) An inside storage room and area and outside storage area and enclosure, and receptacles shall be of
sufficient capacity to hold REFUSE, recyclables, and returnables that accumulate.
(B) A receptacle shall be provided in each area of the FOOD ESTABLISHMENT or PREMISES where REFUSE is
generated or commonly discarded or where recyclables or returnables are placed.
(C) If disposable towels are used at handwashing lavatories, a waste receptacle shall be located at each
lavatory or group of adjacent lavatories.
5-501.17 TOILET ROOM RECEPTACLE, COVERED
A toilet room used by females shall be provided with a covered receptacle for sanitary napkins.
5-501.18 CLEANING IMPLEMENTS AND SUPPLIES
(A) Except as specified in ¶ (B) of this section, suitable cleaning implements and supplies such as high
pressure pumps, hot water, steam, and detergent shall be provided as necessary for effective cleaning
of receptacles and waste handling units for REFUSE, recyclables, and returnables.
(B) If APPROVED, off-PREMISES-based cleaning services may be used if on-PREMISES cleaning implements and
supplies are not provided.
5-501.19 STORAGE AREAS, REDEEMING MACHINES, RECEPTACLES AND WASTE HANDLING
UNITS, LOCATION
(A) An area designated for REFUSE, recyclables, returnables, and except as specified in ¶ (B) of this section,
a redeeming machine for recyclables or returnables shall be located so that it is separate from FOOD,
EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES and a public health HAZARD or
nuisance is not created.
(B) A redeeming machine may be located in the PACKAGED FOOD storage area or CONSUMER area of a FOOD
ESTABLISHMENT if FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES are not
subject to contamination from the machines and a public health HAZARD or nuisance is not created.
(C) The location of receptacles and waste handling units for REFUSE, recyclables, and returnables may not
create a public health HAZARD or nuisance or interfere with the cleaning of adjacent space.
5-501.110 STORING REFUSE, RECYCLABLES, AND RETURNABLES
REFUSE, recyclables, and returnables shall be stored in receptacles or waste handling units so that they are
inaccessible to insects and rodents.
5-501.111 AREAS, ENCLOSURES, AND RECEPTACLES, GOOD REPAIR
Storage areas, enclosures, and receptacles for REFUSE, recyclables, and returnables shall be maintained in
good repair.
5-501.112 OUTSIDE STORAGE PROHIBITIONS
(A) Except as specified in ¶ (B) of this section, REFUSE receptacles not meeting the requirements specified
under ¶ 5-501.13(A) such as receptacles that are not rodent-resistant, unprotected plastic bags and
paper bags, or baled units that contain materials with FOOD residue may not be stored outside.
104
(B) Cardboard or other packaging material that does not contain FOOD residues and that is awaiting
regularly scheduled delivery to a recycling or disposal site may be stored outside without being in a
covered receptacle if it is stored so that it does not create a rodent harborage problem.
5-501.113 COVERING RECEPTACLES
Receptacles and waste handling units for REFUSE, recyclables, and returnables shall be kept covered:
(A) Inside the FOOD ESTABLISHMENT if the receptacles and units:
(1) Contain FOOD residue and are not in continuous use; or
(2) After they are filled; and
(B) With tight-fitting lids or doors if kept outside the FOOD ESTABLISHMENT.
5-501.114 USING DRAIN PLUGS
Drains in receptacles and waste handling units for REFUSE, recyclables, and returnables shall have drain plugs
in place.
5-501.115 MAINTAINING REFUSE AREAS AND ENCLOSURES
A storage area and enclosure for REFUSE, recyclables, or returnables shall be maintained free of unnecessary
items, as specified under § 6-501.114, and clean.
5-501.116 CLEANING RECEPTACLES
(A) Receptacles and waste handling units for REFUSE, recyclables, and returnables shall be thoroughly
cleaned in a way that does not contaminate FOOD, EQUIPMENT, UTENSILS, LINENS, or SINGLE-SERVICE and
SINGLE-USE ARTICLES, and waste water shall be disposed of as specified under § 5-402.13.
(B) Soiled receptacles and waste handling units for REFUSE, recyclables, and returnables shall be cleaned at
a frequency necessary to prevent them from developing a buildup of soil or becoming attractants for
insects and rodents.
REMOVAL
5-502.11 FREQUENCY
REFUSE, recyclables, and returnables shall be removed from the PREMISES at a frequency that will minimize the
development of objectionable odors and other conditions that attract or harbor insects and rodents.
5-502.12 RECEPTACLES OR VEHICLES
REFUSE, recyclables, and returnables shall be removed from the PREMISES by way of:
(A) Portable receptacles that are constructed and maintained according to LAW; or
(B) A transport vehicle that is constructed, maintained, and operated according to LAW.
FACILITIES FOR DISPOSAL AND RECYCLING
5-503.11 COMMUNITY OR INDIVIDUAL FACILITY
Solid waste not disposed of through the SEWAGE system such as through grinders and pulpers shall be
recycled or disposed of in an APPROVED public or private community recycling or REFUSE facility; or solid
waste shall be disposed of in an individual REFUSE facility such as a landfill or incinerator which is sized,
constructed, maintained, and operated according to LAW.
105
CHAPTER 6 - PHYSICAL FACILITIES
6-1 MATERIALS FOR CONSTRUCTION AND REPAIR
6-2 DESIGN, CONSTRUCTION, AND INSTALLATION
6-3 NUMBERS AND CAPACITIES
6-4 LOCATION AND PLACEMENT
6-5 MAINTENANCE AND OPERATION
6-1 MATERIALS FOR CONSTRUCTION AND REPAIR
SUBPARTS 6-101 Indoor Areas
6-102 Outdoor Areas
INDOOR AREAS
6-101.11 SURFACE CHARACTERISTICS
(A) Except as specified in ¶ (B) of this section, materials for indoor floor, wall, and ceiling surfaces under
conditions of normal use shall be:
(1) SMOOTH, durable, and EASILY CLEANABLE for areas where FOOD ESTABLISHMENT operations are
conducted;
(2) Closely woven and EASILY CLEANABLE carpet for carpeted areas; and
(3) Nonabsorbent for areas subject to moisture such as FOOD preparation area, walk-in
refrigerators, WAREWASHING areas, toilet rooms, MOBILE FOOD ESTABLISHMENT SERVICING AREAS, and
areas subject to flushing or spray cleaning methods.
(B) In a TEMPORARY FOOD ESTABLISHMENT:
(1) If graded to drain, a floor may be concrete, machine-laid asphalt, or dirt or gravel if it is covered
with mats, removable platforms, duckboards, or other APPROVED materials that are effectively
treated to control dust and mud; and
(2) Walls and ceiling may be constructed of a material that protects the interior from the weather
and windblown dust and debris.
OUTDOOR AREAS
6-102.11 SURFACE CHARACTERISTICS
(A) The outdoor walking and driving areas shall be surfaced with concrete, asphalt, or gravel or other
materials that have been effectively treated to minimize dust, facilitate maintenance, and prevent
muddy conditions.
(B) Exterior surfaces of buildings and MOBILE FOOD ESTABLISHMENTS shall be of weather-resistant materials
and shall comply with LAW.
(C) Outdoor storage areas for REFUSE, recyclables, or returnables shall be of materials specified under §§
5-501.11 and 5-501.12.
106
6-2 DESIGN, CONSTRUCTION AND INSTALLATION
SUBPARTS 6-201 Cleanability
6-202 Functionality
CLEANABILITY
6-201.11 FLOORS, WALLS, AND CEILINGS
Except as specified under § 6-201.14 and except for anti-slip floor coverings or applications that may be used
for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed,
and installed so they are SMOOTH and EASILY CLEANABLE.
6-201.12 FLOORS, WALLS, AND CEILINGS, UTILITY LINES
(A) Utility service lines and pipes may not be unnecessarily exposed.
(B) Exposed utility service lines and pipes shall be installed so they do not obstruct or prevent cleaning of
the floors, walls, or ceilings.
(C) Exposed horizontal utility service lines and pipes may not be installed on the floor.
6-201.13 FLOOR AND WALL JUNCTURES, COVED, AND ENCLOSED OR SEALED
(A) In FOOD ESTABLISHMENTS in which cleaning methods other than water flushing are used for cleaning
floors, the floor and wall junctures shall be coved and closed to no larger than 1 mm (one thirty-
second inch).
(B) The floors in FOOD ESTABLISHMENTS in which water flush cleaning methods are used shall be provided
with drains and be graded to drain, and the floor and wall junctures shall be coved and SEALED.
6-201.14 FLOOR CARPETING, RESTRICTIONS AND INSTALLATION
(A) A floor covering such as carpeting or similar material may not be installed as a floor covering in FOOD
preparation areas, walk-in refrigerators, WAREWASHING areas, toilet room areas where handwashing
lavatories, toilets, and urinals are located, REFUSE storage rooms, or other areas where the floor is
subject to moisture, flushing, or spray cleaning methods.
(B) If carpeting is installed as a floor covering in areas other than those specified under ¶ (A) of this
section, it shall be:
(1) Securely attached to the floor with a durable mastic, by using a stretch and tack method, or by
another method; and
(2) Installed tightly against the wall under the coving or installed away from the wall with a space
between the carpet and the wall and with the edges of the carpet secured by metal stripping or
some other means.
6-201.15 FLOOR COVERING, MATS AND DUCKBOARDS
Mats and duckboards shall be designed to be removable and EASILY CLEANABLE.
6-201.16 WALL AND CEILING COVERINGS AND COATINGS
(A) Wall and ceiling covering materials shall be attached so that they are EASILY CLEANABLE.
(B) Except in areas used only for dry storage, concrete, porous blocks, or bricks used for indoor wall
construction shall be finished and SEALED to provide a SMOOTH, nonabsorbent, EASILY CLEANABLE surface.
6-201.17 WALLS AND CEILINGS, ATTACHMENTS
(A) Except as specified in ¶ (B) of this section, attachments to walls and ceilings such as light fixtures,
mechanical room ventilation system components, vent covers, wall mounted fans, decorative items,
and other attachments shall be EASILY CLEANABLE.
(B) In a CONSUMER area, wall and ceiling surfaces and decorative items and attachments that are provided for
ambiance need not meet this requirement if they are kept clean.
107
6-201.18 WALLS AND CEILINGS, STUDS, JOISTS, AND RAFTERS
Except for TEMPORARY FOOD ESTABLISHMENTS, studs, joists, and rafters may not be exposed in areas subject to
moisture.
FUNCTIONALITY
6-202.11 LIGHT BULBS, PROTECTIVE SHIELDING
(A) Except as specified in ¶ (B) of this section, light bulbs shall be shielded, coated, or otherwise shatter-
resistant in areas where there is exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped
SINGLE-SERVICE and SINGLE-USE ARTICLES.
(B) Shielded, coated, or otherwise shatter-resistant bulbs need not be used in areas used only for storing FOOD
in unopened packages, if:
(1) The integrity of the packages cannot be affected by broken glass falling onto them; and
(2) The packages are capable of being cleaned of debris from broken bulbs before the packages are
opened.
(C) An infrared or other heat lamp shall be protected against breakage by a shield surrounding and
extending beyond the bulb so that only the face of the bulb is exposed.
6-202.12 HEATING, VENTILATION, AIR CONDITIONING SYSTEM VENTS
Heating, ventilating, and air conditioning systems shall be designed and installed so that make-up air intake
and exhaust vents do not cause contamination of FOOD, FOOD-CONTACT SURFACES, EQUIPMENT, or UTENSILS.
6-202.13 INSECT CONTROL DEVICES, DESIGN AND INSTALLATION
(A) Insect control devices that are used to electrocute or stun flying insects shall be designed to retain the
insect within the device.
(B) Insect control devices shall be installed so that:
(1) The devices are not located over a FOOD preparation area; and
(2) Dead insects and insect fragments are prevented from being impelled onto or falling on
exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-
USE ARTICLES.
6-202.14 TOILET ROOMS, ENCLOSED
Except where a toilet room is located outside a FOOD ESTABLISHMENT and does not open directly into the FOOD
ESTABLISHMENT such as a toilet room that is provided by the management of a shopping mall, a toilet room
located on the PREMISES shall be completely enclosed and provided with tightfitting and self-closing door.
6-202.15 OUTER OPENINGS, PROTECTED
(A) Except as specified in ¶¶ (B), (C), and (E) and under ¶ (D) of this section, outer openings of a FOOD
ESTABLISHMENT shall be protected against the entry of insects and rodents by;
(1) Filling or closing holes and other gaps along floors, walls, and ceilings;
(2) Closed, tight-fitting windows; and
(3) Solid, self-closing, tight-fitting doors.
(B) Paragraph (A) of this section does not apply if a FOOD ESTABLISHMENT opens into a larger structure, such as
a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings
from the larger or attached structure are protected against the entry of insects and rodents.
(C) Exterior doors used as exits need not be self-closing if they are:
(1) Solid and tight-fitting:
(2) Designated for use only when an emergency exists, by the fire protection authority that has
jurisdiction over the FOOD ESTABLISHMENT; and
108
(3) Limited-use so they are not used for entrance or exit from the building for purposes other than the
designated emergency exit use.
(D) Except as specified in ¶¶ (B) and (E) of this section, if the windows or doors of a FOOD ESTABLISHMENT,
or of a larger structure within which a FOOD ESTABLISHMENT is located, are kept open for ventilation or
other purposes or a TEMPORARY FOOD ESTABLISHMENT is not provided with windows and doors as
specified under ¶ (A) of this section, the openings shall be protected against the entry of insects and
rodents by:
(1) 16 mesh to 25.4 mm (16 mesh to 1 inch) screens;
(2) Properly designed and installed air curtains to control flying insects: or
(3) Other effective means.
(E) Paragraph (D) of this section does not apply if flying insects and other pests are absent due to the
location of the ESTABLISHMENT, the weather, or other limiting condition.
6-202.16 EXTERIOR WALLS AND ROOFS, PROTECTIVE BARRIER
Perimeter walls and roofs of a FOOD ESTABLISHMENT shall effectively protect the ESTABLISHMENT from the
weather and the entry of insects, rodents, and other animals.
6-202.17 OUTDOOR FOOD VENDING AREAS, OVERHEAD PROTECTION
Except for machines that vend canned BEVERAGES, if located outside, a machine used to vend FOOD shall be
provided with overhead protection.
6-202.18 OUTDOOR SERVICING AREAS, OVERHEAD PROTECTION
Except for areas used only for the loading of water or the discharge of SEWAGE and other liquid waste, through
the use of a closed system of hoses, SERVICING AREAS shall be provided with overhead protection.
6-202.19 OUTDOOR WALKING AND DRIVING SURFACES, GRADED TO DRAIN
Exterior walking and driving surfaces shall be graded to drain.
6-202.110 OUTDOOR REFUSE AREAS, CURBED AND GRADED TO DRAIN
Outdoor REFUSE areas shall be constructed in accordance with LAW and shall be curbed and graded to drain to
collect and dispose of liquid waste that results from the REFUSE and from cleaning the area and waste
receptacles.
6-202.111 PRIVATE HOMES AND LIVING OR SLEEPING QUARTERS, USE PROHIBITION
IDAPA 16.02.19.620 - PRIVATE HOMES AND LIVING OR SLEEPING QUARTERS, USE
PROHIBITION.
Modifications to Section 6-202.111. Except for COTTAGE FOOD OPERATIONS, a private home, a room used as
living or sleeping quarters, or an area directly opening into a room used as a living or sleeping quarters may
not be used for conducting FOOD ESTABLISHMENT operations. P Residential care or assisted living facilities
designed to be a homelike environment, are exempted from Section 6-202.111.
6-202.112 LIVING OR SLEEPING QUARTERS, SEPARATION
Living or sleeping quarters located on the PREMISES of a FOOD ESTABLISHMENT such as those provided for
lodging registration clerks or resident managers shall be separated from rooms and areas used for FOOD
ESTABLISHMENT operations by complete partitioning and solid self-closing doors.
109
6-3 NUMBERS AND CAPACITIES
SUBPARTS 6-301 Handwashing Sinks
6-302 Toilets and Urinals
6-303 Lighting
6-304 Ventilation
6-305 Dressing Areas and Lockers
6-306 Service Sinks
HANDWASHING SINKS
6-301.10 MINIMUM NUMBER
HANDWASHING SINKS shall be provided as specified under § 5-203.11.
6-301.11 HANDWASHING CLEANSER, AVAILABILITY
Each HANDWASHING SINK or group of 2 adjacent HANDWASHING SINKS shall be provided with a supply of hand
cleaning liquid, powder, or bar soap. Pf
6-301.12 HAND DRYING PROVISION
Each HANDWASHING SINK or group of adjacent HANDWASHING SINKS shall be provided with:
(A) Individual, disposable towels; Pf
(B) A continuous towel system that supplies the user with a clean towel; Pf or
(C) A heated-air hand drying device; Pf or
(D) A hand drying device that employs an air-knife system that delivers high velocity, pressurized air at
ambient temperatures. Pf
6-301.13 HANDWASHING AIDS AND DEVICES, USE RESTRICTIONS
A sink used for FOOD PREPARATION or UTENSIL washing, or a service sink or curbed cleaning facility used for the
disposal of mop water or similar wastes, may not be provided with the handwashing aids and devices
required for a HANDWASHING SINK as specified under § 6-301.11 & § 6-301.12 & ¶ 5-501.16(C).
6-301.14 HANDWASHING SIGNAGE
A sign or poster that notifies FOOD EMPLOYEES to wash their hands shall be provided at all HANDWASHING SINKS
used by FOOD EMPLOYEES and shall be clearly visible to FOOD EMPLOYEES.
6-301.20 DISPOSABLE TOWELS, WASTE RECEPTACLE
A HANDWASHING SINK or group of adjacent HANDWASHING SINKS that is provided with disposable towels shall be
provided with a waste receptacle as specified under ¶ 5-501.16(C).
TOILETS AND URINALS
6-302.10 MINIMUM NUMBER
Toilets and urinals shall be provided as specified under § 5-203.12.
6-302.11 TOILET TISSUE, AVAILABILITY
A supply of toilet tissue shall be available at each toilet. Pf
LIGHTING
6-303.11 INTENSITY
The light intensity shall be:
110
(A) At least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in walk-in
refrigeration units and dry FOOD storage areas and in other areas and rooms during periods of
cleaning.
(B) At least 215 lux (20 foot candles):
(1) At a surface where FOOD is provided for CONSUMER self-service such as buffets and salad bars or
where fresh produce or PACKAGED FOODS are sold or offered for consumption.,
(2) Inside EQUIPMENT such as reach-in and under-counter refrigerators; and
(3) At a distance of 75 cm (30 inches) above the floor in areas used for handwashing, WAREWASHING,
and EQUIPMENT and UTENSIL storage, and in toilet rooms; and
(C) At least 540 lux (50 foot candles) at a surface where a FOOD EMPLOYEE is working with FOOD or working
with UTENSILS or EQUIPMENT such as knives, slicers, grinders, or saws where EMPLOYEE safety is a factor.
VENTILATION
6-304.11 MECHANICAL
If necessary to keep rooms free of excessive heat, steam, condensation, vapors, obnoxious odors, smoke, and
fumes, mechanical ventilation of sufficient capacity shall be provided.
DRESSING AREAS AND LOCKERS
6-305.11 DESIGNATION
(A) Dressing rooms or dressing areas shall be designated if EMPLOYEES routinely change their clothes in
the establishment.
(B) Lockers or other suitable facilities shall be provided for the orderly storage of EMPLOYEES' clothing and
other possessions.
SERVICE SINKS
6-306.10 AVAILABILITY
A service sink or curbed cleaning facility shall be provided as specified under ¶ 5-203.13(A).
6-4 LOCATION AND PLACEMENT
SUBPARTS 6-401 Handwashing Sinks
6-402 Toilet Rooms
6-403 Employee Accommodations
6-404 Distressed Merchandise
6-405 Refuse, Recyclables, and Returnables
HANDWASHING SINKS
6-401.10 CONVENIENTLY LOCATED
HANDWASHING SINKS shall be conveniently located as specified under § 5-204.11.
TOILET ROOMS
6-402.11 CONVENIENCE AND ACCESSIBILITY
Toilet rooms shall be conveniently located and accessible to EMPLOYEES during all hours of operation.
111
EMPLOYEE ACCOMMODATIONS
6-403.11 DESIGNATED AREAS
(A) Areas designated for EMPLOYEES to eat, drink, and use tobacco shall be located so that FOOD, EQUIPMENT,
LINENS, and SINGLE-SERVICE AND SINGLE-USE ARTICLES are protected from contamination.
(B) Lockers or other suitable facilities shall be located in a designated room or area where contamination
of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES cannot occur.
DISTRESSED MERCHANDISE
6-404.11 SEGREGATION AND LOCATION
Products that are held by the PERMIT HOLDER for credit, redemption, or return to the distributor, such as
damaged, spoiled, or recalled products, shall be segregated and held in designated areas that are separated
from FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES. Pf
REFUSE, RECYCLABLES, AND RETURNABLES
6-405.10 RECEPTACLES, WASTE HANDLING UNITS, AND DESIGNATED STORAGE AREAS
Units, receptacles, and areas designated for storage of REFUSE and recyclable and returnable containers shall
be located as specified under § 5-501.19.
6-5 MAINTENANCE AND OPERATION
SUBPART 6-501 Premises, Structures, Attachments, and Fixtures - Method
PREMISES, STRUCTURES, ATTACHMENTS, AND FIXTURES – METHODS
6-501.11 REPAIRING
PHYSICAL FACILITIES shall be maintained in good repair.
6-501.12 CLEANING, FREQUENCY, AND RESTRICTIONS
(A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean.
(B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during
periods when the least amount of FOOD is exposed such as after closing.
6-501.13 CLEANING FLOORS, DUSTLESS METHODS
(A) Except as specified in ¶ (B) of this section, only dustless methods of cleaning shall be used, such as
wet cleaning, vacuum cleaning, mopping with treated dust mops, or sweeping using a broom and
dust-arresting compounds.
(B) Spills or drippage on floors that occur between normal floor cleaning times may be cleaned:
(1) Without the use of dust-arresting compounds; and
(2) In the case of liquid spills or drippage, with the use of a small amount of absorbent compound
such as sawdust or diatomaceous earth applied immediately before spot cleaning.
6-501.14 CLEANING VENTILATION SYSTEMS, NUISANCE AND DISCHARGE P0ROHIBITION
(A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of
contamination by dust, dirt, and other materials.
(B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or
unLAWful discharge.
112
6-501.15 CLEANING MAINTENANCE TOOLS, PREVENTING CONTAMINATION
FOOD preparation sinks, HANDWASHING SINKS, and WAREWASHING EQUIPMENT may not be used for the cleaning of
maintenance tools, the preparation or holding of maintenance materials, or the disposal of mop water and
similar liquid wastes.
6-501.16 DRYING MOPS
After use, mops shall be place in a position that allows them to air-dry without soiling walls, EQUIPMENT, or
supplies.
6-501.17 ABSORBENT MATERIALS ON FLOORS, USE LIMITATION
Except as specified in ¶ 6-501.13(B), sawdust, wood shavings, granular salt, baked clay, diatomaceous earth,
or similar materials may not be used on floors.
6-501.18 CLEANING OF PLUMBING FIXTURES
PLUMBING FIXTURES such as HANDWASHING SINKS, toilets, and urinals shall be cleaned as often as necessary to
keep them clean.
6-501.19 CLOSING TOILET ROOM DOORS
Except during cleaning and maintenance operations, toilet room doors as specified under § 6-202.14 shall be
kept closed.
6-501.110 USING DRESSING ROOMS AND LOCKERS
(A) Dressing rooms shall be used by EMPLOYEES if the EMPLOYEES regularly change their clothes in the
ESTABLISHMENT.
(B) Lockers or other suitable facilities shall be used for the orderly storage of EMPLOYEE clothing and other
possessions.
6-501.111 CONTROLLING PESTS
The premises shall be maintained free of insects, rodents, and other pests. The presence of insects, rodents,
and other pests shall be controlled to eliminate their presence on the PREMISES by:
(A) Routinely inspecting incoming shipments of FOOD and supplies;
(B) Routinely inspecting the PREMISES for evidence of pests;
(C) Using methods, if pests are found, such as trapping devices or other means of pest control as specified
under §§ 7-202.12, 7-206.12, and 7-206.13; Pf and
(D) Eliminating harborage conditions.
6-501.112 REMOVING DEAD OR TRAPPED BIRDS, INSECTS, RODENTS, AND OTHER PESTS
Dead or trapped birds, insects, rodents, and other pests shall be removed from control devices and the
PREMISES at a frequency that prevents their accumulation, decomposition, or the attraction of pests.
6-501.113 STORING MAINTENANCE TOOLS
Maintenance tools such as brooms, mops, vacuum cleaners, and similar items shall be:
(A) Stored so they do not contaminate FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE
ARTICLES; and
(B) Stored in an orderly manner that facilitates cleaning the area used for storing the maintenance tools.
6-501.114 MAINTAINING PREMISES, UNNECESSARY ITEMS AND LITTER
The PREMISES shall be free of:
(A) Items that are unnecessary to the operation or maintenance of the ESTABLISHMENT such as EQUIPMENT
that is nonfunctional or no longer used; and
(B) Litter.
113
6-501.115 PROHIBITING ANIMALS
(A) Except as specified in ¶¶ (B) and (C) of this section, live animals may not be allowed on the PREMISES of
a FOOD ESTABLISHMENT. Pf
(B) Live animals may be allowed in the following situations if the contamination of FOOD; clean EQUIPMENT,
UTENSILS, and LINENS; and unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES cannot result:
(1) Edible FISH or decorative FISH in aquariums, shellfish or crustacea on ice or under refrigeration,
and shellfish and crustacea in display tank systems;
(2) Patrol dogs accompanying police or security officers in offices and dining, sales, and storage
areas, and sentry dogs running loose in outside fenced areas:
(3) In areas that are not used for FOOD preparation and that are usually open for customers such as
dining and sales areas, SERVICE ANIMALS that are controlled by the disabled EMPLOYEE or PERSON, if a
health or safety HAZARD will not result from the presence or activities of the SERVICE ANIMAL;
(4) Pets in the common dining areas of institutional care facilities such as nursing homes, assisted
living facilities, group homes, or residential care facilities at times other than during meals if:
(a) Effective partitioning and self-closing doors separate the common dining areas from FOOD
storage or FOOD preparation areas,
(b) Condiments, EQUIPMENT, and UTENSILS are stored in enclosed cabinets or removed from the
common dining areas when pets are present, and
(c) Dining areas including tables, countertops, and similar surfaces are effectively cleaned
before the next meal service; and
(5) In areas that are not used for FOOD preparation, storage, sales, display, or dining, in which there
are caged animals or animals that are similarly confined, such as in a variety store that sells pets
or a tourist park that displays animals.
(C) Live or dead FISH bait may be stored if contamination of FOOD; clean EQUIPMENT, UTENSILS, and LINENS; and
unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES cannot result.
114
CHAPTER 7 - POISONOUS OR TOXIC MATERIALS
7-1 LABELING AND IDENTIFICATION
7-2 OPERATIONAL SUPPLIES AND APPLICATIONS
7-3 STOCK AND RETAIL SALE
7-1 LABELING AND IDENTIFICATION
SUBPARTS 7-101 Original Containers
7-102 Working Containers
ORIGINAL CONTAINERS
7-101.11 IDENTIFYING INFORMATION, PROMINENCE
Containers of POISONOUS OR TOXIC MATERIALS and PERSONAL CARE ITEMS shall bear a legible manufacturer's label. Pf
WORKING CONTAINERS
7-102.11 COMMON NAME
Working containers used for storing POISONOUS OR TOXIC MATERIALS such as cleaners and SANITIZERS taken from
bulk supplies shall be clearly and individually identified with the common name of the material. Pf
7-2 OPERATIONAL SUPPLIES AND APPLICATIONS
SUBPARTS 7-201 Storage
7-202 Presence and Use
7-203 Container Prohibitions
7-204 Chemicals
7-205 Lubricants
7-206 Pesticides
7-207 Medicines
7-208 First Aid Supplies
7-209 Other Personal Care Items
STORAGE
7-201.11 SEPARATION
POISONOUS OR TOXIC MATERIALS shall be stored so they cannot contaminate FOOD, EQUIPMENT, UTENSILS, LINENS,
and SINGLE-SERVICE and SINGLE-USE ARTICLES by:
(A) Separating the POISONOUS OR TOXIC MATERIALS by spacing or partitioning; P and
(B) Locating the POISONOUS OR TOXIC MATERIALS in an area that is not above FOOD, EQUIPMENT, UTENSILS, LINENS,
and SINGLE-SERVICE or SINGLE-USE ARTICLES. This paragraph does not apply to EQUIPMENT and UTENSIL
cleaners and SANITIZERS that are stored in WAREWASHING areas for availability and convenience if the
materials are stored to prevent contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE
and SINGLE-USE ARTICLES. P
115
PRESENCE AND USE
7-202.11 RESTRICTION
(A) Only those POISONOUS OR TOXIC MATERIALS that are required for the operation and maintenance of a FOOD
ESTABLISHMENT, such as for the cleaning and SANITIZING of EQUIPMENT and UTENSILS and the control of
insects and rodents, shall be allowed in a FOOD ESTABLISHMENT. Pf
(B) Paragraph (A) of this section does not apply to PACKAGED POISONOUS OR TOXIC MATERIALS that are for retail
sale.
7-202.12 CONDITIONS OF USE
POISONOUS OR TOXIC MATERIALS shall be:
(A) Used according to:
(1) LAW and this Code,
(2) Manufacturer’s use directions included in labeling, and, for a pesticide, manufacturer's label
instructions that state that use is allowed in a FOOD ESTABLISHMENT, P
(3) The conditions of certification, if certification is required, for use of the pest control materials, P
and
(4) Additional conditions that may be established by the REGULATORY AUTHORITY; and
(B) Applied so that:
(1) A HAZARD to EMPLOYEES or other PERSONS is not constituted, P and
(2) Contamination including toxic residues due to drip, drain, fog, splash or spray on FOOD,
EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES is prevented, and for a
RESTRICTED USE PESTICIDE, this is achieved by: P
(a) Removing the items, P
(b) Covering the items with impermeable covers, P or
(c) Taking other appropriate preventive actions, P and
(d) Cleaning and SANITIZING EQUIPMENT and UTENSILS after application. P
(C) A RESTRICTED USE PESTICIDE shall be applied only by an applicator certified as defined in 7 USC 136
definition, (e) Certified Applicator, of the Federal Insecticide, Fungicide, and Rodenticide Act, or a
PERSON under the direct supervision of a certified applicator. Pf
CONTAINER PROHIBITIONS
7-203.11 POISONOUS OR TOXIC MATERIAL CONTAINERS
A container previously used to store POISONOUS OR TOXIC MATERIALS may not be used to store, transport, or
dispense FOOD. P
CHEMICALS
7-204.11 SANITIZERS, CRITERIA
Chemical SANITIZERS, including chemical SANITIZING solutions generated on-site, and other chemical
antimicrobials applied to FOOD-CONTACT SURFACES shall:
(A) Meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert
ingredients for use in antimicrobial formations (FOOD-CONTACT SURFACE SANITIZING SOLUTIONS) P, OR
(B) Meet the requirements as specified in 40 CFR 180.2020 Pesticide Chemical Not Requiring a Tolerance
or Exemption from Tolerance-Non-FOOD determinations. P
116
7-204.12 CHEMICALS FOR WASHING, TREATMENT, STORAGE AND PROCESSING FRUITS AND
VEGETABLES, CRITERIA
(A) Chemicals, including those generated on-site, used to wash or peel raw, whole fruits and vegetables
shall:
(1) Be an APPROVED FOOD ADDITIVE listed for this intended use in 21 CFR 173, P or
(2) Be generally recognized as safe (GRAS) for this intended use, P or
(3) Be the subject of an effective FOOD contact notification for this intended use (only effective for
the manufacturer or supplier identified in the notification), P and
(4) Meet the requirements in 40 CFR 156 Labeling Requirements for Pesticide Devices. P
(B) Ozone as an antimicrobial agent used in the treatment, storage, and processing of fruits and
vegetables in a FOOD ESTABLISHMENT shall meet the requirements specified in 21 CFR 173.368 Ozone. P
7-204.13 BOILER WATER ADDITIVES, CRITERIA
Chemicals used as boiler water ADDITIVES shall meet the requirements specified in 21 CFR 173.310 Boiler
water ADDITIVES. P
7-204.14 DRYING AGENTS, CRITERIA
Drying agents used in conjunction with SANITIZATION shall:
(A) Contain only components that are listed as one of the following:
(1) Generally recognized as safe for use in FOOD as specified in 21 CFR 182 - Substances Generally
Recognized as Safe, or 21 CFR 184 - Direct FOOD Substances Affirmed as Generally Recognized
as Safe, P
(2) General recognized as safe for intended use as specified in 21 CFR 186 - Indirect FOOD
Substances Affirmed as Generally Recognized as Safe, P
(3) Generally recognized as safe for the intended use as determined by experts qualified in
scientific training and experience to evaluate the safety of substances added, directly or
indirectly, to FOOD as described in 21 CFR 170.30 Eligibility for classification as generally
recognized as safe (GRAS), P
(4) Subject of an effective FOOD Contact Notification as described in the Federal FOOD, Drug and
Cosmetic Act (FFDCA) Section 409(h), P
(5) APPROVED for use as a drying agent under a prior sanction as described in the Federal FOOD,
Drug and Cosmetic Act (FFDCA) § 201(s)(4); P
(6) Specifically regulated as an indirect FOOD ADDITIVE for use as drying agent as specified in 21 CFR
Parts 174-178, P or
(7) APPROVED for use as a drying agent under the threshold of regulation process established by 21
CFR 170.39 Threshold of regulation for substances used in FOOD-contact articles, P and
(B) When SANITIZATION is with chemicals, the APPROVAL required under Subparagraph (A)(5) or (A)(7) of
this section or the regulation as an indirect FOOD ADDITIVE required under Subparagraph (A)(6) of this
section, shall be specifically for use with chemical SANITIZING solutions. P
LUBRICANTS
7-205.11 INCIDENTAL FOOD CONTACT, CRITERIA
Lubricants shall meet the requirements specified in 21 CFR 178.3570 Lubricants with Incidental FOOD
contact, if they are used on FOOD-CONTACT SURFACES, on bearings and gears located on or within FOOD-CONTACT
SURFACES, or on bearings and gears that are located so that lubricants may leak, drip, or be forced into FOOD or
onto FOOD-CONTACT SURFACES. P
117
PESTICIDES
7-206.11 RESTRICTED USE PESTICIDES, CRITERIA
RESTRICTED USE PESTICIDES specified under ¶ 7-202.12(C) shall meet the requirements specified in 40 CFR 152
Subpart I – Classification of Pesticides. P
7-206.12 RODENT BAIT STATIONS
Rodent bait shall be contained in a covered, tamper-resistant bait station. P
7-206.13 TRACKING POWDERS, PEST CONTROL AND MONITORING
(A) Except as specified in ¶ (B) of this section, a tracking powder pesticide may not be used in a FOOD
ESTABLISHMENT. P
(B) Is used, a nontoxic tracking powder such as talcum or flour may not contaminate FOOD, EQUIPMENT,
UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES. P
7-207.11 RESTRICTION AND STORAGE
IDAPA 16.02.19.720 MODIFICATIONS TO SECTION 7-207.11. RESTRICTION AND STORAGE
OF MEDICINES
01. Medicines Allowed in a FOOD ESTABLISHMENT. Only those medicines that are necessary for the
health of EMPLOYEES, patients or residents in a care facility shall be allowed in a FOOD ESTABLISHMENT. Pf
This section does not apply to medicines that are stored or displayed for retail sale.
02. Labeling of Medicines. Medicines that are in a FOOD ESTABLISHMENT for the EMPLOYEES, patients or
residents use must be labeled as specified under § 7-101.11 and located to prevent the
contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES. P
7-207.12 REFRIGERATED MEDICINES, STORAGE
IDAPA 16.02.19.721 MODIFICATION TO SECTION 7-207.12. MEDICINES BELONGING TO
EMPLOYEES, PATIENTS OR RESIDENTS IN A CARE FACILITY THAT REQUIRE REFRIGERATION
MAY BE STORED IN A FOOD REFRIGERATOR USING THE FOLLOWING CRITERIA:
01. Medicines Stored in a Leak-proof Container. Medicines must be stored in a PACKAGE and kept
inside a covered, leak proof container that is identified as a container for the storage of medicines. P
02. Accessibility of Stored Medicines. Medicines will be stored to permit access to self-medicating
patients or residents to their individual medication. Authorized staff in a care facility have access to
these medications. P
FIRST AID SUPPLIES
7-208.11 STORAGE
First aid supplies that are in a FOOD ESTABLISHMENT for the EMPLOYEES' use shall be:
(A) Labeled as specified under § 7-101.11; Pf and
(B) Stored in a kit or a container that is located to prevent the contamination of FOOD EQUIPMENT, UTENSILS,
and LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES. P
OTHER PERSONAL CARE ITEMS
7-209.11 STORAGE
Except as specified under §§ 7-207.12 and 7-208.11, EMPLOYEES shall store their PERSONAL CARE ITEMS in
facilities as specified under ¶ 6-305.11(B).
118
7-3 STOCK AND RETAIL SALE
SUBPART 7-301 Storage and Display
STORAGE AND DISPLAY
7-301.11 SEPARATION
POISONOUS OR TOXIC MATERIALS shall be stored and displayed for retail sale so they cannot contaminate FOOD,
EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES by:
(A) Separating the POISONOUS OR TOXIC MATERIALS by spacing or partitioning; P and
(B) Locating the POISONOUS OR TOXIC MATERIALS in an area that is not above FOOD, EQUIPMENT, UTENSILS, LINEN,
and SINGLE-SERVICE or SINGLE-USE ARTICLES. P
119
CHAPTER 8 - COMPLIANCE AND ENFORCEMENT
8-1 CODE APPLICABILITY
8-2 PLAN SUBMISSION AND APPROVAL
8-3 PERMIT TO OPERATE
8-4 INSPECTION AND CORRECTION OF VIOLATIONS
8-5 PREVENTION OF FOODBORNE DISEASE TRANSMISSION BY EMPLOYEES
8-1 CODE APPLICABILITY
SUBPARTS 8-101 Use for Intended Purpose
8-102 Additional Requirements
8-103 Variances
USE FOR INTENDED PURPOSE
8-101.10 PUBLIC HEALTH PROTECTION
(A) The REGULATORY AUTHORITY shall apply this Code to promote its underlying purpose, as specified in § 1-
102.10, of safeguarding public health and ensuring that FOOD is safe, unADULTERATED, and honestly
presented when offered to the CONSUMER.
(B) In enforcing the provisions of this Code, the REGULATORY AUTHORITY shall assess existing facilities or
EQUIPMENT that were in use before the effective date of this Code based on the following
considerations:
(1) Whether the facilities of EQUIPMENT are in good repair and capable of being maintained in a
sanitary condition;
(2) Whether FOOD-CONTACT SURFACES comply with Subpart 4-101;
(3) Whether the capacities of cooling, heating, and holding EQUIPMENT are sufficient to comply with
§ 4-301.11; and
(4) The existence of a documented agreement with the PERMIT HOLDER that the facilities or
EQUIPMENT will be replaced as specified under ¶ 8-304.11(G).
ADDITIONAL REQUIREMENTS
8-102.10 PREVENTING HEALTH HAZARDS, PROVISION FOR CONDITIONS NOT ADDRESSED
(A) If necessary to protect against public health HAZARDS or nuisances, the REGULATORY AUTHORITY may
impose specific requirements in addition to the requirements contained in this Code that are
authorized by LAW.
(B) The REGULATORY AUTHORITY shall document the conditions that necessitate the imposition of additional
requirements and the underlying public health rationale. The documentation shall be provided to the
PERMIT applicant or PERMIT HOLDER and a copy shall be maintained in the REGULATORY AUTHORITY'S file for
the FOOD ESTABLISHMENT.
VARIANCES
8-103.10 MODIFICATIONS AND WAIVERS
The REGULATORY AUTHORITY may grant a VARIANCE by modifying or waiving the requirements of this Code if in
the opinion of the REGULATORY AUTHORITY a health HAZARD or nuisance will not result from the VARIANCE. If a
VARIANCE is granted, the REGULATORY AUTHORITY shall retain the information specified under § 8-103.11 in its
records for the FOOD ESTABLISHMENT.
120
8-103.11 DOCUMENTATION OF PROPOSED VARIANCE AND JUSTIFICATION
Before a VARIANCE from a requirement of this Code is APPROVED, the information that shall be provided by the
PERSON requesting the VARIANCE and retained in the REGULATORY AUTHORITY's file on the FOOD ESTABLISHMENT
includes:
(A) A statement of the proposed VARIANCE of the Code requirement citing relevant Code section numbers;
Pf
(B) An analysis of the rationale for how the potential public health HAZARDS and nuisances addressed by
the relevant Code sections will be alternately addressed by the proposal; Pf and
(C) A HACCP PLAN if required as specified under ¶ 8-201.13(A) that includes the information specified
under § 8-201.14 as it is relevant to the VARIANCE requested. Pf
8-103.12 CONFORMANCE WITH APPROVED PROCEDURES
If the REGULATORY AUTHORITY grants a VARIANCE as specified in § 8-103.10, or a HACCP PLAN is otherwise
required as specified under § 8-201.13, the PERMIT HOLDER shall:
(A) Comply with the HACCP PLANS and procedures that are submitted as specified under § 8-201.14 and
APPROVED as a basis for the modification or waiver; P and
(B) Maintain and provide to the REGULATORY AUTHORITY, upon request, records specified under ¶¶ 8-
201.14(D) and (E) that demonstrate that the following are routinely employed;
(1) Procedures for monitoring the CRITICAL CONTROL POINTS, Pf
(2) Monitoring of the CRITICAL CONTROL POINTS, Pf
(3) Verification of the effectiveness of the operation or process, Pf and
(4) Necessary corrective actions if there is failure at a CRITICAL CONTROL POINT. Pf
8-2 PLAN SUBMISSION AND APPROVAL
SUBPARTS 8-201 Faculty and Operating Plans
8-202 Confidentiality
8-203 Construction Inspection and Approval
FACILITY AND OPERATING PLANS
8-201.11 WHEN PLANS ARE REQUIRED
A PERMIT applicant or PERMIT HOLDER shall submit to the REGULATORY AUTHORITY properly prepared plans and
specifications for review and APPROVAL before:
(A) The construction of a FOOD ESTABLISHMENT; Pf
(B) The conversion of an existing structure for use as a FOOD ESTABLISHMENT; Pf or
(C) The remodeling of a FOOD ESTABLISHMENT or a change of type of FOOD ESTABLISHMENT or FOOD operation
as specified under ¶ 8-302.14(C) if the REGULATORY AUTHORITY determines that plans and specifications
are necessary to ensure compliance with this Code. Pf
8-201.12 CONTENTS OF THE PLANS AND SPECIFICATIONS
The plans and specifications for a FOOD ESTABLISHMENT, including a FOOD ESTABLISHMENT specified under § 8-
201.13, shall include, as required by the REGULATORY AUTHORITY based on the type of operation, type of FOOD
preparation, and FOODS prepared, the following information to demonstrate conformance with Code
provisions:
(A) Intended menu;
(B) Anticipated volume of FOOD to be stored, prepared, and sold or served;
(C) Proposed layout, mechanical schematics, construction materials, and finish schedules;
121
(D) Proposed EQUIPMENT types, manufacturers, model numbers, locations, dimensions, performance
capacities, and installation specifications;
(E) Evidence that standard procedures that ensure compliance with the requirements of this Code are
developed or are being developed; and
(F) Other information that may be required by the REGULATORY AUTHORITY for the proper review of the
proposed construction, conversion or modification, and procedures for operating a FOOD
ESTABLISHMENT.
8-201.13 WHEN A HACCP PLAN IS REQUIRED
(A) Before engaging in an activity that requires a HACCP PLAN, a PERMIT applicant or PERMIT HOLDER shall
submit to the REGULATORY AUTHORITY for APPROVAL a properly prepared HACCP PLAN as specified under
§ 8-201.14 and the relevant provisions of this Code if:
(1) Submission of a HACCP PLAN is required according to LAW;
(2) A VARIANCE is required as specified under Subparagraph 3-401.11(D)(4), 3-502.11, or 4-
204.110(B);
(3) The REGULATORY AUTHORITY determines that a FOOD preparation or processing method requires a
VARIANCE based on a plan submittal specified under § 8-201.12 an inspectional finding, or a
VARIANCE request.
(B) Before engaging in REDUCED OXYGEN PACKAGING without a VARIANCE as specified under § 3-502.12, a
PERMIT applicant or PERMIT HOLDER shall submit a properly prepared HACCP PLAN to the REGULATORY
AUTHORITY.
8-201.14 CONTENTS OF A HACCP PLAN
For a FOOD ESTABLISHMENT that is required under § 8-201.13 to have a HACCP PLAN, the plan and specifications
shall indicate:
(A) A categorization of the types of TIME/TEMPERATURE CONTROL FOR SAFETY FOODS that are specified in the
menu such as soups and sauces, salads, and bulk, solid FOODS such as MEAT roasts, or other FOODS that
are specified by the REGULATORY AUTHORITY; Pf
(B) A flow diagram by specific FOOD or category type identifying CRITICAL CONTROL POINTS and providing
information on the following:
(1) Ingredients, materials, and EQUIPMENT used in the preparation of that FOOD, Pf and
(2) Formulations or recipes that delineate methods and procedural control measures that address
the FOOD safety concerns involved; Pf
(C) FOOD EMPLOYEE and supervisory training plan that addresses the FOOD safety issues of concern;
(D) A statement of standard operating procedures for the plan under consideration including clearly
identifying:
(1) Each CRITICAL CONTROL POINT, Pf
(2) The CRITICAL LIMITS for each CRITICAL CONTROL POINT, Pf
(3) The method and frequency for monitoring and controlling each CRITICAL CONTROL POINT by the
FOOD EMPLOYEE designated by the PERSON IN CHARGE, Pf
(4) The method and frequency for the PERSON IN CHARGE to routinely verify that the FOOD EMPLOYEE is
following standard operating procedures and monitoring CRITICAL CONTROL POINTS, Pf
(5) Action to be taken by the PERSON IN CHARGE if the CRITICAL LIMITS for each CRITICAL CONTROL POINT
are not met, Pf and
(6) Records to be maintained by the PERSON IN CHARGE to demonstrate that the HACCP PLAN is
properly operated and managed; Pf and
(E) Additional scientific data or other information, as required by the REGULATORY AUTHORITY, supporting
the determination that FOOD safety is not compromised by the proposal. Pf
122
CONFIDENTIALITY
8-202.10 TRADE SECRETS
The REGULATORY AUTHORITY shall treat as confidential in accordance with LAW, information that meets the
criteria specified in LAW for a trade secret and is contained on inspection report forms and in the plans and
specifications submitted as specified under §§ 8-201.12 and 8-201.14.
CONSTRUCTION INSPECTION AND APPROVAL
8-203.10 PREOPERATIONAL INSPECTIONS
The REGULATORY AUTHORITY shall conduct one or more preoperational inspections to verify that the FOOD
ESTABLISHMENT is constructed and equipped in accordance with the APPROVED plans and APPROVED
modifications of those plans, has established standard operating procedures as specified under ¶ 8-
201.12(E), and is in compliance with LAW and this Code.
8-3 PERMIT TO OPERATE
SUBPARTS 8-301 Requirement
8-302 Application Procedure
8-303 Issuance
8-304 Conditions of Retention
REQUIREMENT
8-301.11 PREREQUISITE FOR OPERATION
A PERSON may not operate a FOOD ESTABLISHMENT without a valid PERMIT to operate issued by the REGULATORY
AUTHORITY. Pf
APPLICATION PROCEDURE
8-302.11 SUBMISSION 30 CALENDAR DAYS BEFORE PROPOSED OPENING
An applicant shall submit application for a PERMIT at least 30 calendar days before the date planned for
opening a FOOD ESTABLISHMENT or the expiration date of the current PERMIT for an existing facility.
IDAPA 16.02.19.830 APPLICATION FOR A LICENSE
01. To Apply for a FOOD Establishment License. To apply for an Idaho FOOD ESTABLISHMENT LICENSE the
application and fee is submitted to the REGULATORY AUTHORITY as defined in section 110 of these rules.
02. FOOD License Expiration. The LICENSE for an Idaho FOOD ESTABLISHMENT expires on December 31st
of each year.
03. Renewal of License. A renewal application and a LICENSE fee must be submitted to the REGULATORY
AUTHORITY by December 1st of each year for the next calendar year starting January 1st.
04. Summary Suspension of License. A LICENSE may be immediately suspended under Section 831 of
these rules. Reinstatement of a LICENSE after a summary suspension does not require a new
application or fee unless the LICENSE is revoked.
05. Revocation of License. When corrections have been made to a FOOD ESTABLISHMENT whose LICENSE
has been revoked under Section 860 of these rules, a new application and fee must be submitted to
the REGULATORY AUTHORITY.
06. License is Non-transferable. A LICENSE may not be transferred when ownership changes,
according to Section 8-304.20, of the 2013 Food Code. The new owner must apply for their own
LICENSE.
123
8-302.12 FORM OF SUBMISSION
A PERSON desiring to operate a FOOD ESTABLISHMENT shall submit to the REGULATORY AUTHORITY a written
application for a PERMIT on a form provided by the REGULATORY AUTHORITY.
8-302.13 QUALIFICATIONS AND RESPONSBILITIES OF APPLICANTS
To qualify for a PERMIT, an applicant shall:
(A) Be an owner of the FOOD ESTABLISHMENT or an officer of the legal ownership;
(B) Comply with the requirements of this Code;
(C) As specified under § 8-402.11, agree to allow access to the FOOD ESTABLISHMENT and to provide
required information; and
(D) Pay the applicable PERMIT fees at the time the application is submitted.
8-302.14 CONTENTS OF THE APPLICATION
The application shall include:
(A) The name, birth date, mailing address, telephone number, and signature of the PERSON applying for the
PERMIT and the name, mailing address, and location of the FOOD ESTABLISHMENT;
(B) Information specifying whether the FOOD ESTABLISHMENT is owned by an association, corporation,
individual, partnership, or other legal entity;
(C) A statement specifying whether the FOOD ESTABLISHMENT:
(1) Is mobile or stationary and temporary or permanent, and
(2) Is an operation that includes one or more of the following:
(a) Prepares, offers for sale, or serves TIME/TEMPERATURE CONTROL FOR SAFETY FOOD:
(i.) Only to order upon a CONSUMER'S request,
(ii.) In advance in quantities based on projected CONSUMER demand and discards FOOD
that is not sold or served at an APPROVED frequency, or
(iii.) Using time as the public health control as specified under § 3-501.19,
(b) Prepares TIME/TEMPERATURE CONTROL FOR SAFETY FOOD in advance using a FOOD preparation
method that involves two or more steps which may include combining
TIME/TEMPERATURE CONTROL FOR SAFETY FOOD ingredients; cooking; cooling; reheating; hot
or cold holding; freezing; or thawing,
(c) Prepares FOOD as specified under Subparagraph (C)(2)(b) of this section for delivery to
and consumption at a location off the PREMISES of the FOOD ESTABLISHMENT where it is
prepared,
(d) Prepares FOOD as specified under Subparagraph (C)(2)(b) of this section for service to a
HIGHLY SUSCEPTIBLE POPULATION,
(e) Prepares only FOOD that is not TIME/TEMPERATURE CONTROL FOR SAFETY FOOD, or
(f) Does not prepare, but offers for sale only prePACKAGED FOOD that is not TIME/TEMPERATURE
CONTROL FOR SAFETY FOOD;
(D) The name, title, address, and telephone number of the PERSON directly responsible for the FOOD
ESTABLISHMENT;
(E) The name, title, address, and telephone number of the PERSON who functions as the immediate
supervisor of the PERSON specified under ¶ (D) of this section such as the zone, district, or regional
supervisor;
(F) The names, titles, and addresses of:
(1) The PERSONS comprising the legal ownership as specified under ¶ (B) of this section including
the owners and officers, and
124
(2) The local resident agent if one is required based on the type of legal ownership;
(G) A statement signed by the applicant that:
(1) Attests to the accuracy of the information provided in the application, and
(2) Affirms that the applicant will:
(a) Comply with this Code, and
(b) Allow the REGULATORY AUTHORITY access to the ESTABLISHMENT as specified under § 8-
402.11 and to the records specified under §§ 3-203.12 and 5-205.13 and Subparagraph
8-201.14(D)(6); and
(H) Other information required by the REGULATORY AUTHORITY.
ISSUANCE
8-303.10 NEW, CONVERTED, OR REMODELED ESTABLISHMENTS
For FOOD ESTABLISHMENTS that are required to submit plans as specified under
§ 8-201.11 the REGULATORY AUTHORITY shall issue a PERMIT to the applicant after:
(A) A properly completed application is submitted;
(B) The required fee is submitted;
(C) The required plans, specifications, and information are reviewed and APPROVED; and
(D) A preoperational inspection as specified in § 8-203.10 shows that the ESTABLISHMENT is built or
remodeled in accordance with the APPROVED plans and specifications and that the ESTABLISHMENT is in
compliance with this Code.
8-303.20 EXISTING ESTABLISHMENTS, PERMIT RENEWAL, AND CHANGE OF OWNERSHIP
The REGULATORY AUTHORITY may renew a PERMIT for an existing FOOD ESTABLISHMENT or may issue a PERMIT to a
new owner of an existing FOOD ESTABLISHMENT after a properly completed application is submitted, reviewed,
and APPROVED, the fees are paid, and an inspection shows that the ESTABLISHMENT is in compliance with this
Code.
8-303.30 DENIAL OF APPLICATION FOR PERMIT, NOTICE
If an application for a PERMIT to operate is denied, the REGULATORY AUTHORITY shall provide the applicant with
a notice that includes:
(A) The specific reasons and Code citations for the PERMIT denial;
(B) The actions, if any, that the applicant must take to qualify for a PERMIT; and
(C) Advisement of the applicant's right of appeal and the process and time frames for appeal that are
provided in LAW.
CONDITIONS OF RETENTION
8-304.10 RESPONSIBILITIES OF THE REGULATORY AUTHORITY
(A) At the time a PERMIT is first issued, the REGULATORY AUTHORITY shall provide to the PERMIT HOLDER a copy
of this Code so that the PERMIT HOLDER is notified of the compliance requirements and the conditions of
retention, as specified under § 8-304.11, that are applicable to the PERMIT.
(B) Failure to provide the information specified in ¶ (A) of this section does not prevent the REGULATORY
AUTHORITY from taking authorized action or seeking remedies if the PERMIT HOLDER fails to comply with
this Code or an order, warning, or directive of the REGULATORY AUTHORITY.
125
8-304.11 RESPONSBILITIES OF THE PERMIT HOLDER
Upon acceptance of the PERMIT issued by the REGULATORY AUTHORITY, the PERMIT HOLDER in order to retain the
permit shall:
(A) Post the PERMIT in a location in the FOOD ESTABLISHMENT that is conspicuous to CONSUMERS;
(B) Comply with the provisions of this Code including the conditions of a granted VARIANCE as specified
under § 8-103.12, and APPROVED plans as specified under § 8-201.12;
(C) If a FOOD ESTABLISHMENT is required under § 8-201.13 to operate under a HACCP PLAN, comply with the
plan as specified under § 8-103.12;
(D) Immediately contact the REGULATORY AUTHORITY to report an illness of a FOOD EMPLOYEE or CONDITIONAL
EMPLOYEE as specified under § 2-201.11(B);
(E) Immediately discontinue operations and notify the REGULATORY AUTHORITY if an IMMINENT HEALTH HAZARD
may exist as specified under § 8-404.11;
(F) Allow representatives of the REGULATORY AUTHORITY access to the FOOD ESTABLISHMENT as specified
under § 8-402.11.
(G) Replace existing facilities and EQUIPMENT specified in § 8-101.10 with facilities and EQUIPMENT that
comply with this Code if:
(1) The REGULATORY AUTHORITY directs the replacement because the facilities and EQUIPMENT
constitute a public health HAZARD or nuisance or no longer comply with the criteria upon which
the facilities and EQUIPMENT were accepted,
(2) The REGULATORY AUTHORITY directs the replacement of the facilities and EQUIPMENT because of a
change of ownership, or
(3) The facilities and EQUIPMENT are replaced in the normal course of operation;
(H) Comply with directives of the REGULATORY AUTHORITY including time frames for corrective actions
specified in inspection reports, notices, orders, warnings, and other directives issued by the
REGULATORY AUTHORITY in regard to the PERMIT HOLDER'S FOOD ESTABLISHMENT or in response to
community emergencies;
(I) Accept notices issued and served by the REGULATORY AUTHORITY according to LAW; and
(J) Be subject to the administrative, civil, injunctive, and criminal remedies authorized in LAW for failure
to comply with this Code or a directive of the REGULATORY AUTHORITY, including time frames for
corrective actions specified in inspection reports, notices, orders, warnings, and other directives.
(K) Notify customers that a copy of the most recent establishment inspection report is available upon
request by posting a sign or placard in a location in the food establishment that is conspicuous to
customers or by another method acceptable to the REGULATORY AUTHORITY.
8-304.20 PERMITS NOT TRANSFERABLE
A PERMIT may not be transferred from one PERSON to another PERSON, from one FOOD ESTABLISHMENT to another,
or from one type of operation to another if the FOOD operation changes from the type of operation specified
in the application as specified under ¶ 8-302.14(C) and the change in operation is not APPROVED.
IDAPA 16.02.19.831 SUMMARY SUSPENSION OF LICENSE
The REGULATORY AUTHORITY may temporarily suspend a LICENSE to operate a FOOD ESTABLISHMENT when it
determines that an IMMINENT HEALTH HAZARD exists.
01. Reasons a Summary Suspension May be Issued.
When a FOOD ESTABLISHMENT does not follow the principles of FOOD safety, or FOODborne illness is
found, or an environmental HAZARD exists and public safety cannot be assured by the continued
operation of the FOOD ESTABLISHMENT, a summary suspension may be issued. The following are some
reasons the REGULATORY AUTHORITY may determine a summary suspension is necessary:
(a) Inspection of the FOOD ESTABLISHMENT shows uncorrected PRIORITY VIOLATIONS;
126
(b) Examination of FOOD shows the FOOD is unsafe;
(c) Review of records shows that proper steps for FOOD safety have not been met;
(d) EMPLOYEES working with FOOD are suspected of having a disease that is communicable
through FOOD; or
(e) An IMMINENT HEALTH HAZARD exists.
02. Priority Notice is Not Required for a Summary Suspension.
Upon providing written notice of summary suspension to the LICENSE HOLDER or PERSON IN CHARGE, the
REGULATORY AUTHORITY may suspend a FOOD ESTABLISHMENT'S LICENSE without prior warning, notice of
hearing, or hearing.
03. Written Notice of Summary Suspension.
The REGULATORY AUTHORITY must give the LICENSE HOLDER or PERSON IN CHARGE written notice when
suspending a LICENSE. The notice must include the following:
(a) The specific reasons or violations the summary suspension is issued for with reference to
the section of the 2013 FOOD Code which is in violation:
(b) A statement notifying the FOOD ESTABLISHMENT its LICENSE is suspended and that all FOOD
operations are to cease immediately;
(c) The name and address of the REGULATORY AUTHORITY representative to whom a written
request for re-inspection can be made and who can certify the reasons for the suspension
have been eliminated;
(d) A statement notifying the FOOD ESTABLISHMENT of its right to an information hearing with the
REGULATORY AUTHORITY upon submission of a written request within fifteen (15) days of
receiving the summary suspension notice; and
(e) A statement informing the FOOD ESTABLISHMENT that proceedings for revocation of the LICENSE
shall be initiated by the REGULATORY AUTHORITY after suspension, if violations are not
immediately corrected.
(f) The right to request an appeal to the DEPARTMENT as provided in Section 861 of these rules.
04. Length of Summary Suspension
The suspension will remain in effect until the conditions cited in the notice of suspension no longer
exist and their elimination has been confirmed by the REGULATORY AUTHORITY during a re-inspection.
05. Re-inspection of FOOD ESTABLISHMENT
The REGULATORY AUTHORITY will conduct a re-inspection of the FOOD ESTABLISHMENT within two (2)
working days of receiving a written request stating the conditions for the suspension no longer
exist.
06. Reinstatement of License
The REGULATORY AUTHORITY will immediately reinstate the suspended LICENSE if the re-inspection
determines the public health HAZARD no longer exists. The REGULATORY AUTHORITY will provide a
written notice of reinstatement to the LICENSE HOLDER or PERSON IN CHARGE.
127
8-4 INSPECTION AND CORRECTION VIOLATIONS
SUBPARTS 8-401 Frequency
8-402 Competency and Access
8-403 Report of Findings
8-404 Imminent Health Hazard
8-405 Violation of PRIORITY ITEM or PRIORITY FOUNDATION ITEM
8-406 CORE Violation
FREQUENCY
8-401.10 ESTABLISHING INSPECTION INTERVAL
IDAPA 16.02.19.840 INSPECTIONS AND CORRECTION OF VIOLATIONS
01. Inspection Interval Section 8-401.10(A): Modification to 8-401.10(A). Except as specified in 8-
401.10(C), the REGULATORY AUTHORITY must inspect a FOOD ESTABLISHMENT at least once a year.
02. Modification to Section 8-401.10(B): This section has not been adopted.
03. Adoption of Section 8-401-10(C) This section is adopted as published:
(C) The REGULATORY AUTHORITY shall periodically inspect throughout its PERMIT period a TEMPORARY FOOD
ESTABLISHMENT that prepares, sells, or serves unPACKAGED TIME/TEMPERATURE CONTROL FOR SAFETY FOOD and
that:
(1) Has improvised rather than permanent facilities or EQUIPMENT for accomplishing functions such as
handwashing, FOOD preparation and protection, FOOD temperature control, WAREWASHING, providing
DRINKING WATER, waste retention and disposal, and insect and rodent control; or
(2) Has inexperienced FOOD EMPLOYEES.
8-401.20 PERFORMANCE- AND RISK-BASED
Within the parameters specified in § 8-401.10, the REGULATORY AUTHORITY shall prioritize, and conduct more
frequent inspections based upon its assessment of a FOOD ESTABLISHMENT'S history of compliance with this
Code and the ESTABLISHMENT'S potential as a vector of FOODborne illness by evaluating:
(A) Past performance, for nonconformance with Code or HACCP PLAN requirements that are PRIORITY
ITEMS or PRIORITY FOUNDATION ITEMS;
(B) Past performance, for numerous or repeat violations of Code or HACCP PLAN requirements that are
CORE ITEMS;
(C) Past performance, for complaints investigated and found to be valid;
(D) The HAZARDS associated with the particular FOODS that are prepared, stored, or served;
(E) The type of operation including the methods and extent of FOOD storage, preparation, and service;
(F) The number of people served; and
(G) Whether the population served is a HIGHLY SUSCEPTIBLE POPULATION.
COMPETENCY
8-402.10 COMPETENCY OF INSPECTORS
An authorized representative of the REGULATORY AUTHORITY who inspects a FOOD ESTABLISHMENT or conducts
plan review for compliance with this Code shall have the knowledge, skills, and ability to adequately perform
the required duties.
128
ACCESS
8-402.11 ALLOWED AT REASONABLE TIMES AFTER DUE NOTICE
After the REGULATORY AUTHORITY presents official credentials and provides notice of the purpose of, and an
intent to conduct, an inspection, the PERSON IN CHARGE shall allow the REGULATORY AUTHORITY to determine if
the FOOD ESTABLISHMENT is in compliance with this Code by allowing access to the ESTABLISHMENT, allowing
inspection, and providing information and records specified in this Code and to which the REGULATORY
AUTHORITY is entitled according to LAW, during the FOOD ESTABLISHMENT'S hours of operation and other
reasonable times.
8-402.20 REFUSAL, NOTIFICATION OF RIGHT TO ACCESS, AND FINAL REQUEST FOR ACCESS
If a PERSON denies access to the REGULATORY AUTHORITY, the REGULATORY AUTHORITY shall:
(A) Inform the PERSON that:
(1) The PERMIT HOLDER is required to allow access to the REGULATORY AUTHORITY as specified under §
8-402.11 of this Code,
(2) Access is a condition of the acceptance and retention of a FOOD ESTABLISHMENT PERMIT to operate
as specified under ¶ 8-304.11(F), and
(3) If access is denied, an order issued by the appropriate authority allowing access, hereinafter
referred to as an inspection order, may be obtained according to LAW; and
(B) Make a final request for access.
8-402.30 REFUSAL, REPORTING
If after the REGULATORY AUTHORITY presents credentials and provides notice as specified under § 8-402.11,
explains the authority upon which access is requested, and makes a final request for access as specified in §
8-402.20, the PERSON IN CHARGE continues to REFUSE access, the REGULATORY AUTHORITY shall provide details of
the denial of access on an inspection report form.
8-402.40 INSPECTION ORDER TO GAIN ACCESS
If denied access to a FOOD ESTABLISHMENT for an authorized purpose and after complying with 8-403.20, the
REGULATORY AUTHORITY may issue, or apply for the issuance of, an inspection order to gain access as provided
in LAW.
REPORT OF FINDINGS
8-403.10 DOCUMENTING INFORMATION AND OBSERVATIONS
The REGULATORY AUTHORITY shall document on an inspection report form:
(A) Administrative information about the FOOD ESTABLISHMENT'S legal identify, street and mailing
addresses, type of ESTABLISHMENT and operation as specified under ¶ 8-302.14(C), inspection date, and
other information such as type of water supply and SEWAGE disposal, status of the PERMIT, and
personnel certificates that may be required; and
(B) Specific factual observations of violative conditions or other deviations from this Code that require
correction by the PERMIT HOLDER including:
(1) Failure of the PERSON IN CHARGE to demonstrate the knowledge of foodborne illness prevention,
application of HACCP principles, and the requirements of this Code as specified under § 2-
102.11,
(2) Failure of FOOD EMPLOYEES, CONDITIONAL EMPLOYEES, and the PERSON IN CHARGE to report a disease,
or medical condition as specified under ¶¶ 2-201.11(B) and (D), and
(3) Nonconformance with PRIORITY ITEMS OR PRIORITY FOUNDATION ITEMS of this Code,
129
(4) Failure of the appropriate FOOD EMPLOYEES to demonstrate their knowledge of, and ability to
perform in accordance with, the procedural, monitoring, verification, and corrective action
practices required by the REGULATORY AUTHORITY as specified under Subparagraph 8-103.12,
(5) Failure of the PERSON IN CHARGE to provide records required by the REGULATORY AUTHORITY for
determining conformance with a HACCP PLAN as specified under Subparagraph 8-201.14(D)(6),
and
(6) Nonconformance with CRITICAL LIMITS of a HACCP PLAN.
IDAPA 16.02.19.841 INSPECTION SCORES
The REGULATORY AUTHORITY must provide the LICENSE HOLDER an inspection report with a total score indicating
the number of RISK FACTOR VIOLATIONS and the number of repeat RISK FACTOR VIOLATIONS added together.
Repeat violations are those observed during the last inspection. The inspection report will also score the
total number of GOOD RETAIL PRACTICE violations and the number of repeat GOOD RETAIL PRACTICE violations.
These scores will be used to determine if a follow-up inspection or a written report of correction is needed to
verify corrections have been made.
01. Medium-Risk FOOD ESTABLISHMENT
If the RISK FACTOR VIOLATIONS exceed three (3), or GOOD RETAIL PRACTICE violations exceed six (6), an on-
site follow-up inspection is required for verification of correction by the REGULATORY AUTHORITY.
02. High-Risk FOOD ESTABLISHMENT
If the RISK FACTOR VIOLATIONS exceed five (5), or GOOD RETAIL PRACTICE violations exceed eight (8), an
on-site follow-up inspection is required for verification of correction by the REGULATORY AUTHORITY.
03. Written Violation Correction Report
A written violation correction report by the LICENSE HOLDER may be provided to the REGULATORY
AUTHORITY if the total inspection score of the FOOD ESTABLISHMENT does not exceed those listed in
Section 845 of these rules. The report must be mailed within five (5) days of the correction date
identified on the inspection report.
8-403.20 SPECIFYING TIME FRAME FOR CORRECTIONS
The REGULATORY AUTHORITY shall specify on the inspection report form the time frame for correction of the
violations as specified under § 8-404.11, § 8-405.11, and § 8-406.11.
8-403.30 ISSUING REPORT AND OBTAINING ACKNOWLEDGEMENT OF RECEIPT
At the conclusion of the inspection and according to LAW, the REGULATORY AUTHORITY shall provide a copy of
the completed inspection report and the notice to correct violations to the PERMIT HOLDER or to the PERSON IN
CHARGE, and request a signed acknowledgement of receipt.
8-403.40 REFUSAL TO SIGN ACKNOWLEDGEMENT
The REGULATORY AUTHORITY shall:
(A) Inform a PERSON who declines to sign an acknowledgment of receipt of inspectional findings as
specified in § 8-403.30 that:
(1) An acknowledgment of receipt is not an agreement with findings,
(2) Refusal to sign an acknowledgment of receipt will not affect the PERMIT HOLDER'S obligation to
correct the violations noted in the inspection report within the time frames specified, and
(3) A refusal to sign an acknowledgment of receipt is noted in the inspection report and conveyed
to the REGULATORY AUTHORITY'S historical record for the FOOD ESTABLISHMENT; and
(B) Make a final request that the PERSON IN CHARGE sign an acknowledgement receipt of inspectional
findings.
8-403.50 PUBLIC INFORMATION
Except as specified in § 8-202.10, the REGULATORY AUTHORITY shall treat the inspection report as a public
document and shall make it available for DISCLOSURE to a PERSON who requests it as provided in LAW.
130
IMMINENT HEALTH HAZARD
8-404.11 CEASING OPERATIONS AND REPORTING
(A) Except as specified in ¶ (B) of this section, a PERMIT HOLDER shall immediately discontinue operations
and notify the REGULATORY AUTHORITY if an IMMINENT HEALTH HAZARD may exist because of an emergency
such as a fire, flood, extended interruption of electrical or water service, SEWAGE backup, misuse of
POISONOUS OR TOXIC MATERIALS, onset of an apparent foodborne illness outbreak, gross insanitary
occurrence or condition, or other circumstance that may endanger public health. P
(B) A PERMIT HOLDER need not discontinue operations in an area of an ESTABLISHMENT that is unaffected by
the IMMINENT HEALTH HAZARD.
8-404.12 RESUMPTION OF OPERATIONS
If operations are discontinued as specified under § 8-404.11 or otherwise according to LAW, the PERMIT
HOLDER shall obtain approval from the REGULATORY AUTHORITY before resuming operations.
VIOLATION OF PRIORITY ITEM OR PRIORITY FOUNDATION ITEM – PRIORITY
VIOLATION
8-405.11 TIMELY CORRECTION
(A) Except as specified in ¶ (B) of this section, a PERMIT HOLDER shall at the time of inspection a correct a
violation of a PRIORITY ITEM or PRIORITY FOUNDATION ITEM of this Code and implement corrective
actions for a HACCP PLAN provision that is not in compliance with its CRITICAL LIMIT. Pf
(B) Considering the nature of the potential HAZARD involved and the complexity of the corrective action
needed, the REGULATORY AUTHORITY may agree to or specify a longer time frame, not to exceed:
(1) IDAPA 16.02.19.840.04a – Delete Section 8-405.11(B)(1)
(2) 10 calendar days after the inspection, for the PERMIT HOLDER to correct violations of a PRIORITY or
PRIORITY-FOUNDATION or HACCP PLAN deviations.
8-405.20 VERIFICATION AND DOCUMENTATION OF CORRECTION
(A) After observing at the time of inspection a correction of a violation of a PRIORITY ITEM or PRIORITY
FOUNDATION ITEM or a HACCP PLAN deviation, the REGULATORY AUTHORITY shall enter the violation and
information about the corrective action on the inspection report
(B) As specified under ¶ 8-405.11(B), after receiving notification that the PERMIT HOLDER has corrected a
violation of a PRIORITY ITEM or PRIORITY FOUNDATION ITEM or HACCP PLAN deviation, or at the end
of the specified period of time, the REGULATORY AUTHORITY shall verify correction of the violation,
document the information on an inspection report, and enter the report in the REGULATORY AUTHORITY'S
records.
IDAPA 16.02.19.845 VERIFICATION AND DOCUMENTATION OF CORRECTION
In additional to Section 8-405.20 of the 2013 FOOD Code, the on-site follow-up inspection may not be
required for verification of correction if the REGULATORY AUTHORITY chooses to accept a written report of
correction from the LICENSE HOLDER.
01. Written Report of Correction.
The REGULATORY AUTHORITY may choose to accept a written report of correction from the LICENSE
HOLDER stating that specific violations have been corrected. The LICENSE HOLDER must submit this
report to the REGULATORY AUTHORITY within five (5) days after the correction date identified on the
inspection report.
(a) Medium-Risk FOOD ESTABLISHMENT. If the RISK FACTOR VIOLATIONS do not exceed three (3), or the
GOOD RETAIL PRACTICE violations do not exceed six (6), a follow-up inspection is not required for
verification of correction.
131
(b) High-Risk FOOD ESTABLISHMENT. If the RISK FACTOR VIOLATIONS do not exceed five (5), or the GOOD
RETAIL PRACTICE violations do not exceed eight (8), a follow-up inspection is not required for
verification of correction.
02. Risk Control Plan. The REGULATORY AUTHORITY may require the development of a RISK CONTROL PLAN
as verification of correction. The RISK CONTROL PLAN must provide documentation on how the LICENSE
HOLDER will obtain long term correction of PRIORITY VIOLATIONS that are repeated violations,
including how control will be monitored and who will be responsible.
CORE VIOLATION
8-406.11 TIME FRAME FOR CORRECTION
(A) Except as specified in ¶ (B) of this section, the PERMIT HOLDER shall correct CORE ITEMS by a date and
time agreed to or specified by the REGULATORY AUTHORITY but no later than 90 calendar days after the
inspection.
(B) The REGULATORY AUTHORITY may APPROVE a compliance schedule that extends beyond the time limits
specified under ¶ (A) of this section if a written schedule of compliance is submitted by the PERMIT
HOLDER and no health HAZARD exists or will result from allowing an extended schedule for compliance.
IDAPA 16.02.19.850 ENFORCEMENT INSPECTIONS
01. Follow-up Inspection.
If a follow-up inspection reveals that a PRIORITY, PRIORITY_FOUNDATION, or CORE VIOLATIONS
identified on a previous inspection have not been corrected or still exist and ENFORCEMENT INSPECTION
may be made.
02. Written Notice.
The LICENSE HOLDER will receive written notice on the inspection form of the specific date for an
ENFORCEMENT INSPECTION. This date must be within fifteen (15) days of the current or follow-up
inspection.
03. Enforcement Inspections on CONSENT ORDER.
When compliance conference results in a CONSENT ORDER and includes a compliance schedule to
correct violations without further regulatory action, all inspections by the REGULATORY AUTHORITY to
satisfy the compliance schedule will be ENFORCEMENT INSPECTIONs until the next annual inspection.
04. Regulatory Action.
If the violations have not been corrected by the date of the ENFORCEMENT INSPECTION, regulatory action
will be initiated to revoke or suspend the LICENSE issued to the FOOD ESTABLISHMENT.
132
8-5 PREVENTION OF FOODBORNE DISEASE TRANSMISSION BY EMPLOYEES
SUBPART 8-501 Investigation and Control
INVESTIGATION AND CONTROL
8-501.10 OBTAINING INFORMATION: PERSONAL HISTORY OF ILLNESS, MEDICAL
EXAMINATION, AND SPECIMEN ANALYSIS
The REGULATORY AUTHORITY shall act when it has reasonable cause to believe that a FOOD EMPLOYEE or
CONDITIONAL EMPLOYEE has possibly transmitted disease; may be infected with a disease in a communicable
form that is transmissible through FOOD; may be a carrier of infectious agents that cause a disease that is
transmissible through FOOD; or is affected with a boil, an infected would, or acute respiratory infection, by:
(A) Securing a confidential medical history of the FOOD EMPLOYEE or CONDITIONAL EMPLOYEE suspected of
transmitting disease or making other investigations as deemed appropriate; and
(B) Requiring appropriate medical examinations, including collection of specimens for laboratory
analysis, of a suspected FOOD EMPLOYEE or CONDITIONAL EMPLOYEE.
8-501.20 RESTRICTION OR EXCLUSION OF FOOD EMPLOYEE, OR SUMMARY SUSPENSION OF
PERMIT
Based on the finding of an investigation related to a FOOD EMPLOYEE or CONDITIONAL EMPLOYEE who is suspected
of being infected or diseased, the REGULATORY AUTHORITY may issue an order to the suspected FOOD EMPLOYEE,
CONDITIONAL EMPLOYEE or PERMIT HOLDER instituting one or more of the following control measures:
(A) RESTRICTING the FOOD EMPLOYEE or CONDITIONAL EMPLOYEE;
(B) EXCLUDING the FOOD EMPLOYEE or CONDITIONAL EMPLOYEE; or
(C) Closing the FOOD ESTABLISHMENT by summarily suspending a PERMIT to operate in accordance with LAW.
8-501.30 RESTRICTION OR EXCLUSION ORDER: WARNING OR HEARING NOT REQUIRED,
INFORMATION REQUIRED IN ORDER
Based on the findings of the investigation as specified in ¶ 8-501.10 and to control disease transmission, the
REGULATORY AUTHORITY may issue an order of RESTRICTION or EXCLUSION to a suspected FOOD EMPLOYEE or the
PERMIT HOLDER without prior warning, notice of a hearing, or a hearing if the order:
(A) States the reasons for the RESTRICTION of EXCLUSION that is ordered:
(B) States the evidence that the FOOD EMPLOYEE or PERMIT HOLDER shall provide in order to demonstrate that
the reasons for the RESTRICTION or EXCLUSION are eliminated;
(C) States that the suspected FOOD EMPLOYEE or the PERMIT HOLDER may request an appeal hearing by
submitting a timely request as provided in LAW; and
(D) Provides the name and address of the REGULATORY AUTHORITY representative to whom a request for an
appeal hearing may be made.
8-501.40 REMOVAL OF EXCLUSIONS AND RESTRICTIONS
The REGULATORY AUTHORITY shall release a FOOD EMPLOYEE, or CONDITIONAL EMPLOYEE from RESTRICTION or
EXCLUSION according to LAW and the conditions specified under § 2-201.13.
IDAPA 16.025.19.851 ENFORCEMENT PROCEDURES FOR ADULTERATED OR MISBRANDED
FOOD
The REGULATORY AUTHORITY may order the LICENSE HOLDER or other PERSON who has custody of ADULTERATED or
misbranded FOOD to destroy, denature or recondition ADULTERATED or misbranded FOOD according to Section
37-118, Idaho Code. The following procedures apply:
01. Servicing an EMBARGO Order. An EMBARGO order must be served by one (1) of the following ways:
133
(a) Delivered personally to the LICENSE HOLDER or PERSON IN CHARGE of the FOOD ESTABLISHMENT; or
(b) Posted at a public entrance to the FOOD ESTABLISHMENT provided a copy of the notice is sent by
first-class mail to the LICENSE HOLDER or the PERSON IN CHARGE of the EMBARGOED FOOD.
02. The EMBARGO Order is Effective When Served. The EMBARGO order is effective at the time the
notice is received by the LICENSE HOLDER or the time of posting the notice.
03. Tagging EMBARGOED FOOD. The REGULATORY AUTHORITY must securely place as official tag or label on
FOOD or containers identified as FOOD subject to a hold order.
04. Storage of EMBARGOED FOOD. The REGULATORY AUTHORITY shall allow storage of FOOD under
conditions specified in the EMBARGO order, unless storage is not possible without RISK to the public
health. The REGULATORY AUTHORITY may order immediate destruction of the ADULTERATED or
misbranded FOOD for public safety.
05. Removal of EMBARGO Tag or Label. The removal of the EMBARGO tag, label or other identification
from the suspected FOOD is not ADULTERATED or misbranded must be done by the REGULATORY
AUTHORITY.
06. EMBARGO Release. The issue of release and removal of the EMBARGO tag, label, or other identification
from the suspected FOOD when it is not ADULTERATED or misbranded must be done by the REGULATORY
AUTHORITY.
IDAPA 16.02.19.860 REVOCATION OF LICENSE
The REGULATORY AUTHORITY may revoke the LICENSE issued to a FOOD ESTABLISHMENT when the LICENSE HOLDER
fails to comply with these rules or the operation is a substantial HAZARD to public health.
01. Reasons a License May be Revoked
(a) The LICENSE HOLDER or EMPLOYEE in charge of the FOOD ESTABLISHMENT violates any term or
condition in Section 8-304.11 of the 2013 FOOD Code.
(b) Access to the facility is denied or obstructed by an EMPLOYEE, agent, contractor, or other
representative during the performance of the REGULATORY AUTHORITY'S duties. It is not necessary
for the REGULATORY AUTHORITY to seek an inspection order as permitted in Section 8-402.40 of the
2013 FOOD Code, before proceeding revocation.
(c) A public health HAZARD or PRIORITY VIOLATION remains uncorrected after being identified by the
REGULATORY AUTHORITY and an ENFORCEMENT INSPECTION confirms the violation or HAZARD still
exists. See section 850 of these rules on ENFORCEMENT INSPECTIONS;
(d) A CORE VIOLATION remains uncorrected after being identified by the REGULATORY AUTHORITY and an
ENFORCEMENT INSPECTION confirms the violation still exists. See Section 845 of these rules on
verification and documentation of correction.
(e) Failure to comply with any CONSENT ORDER issued after a compliance conference. See section 861
of these rules.
(f) Failure to comply with a REGULATORY AUTHORITY'S immediate suspension order when there is an
IMMINENT HEALTH HAZARD. See Section 831 of these rules on summary SUSPENSION of a LICENSE.
(g) Failure to comply with an EMBARGO order. See Section 851 of these rules on ADULTERATED and
misbranded FOOD.
(h) Failure to comply with a REGULATORY AUTHORITY order issued when an EMPLOYEE is suspected of
having a communicable disease. See Chapter 2 of the 2013 Food Code on EMPLOYEE health.
02. Notice to Revoke a License.
The REGULATORY AUTHORITY must notify the LICENSE HOLDER of the FOOD ESTABLISHMENT in writing of the
intended revocation of the LICENSE. See Section 861 of these rules for appeal process. The notice
must include the Subsections 860.02.a through 860.02.c of this rule.
(a) The specific reasons and sections of the Idaho FOOD Code which are in violation and the cause
for action of the revocation and;
134
(b) The right of the LICENSE HOLDER to request in writing a compliance conference with the
REGULATORY AUTHORITY within fifteen (15) days of the notice; and
(c) The right of the LICENSE HOLDER to appeal in writing to the DEPARTMENT of Health and Welfare.
See Subsection 861.02 of these rules.
(d) The following is sufficient notification of the LICENSE HOLDER'S appeal rights: "You have the right
to request in writing a compliance conference with (name and address of designated health
district official) within fifteen (15) days of the receipt of this notice. You may also appeal the
revocation of your LICENSE to the DIRECTOR of the DEPARTMENT of Health and Welfare by filing a
written appeal with the DEPARTMENT as provided in IDAPA 16.05.03 "Rules Governing Contested
Case Proceeding and Declaratory Rulings," within fifteen (15) days of the receipt of this notice,
or if a timely request is made for a compliance conference and the matter is not resolved by a
CONSENT ORDER, within five (5) working days following the conclusion of the compliance
conference."
03. Effective Date of Revocation.
The revocation will be effective fifteen (15) days following service of notice, unless a timely request
for a compliance conference is made or an appeal is filed. If a compliance conference is requested
and the matter is not resolved by a CONSENT ORDER, the revocation will be effective five (5) working
days following the end of the conference, unless an appeal is made to the DIRECTOR of the
DEPARTMENT of Health and Welfare within that time. See Section 861 of these rules for compliance
conference, CONSENT ORDER, and appeal procedures.
IDAPA 16.02.19.861 APPEAL PROCESS
A LICENSE HOLDER may appeal a summary suspension, notice of revocation, other action, or failure to act by
the REGULATORY AUTHORITY which adversely affects the LICENSE HOLDER. A summary suspension or other
emergency order is not stayed during the appeal process.
01. Compliance Conference. The LICENSE HOLDER may request in writing a compliance conference with
the REGULATORY AUTHORITY within fifteen (15) days of receipt of the notice or action by the
REGULATORY AUTHORITY. If a timely request for a compliance conference is made, a compliance
conference will be scheduled within twenty (20) days and conducted in an informal manner by the
REGULATORY AUTHORITY. At the compliance conference the LICENSE HOLDER may explain the
circumstances of the alleged violations and propose a resolution for the matter.
(a) If the compliance conference results in an agreement between the license holder and the
REGULATORY AUTHORITY to remedy circumstances giving rise to the action and to assure future
compliance, the agreement must be put in written form and signed by both parties. This written
agreement shall constitute an enforceable CONSENT ORDER.
(b) Unless otherwise specifically stated in the CONSENT ORDER, the agreement shall be for the
duration of the existing LICENSE only.
02. Appeal to the Director. The LICENSE HOLDER may appeal in writing to the DIRECTOR of the
DEPARTMENT of Health and Welfare within fifteen (15) days of receipt of the notice of action by the
REGULATORY AUTHORITY, or if a timely request for a compliance conference was made, within five (5)
working days following the completion of the compliance conference.
IDAPA 16.02.19.890 CRIMINAL AND CIVIL PROCEEDINGS
The REGULATORY AUTHORITY may choose to enforce the provisions of these rules and its administrative orders
through the courts.
01. Criminal Proceedings. Misdemeanor proceedings to enforce these rules, federal regulations, and
the enabling statutes may be instituted as provided in Sections 37-117, 37-119, 37-2103, and 56-
1008, Idaho Code. These statutes provide for fines or terms of imprisonment that may be sought
through the court of competent jurisdiction.
02. Civil Proceedings. Civil enforcement actions may be commenced and prosecuted in the district
court in the county where the alleged violation occurred, according to Sections 56-1009, and 56-
1010, Idaho Code. The PERSON who is alleged to have violated any enabling statute, rule, federal
regulation, LICENSE or order may be charged in the court proceeding. This action is brought to
135
compel compliance with these rules, regulations, LICENSE or order for relief or remedies authorized
in the rules.
03. Injunctive Relief. In addition to other remedies provided by LAW, Section 56-1009 allows for a
search warrant to gain access and injunctions to be issued in the name of the state against any
PERSON or entity to enjoin that PERSON or entity from violating these rules, regulations, statues or
administrative orders.
INDEX
aw, definition, 13
Access
allowed after due notice, 129 application for inspection order, 129
notification of right, 129
owner agreement, 129
refusal, 129
Accuracy, 77-78 Acidity. See pH, 22
Accreditation, 32
equipment certification program, 82 manager certification program, 32
Accredited program, 13
Additive, food and color
definition, 13
food upon receipt, 47-48 limitations, 66-67, 117
sulfites, 53
unapproved, protection from, 53
Adulterated
definition, 13 food condition, 44
Air-drying
equipment and utensils, 93
wiping cloths, locations, 94
Air filtration, 102 Air gap. See Backflow Prevention, Plumbing System
Air temperature, 63-64, 77
See also Ambient temperature measuring devices Aisles in work spaces. See Spacing
Alkalinity. See pH
Allergen. See Major food allergen
Alligator. See Fish
Ambient temperature measuring devices, 77 Animal foods, raw
consumer self-service, limitations, 57
2
cooking requirements, 58-61 separation from other foods, 52-53
Animal foods, raw or undercooked, consumer advisory, 71
Animals
commercially raised for food, 46-47, 58
exotic animals, limitations as food source, 47 game, 46-47, 58-59
handling by employees, prohibition
and exception, 43 handwashing after handling, 40-41
live, prohibition and exceptions, 114 wild game, 46-47, 59
Anti-slip floor coverings, 107
Appeal denial of application for operating permit, 125
restriction or exclusion order, 133
Applicant for permit to operate food establishment
information required, 124-125
qualifications, 124 Applicant, responsibility to report illness, 126
Application for operating permit
notice of denial, 125 procedure, 124-125
Application of Code
prevention of health hazards, 120
public health protection, 120
Approved, definition, 13 Area
adjacent to easily movable equipment, 16
behind vending machine kickplates, 77 consumer eating and drinking, 107-108, 114
consumer shopping, 85, 104, 107, 114
designated for eating, drinking, and tobacco
use, 42-43, 108
dining, 92, 114 distressed merchandise, 112
dressing, 111, 113
driving, 106, 109 dry storage, 107
exposed, 107-108
food preparation, 104,105, 113-114
handwashing, sink, 98, 99-100, 107
indoor, construction material, 106-107 light intensity by, 110-111
living, 109
outdoor, construction materials, 106 outside fenced, 114
poisonous or toxic materials, 116-118
prohibited food storage, 56
protected for tank vent, 101
refuse, 103-105 registration for bed and breakfast, 18
requiring drip-free ventilation, 78
self-service, 32-33
separate, for raw foods, 52
servicing, 106-109 shellfish harvesting, 50
sleeping, 109
storage, 103-105 underneath equipment for cleaning, 84-85
underneath fingernails, cleaning, 40
unaffected by imminent health hazard, 313
vending machine, 29, 109
warewashing, 107, 115 waste servicing, 102-103
where unnecessary persons are not allowed, 32
Artificial color or flavor, declaration, 70-71
Asymptomatic carrier, 35-39
Asymptomatic, definition, 13 Attachments, wall and ceilings, cleanability, 107
Authorities, enforcement, 133
Automatic shutoff, vending machines, 79-80
Backflow prevention, plumbing system
air gap, 98
carbonator, 99
knowledge of person in charge, 31 sewage systems, 102-103
water system operation, 97
Backflow prevention device, plumbing system carbonator, 99
copper, use limitation, 75 design standard, 95
location, 96
numbers and capacity, 96-97 operation and maintenance, 99
Backsiphonage. See Backflow
Bacon, slab, storage, 52
Bacteria. See Disease outbreaks caused by
Baffles, internal, for warewashing machine, 80 Bags. See Single-service articles
Bait
fish, 114 station, 118
Bakery products, 71
Balut, definition, 13
Basket, for warewashing equipment, 81, 90-91
Bearings and gear boxes, leakproof, 79 Bed and Breakfast, 9, 18
Beef
consumer self-service, 57 cooking requirement, 58-60
minimum holding times for cooking, 59
oven parameters for cooking, 59
rare or raw, consumer advisory, 71
raw, storage, 52 use of clean equipment, 88-90
use of laundered gloves, 93
whole-muscle, intact, definition, 29 whole-muscle, intact steak, cooking, 59-60
Beef roasts, cooking requirements, 58-59
Beverage
containers, consumer-owned, refilling, 55-56
definition, 13 tubing, separation from stored ice, 79
vending machines, liquid waste disposal, 81
Birds, dead or trapped, removal, 113 Boil. See Lesion, containing pus
Boiler water additives, criteria, 117
Bottled drinking water, definition, 13
source, 96
Botulism. See Clostridium botulinum Bowls. See Tableware
Bread wrappers. See Single-use articles
Buffets, monitoring by food employees, 57
Buildings. See Physical facilities
Bulk food dispensing methods, 57-58
display, protection, 57
labeling requirements, 70-71 liquid, vended, 81
raw animal food, prohibition, 57
unpackaged, labeling exemptions, 71
Bulk milk container dispensing tube, 88
Cabinets
storage, 84, 95, 88, 114
vending machine, 81-82
Calibration, temperature measuring devices, 88 Can openers
design and construction, 77
maintenance and operation, 85
3
on vending machines, design and construction, 79 Cans, number 10. See Single-use articles
Canthaxanthin, 79
Carbonator, 99
Cardboard for recycling, outside storage, 104
Carpeting, floor, restrictions and installation, 107 Carrier, disease. See Asymptomatic carrier
Carry-out utensils. See Single-service articles
Case lot handling equipment, moveability, 81-82 Casing
definition, 13 Cast iron utensils and equipment food-contact
surfaces,
use limitation, 75 Catering operation. See Food establishment
Catsup bottles. See Single-use articles
Ceiling, ceiling coverings, and coatings,
cleanability, 107
Ceramic utensils, lead limitation, 75 Certification number, definition, 13
CFR, definition, 3
Cheese date marking, 64-65
ROP, 69
Chemicals
preservatives, declaration, 70
sanitization of equipment food-contact surfaces and utensils, 92
sanitizers, criteria, 116
washing fruits and vegetables, criteria, 117 working containers, of, 115
Chicken, raw, immersion in ice or water, 54
Children’s menu, 60
China utensils, lead imitation, 74
Chlorine solutions, chemical sanitization, 86-88 CIP
definition, 13
equipment, design and construction, 77 Clams, lightly cooked or raw, consumer advisory, 59-60, 71
See also Molluscan shellfish; Fish
Cleanability
carpeting, 107
ceilings, 107-108 floor and wall junctures, 107
floors, 103-105
food-contact surfaces, 72-73 mats and duckboards, 107
nonfood-contact surfaces, 77
studs, joists, and rafters, 107
utility lines, 107
wall and ceiling attachments, 107 wall and ceiling coverings and coatings, 107
walls, 107-108
Cleanable fixtures, plumbing system, 97-98
Cleaned in place. See CIP
Cleaners. See Poisonous or toxic materials Cleaning agents
handwashing, 110
warewashing equipment, 86 Cleaning and sanitizing
equipment and supplies for reuse, recyclables,
and returnables, 103-105
equipment and utensils to prevent
food cross contamination, 88-92 knowledge demonstrated by person
in charge, 30-32
maintenance tools, preventing contamination, 113
physical facilities, frequency and restrictions, 112
procedure for employees’ hands and arms, 40-41 ventilation systems, nuisance and discharge
prohibition, 112
Cleaning of equipment and utensils
criteria, 88 frequency, 88-90
methods, 90-91
Cleanliness, personal, of employees
fingernails, 40-42
hands and arms, 40-42 jewelry, prohibition, 42
outer clothing, 42
Clostridium botulinum, preventing growth in reduced, atmosphere packaging, variance, 67-69
See also Time/Temperature Control for Safety Food Clothes washers and dryer
availability, 83
location for contamination prevention, 84 Clothing, outer, of employees, clean condition, 42
Cloths
for use with raw foods of animal origin
treatment, 54-55
for wiping food spills, criteria, 54-55 Code
applicability, 120-121
conformance with history, role in frequency of inspections, 129
Code of Federal Regulations. See “CFR definition”
Cold holding of time/temperature control
for safety food, 62-64
Cold-plate beverage cooling devices, separation from stored ice, design, and construction, 79
Color additive, definition, 13
Commingle, definition, 14 Comminuted, definition, 14
cooking fish and meats, 58
Commissary. See Food establishment definition
Common name, 53
Communicable. See infectious agent Community or individual facility for disposal of refuse,
recyclables, and returnables, 106
Compactors, on-site, 104 Compliance with Code, responsibility of permit
holder, 120-123
Condenser unit, separation from food and food
storage space, 79
Condiments, protection from contamination by consumers, 57 Conditional employee
definition, 14
responsibilities, 33-35 Conditioning device, plumbing system
design, 98
location, 99
Confidentiality, trade secrets, 123
Confirmed disease outbreak, definition, 14 Construction
food establishment, plans and specifications
requirement, 121-123.
inspection and approval, 123
mobile water tank and mobile food establishment water tank, 100-101
plumbing system, 97-98
Consumer advisory for raw or undercooked
animal foods, 71
definition, 15
food on display, protection from
contamination by, 57 information requirements, 71
self-service, clean tableware for refills, 55-56
self-service operations, protection from
contamination, 55-56
Consumer-owned container, refilling, 55-56 Consumers at risk, advisory for fully cooked
animal foods, 71-72
Contact time, chemical sanitization of equipment food-contact
4
surfaces and utensils, 92 Container prohibitions for poisonous or toxic
materials, 116-117
Containers
food storage, common name identification, 53
poisonous or toxic materials labeling and identification, 115
use prohibition, 116
working, common name identification, 72 See also Single-service articles
Contaminated food, disposition, 72 Contamination of food after receiving, prevention, 52-58
Contamination prevention, location of equipment,
clothes washer/dryers, and storage cabinets, 84-85 Control of foodborne disease transmission
by employees, 133-136
Controlled atmosphere packaging
See Reduced oxygen packaging
Conversion of food establishment, plans and specifications, requirement, 121-122
Cook-chill packaging
See Reduced oxygen packaging Cooking
equipment, cleaning frequency, 90
destroying organisms of public health
concern, 58-61
requirements for raw animal foods, variance, 60 utensils. See Kitchenware
Cooling
capacity, food equipment, 82-83 methods to limit growth of organisms of
public health concern, 63-64
time/temperature control for safety food, 63
Copper and copper alloys,
use limitation in food contact and fittings, 75 Core item, definition, 15
Core item violation, time frame for correction, 132
Corned beef roasts minimum holding times for cooking, 59
oven parameters for cooking, 58
Correction of priority violation, 24
time frame, 130-132
timeliness, 131 verification and documentation, 131
Correction of priority foundation violation, 24
Corrective action compliance, 126
failure to demonstrate compliance, 129-130
Corrosion-resistant material, definition, 15
Cosmetics. See Personal care items
Counter guards. See Food display Counter-mounted equipment
definition, 15
elevation, 85
Critical control points
definition, 15 flow diagram, 122
knowledge demonstration by person in
charge, 30-32 monitoring, responsibility of permit holder, 126
standard operating procedures, 122
Critical limit
definition, 15
nonconformance documentation, 129-130 violations, timely corrections, 131
Cross connection, water supply system, prohibition, 99-100
Cross contamination of food protection by separation
and segregation, 52
Crustacea shells, use limitation, 88 Crystal utensils, lead limitation, 74
Cups, refilling in consumer self-service, 55-56
See also Tableware
Cut, infected. See Lesion, containing pus Cut leafy greens
as TCS food, 27
definition, 15
Cutting surfaces
materials, 75 resurfacing, 85
Data plate, warewashing machine, 77
Date marking of ready-to-eat, time/temperature control for safety food, 64-65
Shellstock, 50
Dealer’s tag/label for molluscan shellstock requirements, 48-49
Deli tissue, use to avoid contaminating food, 51
Demonstration of knowledge.
See Person in Charge; Supervision
Denial of application for operating permit, notice, 125 Design, construction, and installation
equipment and utensils acceptability, 82
acceptability, 82 accuracy, 77-78
cleanability, 76-77
durability and strength, 76
functionality, 78
physical facilities cleanability, 107 functionality, 108-109
mobile water tank and mobile food
establishment water tank, 100-102 plumbing system, 97-100
sewage system, 102-103, 105
Design standard, backflow prevention device, 98
Detergents. See Cleaning agents
Detergent-sanitizers for warewashing equipment, 88
rinsing procedures, 91
Deviations from code documentation, 129-130 See also Modifications; Variance; Waivers;
Devices. See Physical facilities
Diarrhea, employee symptom, 33
Dipper wells. See Utensils, in-use storage
Disease of employee, 33-39 Disease or medical condition, reporting responsibility, 33-35
Disease outbreaks caused by Norovirus, S. Typhi, Shigella spp.,
or Shiga producing E. coli, or hepatitis A virus, 34-35 Dish basket. See Basket
Dishes. See Tableware
Dishwashing. See Warewashing
Disinfection
drinking water system, 96 mobile water tank and mobile food establishment
water tank, 100-101
Dispensing equipment, design and construction for
protection of equipment and food, 78-79
Dispensing tube, bulk milk container, 88 Display. See Food display
Disposable towels, waste receptacle, 104
Disposal facilities refuse, recyclables, and returnables, 103-105
sewage, other liquid wastes, and rainwater 102-103
Disposition of ready-to-eat, time/temperature
control for safety food, 65
Distressed merchandise, segregation and location, 112 Documentation
correction of critical priority violation, 231-132
freezing for parasites, 61
inspection report, 129-130
ROP, 67-69 variances, 120
Dogs in food establishments
patrol and sentry, 114
5
pets, 114 service, 187-188
Dollies. See Case lot handling equipment
Doors
pets in common dining area
of group residence, 113-114 equipment maintenance, 85-86
physical facility, 108
refuse receptacle, 103-104 toilet room, 113
vending machine, 79-82 Drain plugs for equipment and receptacles for refuse,
recyclables, and returnables, 105
Drainage of equipment compartments, 81 Drainage system, food establishment,
design and installation, 102
Drainboards
capacity, 83
cleaning frequency, 85 cleanability, 76-77
warewashing, self-draining, 81
Drains, indirect, 102 walk-in refrigerators, 102
Dressing areas
designation, 111
use by employees, 113
Dried eggs, condition at receipt, 48 Drinking by employees, food contamination prevention, 42
Drinking water
bottled, source, 96 definition, 16
Drinking water systems
approved, 96
flushing and disinfection, 96
Drip prevention, design and construction of ventilation hood systems, 78
Driving surfaces. See Surface characteristics, outdoor
Dry cleaning methods, equipment and utensils, 90 Dry eggs, 48
Dry milk, 48
Dry storage area, definition, 16
Drying agents, criteria, 117-118
Duckboards, cleanability, 106-107 Dustless methods of cleaning floors, 112-113
Easily cleanable, definition, 16
Easily movable, definition, 16
Eating by employees, food contamination prevention, 42
Effective date of Code, 120
Egg boiled, See Time/temperature control
for safety food definition
cooking requirements, 56-60, 77-73
definition, 16
lightly cooked or raw, consumer advisory, 71 liquid, frozen, and dry, condition at receipt, 48
pasteurized, substitute for shell eggs, 53, 72-73
pooling, 53, 57, 72-73 time/temperature control for safety food, 28-29
restricted definition, 25
service to highly susceptible populations, 72-73
Egg product, definition, 17
Eggs, raw, shell condition at receipt, 48
cooling, 63-64
labeling, 45
temperature at receipt, 47
Elderly. See Highly susceptible population Emergency occurrence. See Imminent health hazard
Employee
accommodations, location, 111-112
definition, 17 disease or medical condition, 33-39
dressing areas, number, 111-112
eating, drink, and tobacco use, designated areas, 42
food contaminated by, disposition, 72
hygiene, 42-43 ill, exclusions and restrictions, 35-39
practices, supervision of, 32
prevention of food contamination, 50-52 responsibility to report illness, 33-35
serving high-risk populations, exclusions and restrictions, 35-39.
See also Food employee; Person in charge
Emu. See Ratites Enclosures for refuse, recyclables, and returnables,
operation and maintenance, 103-105
EPA, definition, 17
Equipment
air-drying, 93-94 assessment for Code enforcement, 120-121
case lot handling, 81-82
cleaning criteria, 88-89 cleaning frequency
food-contact surfaces/utensils, 88-90
nonfood-contact surfaces, 89
warewashing, 86
compartments, drainage, 81 cooling, heating, and holding capacities, 82
definition, 17
design and construction, durability and strength, 76 existing, 120-121, 126
fixed, elevation or sealing, installation, 84-85
fixed, spacing or sealing, installation, 84
food-contact surfaces and utensils,
cleaning frequency, 88-90 HACCP plan, 122
location for contamination prevention, 84-85
maintenance, 84-85 necessary replacement, 126
plans, 121-122
reassembly after cleaning, 94-95
repair and adjustment, 84-85
storage, 113 storage prohibitions, 94-95
Equipment certification and classification, 82
Equipment and utensils, dry cleaning methods, 90 precleaning, 90
rinsing procedures, 91
Equipment openings, closures and deflectors,
design and construction, 78
Equipment, utensils, and linens cleaning, 88-91
design and construction, 76-82
laundering lines, 92-93
location and installation, 84-85
maintenance and operation, 85-88 materials for construction and repair, 74-76
numbers and capacities, 82-84
protection of clean items, 93-95 sanitization of equipment and utensils, 92
See also Physical facilities
Escargot. See Fish
Exclude, definition, 17
Exclusion of employee illness, 34-35
infection or disease, 35-36
release, 36-39, 133
removal, 36-39, 133
Exclusion order for infected or diseased employee, 133 Expiration time for time/temperature control for safety, 64-66
Exposure, 33-34
6
Facilities
assessment for Code enforcement, 120-121
disposal, recycling, and refilling of waste, 105
necessary replacement, 127
on-premises for refuse, recyclables, and returnables, 103-104
Facility plans and specifications, submission
and approval, 121-122 Faucet, handwashing sink, 98
Fee for operating permit, issuance criteria, 123-124 Fever with sore throat, employee symptom, 33
Filter, compressed air, for drinking water system, 101
Filtering equipment, hot oil, design and construction, 77 Fingernails
artificial, prohibition, 42
of employees, maintenance, 42
First aid supplies in food establishments, storage;
See Personal care items Fish
consumer self-service, 57
cooking requirements, 58-60 definition, 17
frozen by supplier, freezing records, 61
other than molluscan shellfish, 44, 60
raw, storage, 52-53
recreationally caught, 45-46 use of clean equipment, 88
use of laundered gloves, 93
Fish, lightly cooked or raw aquacultured, 61
consumer advisory, 71
freezing to control parasites, 61
immersion in ice or water, 53
restriction on reduced oxygen packaging, 68 Fitting or tubing, copper and copper alloys, use limitation, 75
Fixtures. See Physical facilities
Flatware. See Tableware Floor drains, cleanability, 107
Floor-mounted equipment, clearance, 84
Floors
absorbent materials, use limitation, 113
and floor coverings, cleanability, 107-108 dustless cleaning methods, 112-113
Flow pressure valve, warewashing machine, 81
Flushing drinking water system, 96
mobile water tank and mobile food
establishment water tank, 101-102
waste retention tanks, 102-103
Flux, use limitation for food-contact surfaces, 74 Fogging devices, cleaning the water reservoir, 99-100
Food
additives, 47, 53, 65, 115-116
characteristics, 44
contact with equipment and utensils, 54 contaminated, 72
cooked, time/temperature control for
safety food, cooling, 68-69 damaged, spoiled, or recalled, storage, 52
definition, 17
destruction of organisms of public health
concern, 58-60
frozen, time/temperature control for safety food, 47, 63
hermetically sealed, source, 45
honest presentation, 12, 70, 120
identity, presentation, and on-premises
labeling, 44-45, 70 in contact with water or ice, storage or display, 53
limitation of growth of organisms of public
health concern, 62, 70
packaged and unpackaged, separation, packaging and segregation, 52-53
packaged, labeling, 44-45, 70-71
protection for contamination, 50-58
specialized preparation methods, variance
requirement, 60, 67, 79-80, 120-121, 122 standards of identity, 70
temperature and time control, limiting growth of
organisms of public health concern, 62-70 vended, time/temperature control for safety
food, original container, 57 Food, time/temperature control for safety guidance
HACCP plan, 122-123
hot and cold holding, 91 preparation, application for permit, 123-125
temperature at receipt, 47
time as public health control, 65-67
Food, ready-to-eat, time/temperature control for safety
date marking, 64-65 disposition, 65
Food Allergy, awareness, 33
Food bank. See Food establishment Food Code
intent, 12
scope, statement, 12
standards, 12
title, 12 Food contact, copper, use limitation, 74
Food-contact surface
assessment for Code enforcement, 120-121 cast iron equipment, use limitation, 74
construction materials, 74
copper, use limitation, 75
cleaning criteria, 88
cleaning frequency of equipment, 89-90 definition, 18
design and construction, cleanability, 76-77
galvanized metal equipment, use limitation, 75 lead, use limitation, 74
linens and napkins, use limitation, 54
lubricating, 94
sanitization criteria, 92
sanitization frequency, 92 sanitization methods for equipment, 92
“V” threads, use limitation, 77
wet cleaning methods for equipment, 91 wood, use limitation, 75-76
Food containers
placement in cooling or cold holding
equipment, 63-64
Food contamination by persons, discarding, 72
by unclean utensils and equipment, 54
prevention after receiving, 50-51
prevention by employees, 50-51
Food display, preventing contamination by consumers, 57-58 Food employee
definition, 18
responsibility to report illness, 33-35 Food establishment
definition, 18
identity information, 123-125
inspection, frequency, 128-129
permit to operate, 123-127 plans and specifications for construction,
conversion, or remodeling, 124
temporary, inspection frequency, 128
Food guards. See Food display
Food management, plans, 122 Food package integrity, 48
Food processing, variance required, 67-68
Food processing plant, definition, 19
7
Food Protection Manager Certification, 32 Food reheated in microwave oven, requirements, 62
Food safety
control measures, HACCP plan, 121-123
intent of Food Code, 12
purpose of Code, 12 Food service establishment. See Food establishment
Food sources,
compliance with food law, 44-45 original containers and records, 49-50
Food specifications for receiving, 44-47 temperature, 47-49
Food-specific container for beverages, refilling, 55-56
Food storage containers, identification of food, 53
preventing contamination from premises, 56-77
prohibited areas, 56
Food temperature measuring devices
accessibility, 83 design and construction, 76
Food vending location/areas
outdoor, overhead protection, 109 See also Food establishment
Food volume, proposed, plans, 122
Foodborne disease
outbreak, definition, 18
prevention, knowledge, 30-31 Foodborne illness
frequency of inspections, 128
transmission by employees, prevention, 133 Foot candles. See Lighting
Fork lifts. See Case lot handling equipment
Forks. See Tableware
Freezing to destroy organisms of public health concern, 61
Frog. See Fish Frozen eggs, condition at receipt, 48
Frozen food
limiting growth of organisms of public health concern, 62
maintain frozen, 62
shipped frozen received frozen, 48
Fruits, raw
cooking, 60 washing, 53
whole or cut, immersion in ice or water, 54
whole, uncut, storage, 53
Galvanized metal, use limitation for utensils
and food-contact surfaces of equipment, 75
Game animal commercially raised for food, 45-47
cooking requirements, 58-60
definition, 19
exotic species, 56-48
limitations as food source, 45-47 wild, field-dressed, limitations
as food source, 47, 57
Gauge cock. See Flow pressure valve Garbage. See Refuse
Garlic. See Time/Temperature Control for
Safety Food definition
Gastrointestinal illness, symptoms of employee, 33
General use pesticide, definition, 17 Glasses, refilling in consumer self-service, 55
Gloves
cloth, laundering frequency, 92-93
handwash before donning, 40-41
single-use, 55 slash resistant, 55-56
Grease traps, in food establishment drainage systems, 102
Ground beef. See comminuted definition
cooking, 58 Guard dog. See Service animal
HACCP plan
compliance, responsibility of permit holder, 126 contents, 122-123
criteria, reduced oxygen packaging, 67-69
critical limits, nonconformance, 130 definition, 19
knowledge by person in charge, 30-32 variances, 67, 122
HACCP principles, failure to demonstrate knowledge, 121
Hair restraints for employees, 43 Hamburger, See comminuted definition
cooking, 58
Hand drying
available at handwashing sink, 110
part of cleaning procedure, 40 Hand, antiseptics, 41
Hand antiseptics for employees, 41
Handling kitchenware, 95
single-service and single-use articles, 94
tableware, 95
Hands and arms of employees clean condition, 40
cleaning procedure, 40
hand antiseptics, 41 when to wash, 40
where to wash, 41
Hands, employees
alternative procedure to No Bare
Hand Contact, 50-52 no bare hand contact with RTE food, 50-52
Handwashing
cleanser, availability, 109 food employees, 50
procedures, special, for employees, 40-41
signage, 110
Handwashing sinks
Automatic, 40 cleanability, 98
design and construction, 98
location and placement, 99-112 maintaining and using, 113
numbers and capacities, 98, 109
operation and maintenance, 99-100
use required, 40-41
water temperature, 98 Handwashing sink, definition, 19
Harvester's tag/label for molluscan shellstock,
requirements, 48-51
Hazard Analysis Critical Control Point. See HACCP plan
Hazard, definition, 19 Health hazard, imminent
discontinuance of operations and reporting
requirement, 131 prevention, Code application, additional
requirements, 120, 131-132
summary suspension of operations, 131
Health practitioner
definition, 19 Health status of employee, required reporting, 129
Heat lamp, shield, 108
Heater, for manual warewashing equipment, 80-81
Heating capacity, food equipment, 82
Hepatitis A virus cause of disease outbreak, 34-36
cause of employee illness, 34
conditions for release of employee from restriction
8
or exclusion, 36-39, 136 Hermetically sealed
container, definition, 19
food, source, 44-45
food containers, cleaning, 52
reheating, food taken from a container, 62 High-risk population. See Highly susceptible population
Highly susceptible population
consumer advisory, 71 definition, 20
exclusions and restrictions of ill employees, 35-36 frequency of inspection, 128
permit application, 124
special requirements, 72-73 Holding capacity, food equipment, 82
Holding tank. See Sewage, holding tank
Holding time, minimum
comminuted meats, 58-59
cooking, roast beef and corned beef, 59-60 Hollowware. See Tableware
Homes and living/sleeping quarters, private,
use prohibition, 109 Honest presentation, intent of Food Code, not misleading, 12
Hooks, slab bacon, 52
Hood. See Ventilation systems
Hot holding of time/temperature control for safety food, 64
Hot water quantity and availability, 97
sanitization of equipment food-contact surfaces
and utensils, 92 Hygienic practices of employees
food contamination prevention, 42-43
hair restraints, 43
handling animals, prohibition, 43
Ice
as food, 48 exterior cooling, prohibition as ingredient, 53
source, 48
storage or display of food in contact with, 53-54
Ice units, separation of drains, design and construction, 79
Identity standards for food, definition, 70 Illness of employee, investigation, 133
Illness prevention, intent of Food Code, 12
Imminent health hazard ceasing operations and reporting, 131
definition, 20
Immunocompromised persons.
See Highly susceptible population
In-place cleaning. See CIP definition Incinerators for solid waste, 105
Individual sewage disposal system,
disposal through approved system, 102
Indoor areas, materials, 106
Infection, employee, symptom, 33-35 Infectious agent, employee freedom from,
removal of restriction, 36-39
Ingredients, HACCP plan, 122 Injected, definition, 20
Insect control
devices, design, and installation, 108
food establishments, poisonous
or toxic materials, 115 maintenance, 113
outer openings protected, 108-109
See also Pest control
Insects, dead or trapped, removal, 113
Inspection, frequency establishing, 128
performance- and risk-based, 128
Inspection order
access to premises and records, 129 Inspection port, enclosed water system, 100
Inspection, preoperational, 123, 125
Inspection report
acknowledgment of receipt, 130
documentation, 129-130 issuance, 130
public information, 131
receipt, refusal to sign acknowledgment, 130 Installation
equipment, 84-85 plumbing system, 97
Institutional food service. See Food establishment,
highly susceptible population Interaction of pH and aw.
See Time/Temperature Control for Safety Food
Interstate Certified Shellfish Shippers List,
sources of molluscan shellfish, 45
Intestinal illness of employee, 33-35 Iodine solutions, chemical sanitization, 87-88
Irreversible registering temperature indicator
provided onsite, 84 utensil surface temperature, 83, 92
Jars. See Single-use articles Jaundiced employee
exclusions and restrictions, 36
removal of exclusions and restrictions, 36-39 symptom, 33-34
Jewelry, employees, prohibition exception, 42
medical alert, 42
Juice
definition, 20 HACCP system, 49
packaged, 49
prohibition, 72-73 service to highly susceptible populations, 72-73
treated, 62
warning label, 62
Junctures, floor and wall, covered and enclosed
or sealed, cleanability, 107-108 Justification, variances, 120-121
Kick plates, removable, design and construction, 77
Kitchenware
definition, 20
handling, 95
Knives. See Tableware
Label, common name on food container, 49-50
Labeling packaged food, 44-45
food labels, 70-71
compliance with law, 70-71 identification, 115
poisonous or toxic materials and personal
care items, 116-117
Lamb. See Meat
Landfills for solid waste, 105 Laundering linens
criteria, 93
frequency, 93
mechanical washing, 93
methods, 93 Laundry facilities, use limitations, 93
Lavatories. See Handwashing facilities
Law, definition, 20
9
Layout, proposed, plans, 121-122 Lead limitation in ceramic, china, crystal,
and decorative utensils, 74
Leafy greens, cut
as TCS food, 27
definition, 15 Lesion, containing pus, 33-34
Light bulbs, protective shielding, 108
Lighting, intensity, 110-11 Linens and napkins, use limitation for
food-contact surfaces, 54-55 Linens
definition, 21
laundering criteria, 93 laundering frequency, 93
laundering methods, 93
mechanical washing methods, 93
soiled, storage methods, 93
storage after cleaning, 93 storage prohibitions, 94-95
Liquid eggs, condition at receipt, 48
Liquid food or ice, dispensing equipment, design and construction, 78-79
Liquid food vending machines, waste receptacle, 81
Liquid waste
drain lines, design and construction, 79
other than sewage, disposal facility, 77 products from vending machines, 81
See also Sewage
Litter, removal, 113 Living/sleeping quarters, separation, 109
Loading soiled items, warewashing machines, 90-91
Location, grease trap, 102
Lockers
designation, 111 location, 111
using, 113
Lubricants, incidental food contact, criteria, 117 Lubricating food-contact surfaces, 94
Maintenance
equipment, storage, 113 refuse areas and enclosures, 103
tools, cleaning, 112
See also Operation and maintenance Major food allergen definition, 21
Management and personnel
employee health, 33-39
hygienic practices, 42-43
personal cleanliness, 40-42 supervision, 30-33
Manager certification, national recognition, 32
Manual warewashing. See Warewashing.
Manufacturers' dating information, 64
Materials construction and repair, surface characteristics, 106
mobile water tank and mobile food
establishment water tank, 100 See also Physical facilities
Mats, floor, cleanability, 107
Meal portions, individual, from bulk container, 65
Meat
cooking requirements, 58-60 cured, 65
consumer self-service, 57
definition, 21
rare or raw, consumer advisory, 71
raw, storage, 52 use of clean equipment, 88-90
use of laundered gloves, 93
Mechanical warewashing. See Warewashing
Mechanically tenderized, 21, 58 Medical condition of employee, 33-39
Medical history of ill employee, 133
Medicines in food establishments
restriction and storage, 118
See also Personal care items Melons, cut. See Time/Temperature Control
for Safety Food Definition.
Menu, proposed, plans, 121-122 Menu items, consumer advisory, 71
Meringue, 53-72 mg/L, definition, 21
Microwave ovens
cooking, 60 reheating food, requirements, 62
safety standards, 85
Milk and milk products, dry, fluid, and frozen,
pasteurized at receipt, 48
Milk, fluid, and milk products cooling, 63
dispensing tube, 88
raw, consumer advisory, 71 source, 44-45
temperature at receipt, 47
Mixing valve, handwashing sink, 98
Mobile facility, alternative water supply, 97
Mobile food establishment application for permit, 123-125
sewage holding tank, capacity and drainage, 102
water tank, inlet, 101 waste removal, 103
Mobile water tank and mobile food establishment water tank
design and construction, 101
flushing and disinfection, 101
materials, 100 numbers and capacities, 101
operation and maintenance, 101-102
Modifications. See also Variance and Waivers Code application, 120-121
conformance with approved procedures, 121
Modified atmosphere packaging.
See Reduced Oxygen Packaging.
Molluscan shellfish commingling, 50
definition, 21
lightly cooked or raw, consumer advisory, 71 original container, requirements, 49-50
packaging and identification, 48
shellfish, source, 45
shucked, original container, labeling, 49-50
tanks, use limitations, 79 tanks, variance, 79
Molluscan shellstock
condition on receipt, 49
cooling, 63
identification specifications, 48-49 temperature at receipt, 47
Mollusk. See Fish
Mollusk shells, use limitation, 88 Mops, drying, 113
Mouthwash. See Personal care items
Moveability, case lot handling equipment, 81-82
Moveable. See Easily moveable
Multiuse utensils and food-contact surfaces, construction materials, characteristics, 74-76
Mushrooms
cultivated wild species, source, 45
wild, source, 45
Mussels, lightly cooked or raw, consumer advisory, 71 See also Molluscan shellfish
10
Napkins, cloth, laundering frequency, 93. See also, Linens National Shellfish Sanitation Program
certification number, 14
Guide for the Control of Molluscan Shellfish, 45
Nitrates, nitrites, and salt for curing,
variance specifications, 67-68 Nonconformance with Code, documentation, 76-77
Non-continuous cooking
definition, 22 criteria, 60
Nondrinking water, quality, 96 Nonfood-contact surfaces
cleaning criteria, 88
cleaning frequency, 90 construction materials, characteristics, 75-76
design and construction, 77
Nontyphoidal Salmonella (NTS)
Employee illness, 33, 37
Reporting, 35 Restriction/exclusion, 35-36
Reinstatement, 32-38
Norovirus employee illness, 33-34
reporting, 35
restriction/exclusion, 35-36
reinstatement, 36-39
Notice of denial of application for operating permit, 72-73 NTS, nontyphoidal Salmonella.
See Nontyphoidal Salmonella (NTS)
Nutrition labeling, 70-71 Nuts in shell, storage, 52
Odors
mechanical ventilation, 111 multiuse equipment materials, 74-75
refuse removal frequency, 105
single-service/use article materials, 76 Off-premise
cleaning services for refuse, recyclables
and returnables, 104
delivery and consumption of time/temperature
control for safety food, application for permit, 124 Oil equipment
“V” threads, 77
filtering, 77 On-site cleaning of returnables, 55-56
Openings, to outdoors, protection against
insects and rodents, 108-109
Operation and maintenance
mobile water tank and mobile food establishment water tank, 101-102
physical facilities, 112-114
plumbing system, 99-100
resumption after suspension, 131
sewage system, 102-103 suspension for imminent health hazard, 131
Organisms of public health concern
destruction, 58-62 growth limitation, 58-69
Outdoor areas, materials, 105
Ostrich. See Ratites
Outdoor refuse areas, curbed and graded to drain, 109
Outdoor walking and driving surfaces, graded to drain, 109 Outside receptacles for refuse, recyclables, and returnables,
design and construction, 104
Outside storage of refuse, recyclables, and
returnables, prohibitions, 104
Oven cooking temperature, 59-60
microwave, 60, 62, 85, 90
Overhead protection for outdoor food vending
and servicing areas, 109 Overwraps, colored, for food, limitations, 70
Ownership change, operating permit, 125
Oysters, lightly cooked or raw, consumer advisory, 71
See also Molluscan shellfish
Package integrity, 48
Packaged, definition, 22 Packaged food
labeling, 44 labels, compliance with law, 70-71
separation and segregation from
unpackaged food, 52 Packaging and identification of shucked
molluscan shellfish, 48-50
Packaging, reduced oxygen
conditions not requiring a variance, 67-70
conditions requiring a variance, 67-68 definition, 24-25
HACCP plan and variance criteria, 67-68
Pallets. See Case lot handling equipment Parasite destruction in fish by freezing, 61
Parts per million. See mg/L, definition
Patrol dogs, 114
Performance-based frequency of inspection, 128
Permit, definition, 22 Permit holder
agreement, replacement of facilities
or equipment, 120 definition, 22
posting in food establishment, responsibility, 126
responsibilities for permit retention, 126-127
See also Employee
Permit renewal, existing food establishment, 125 Permit to operate food establishment, 123-127
Person, definition, 22
Person in charge assignment, 30
definition, 22
demonstration of knowledge, 30-31, 129-130
duties, 32-33
employee responsibility for reporting illness, 31 responsibility to report certain employee illness, 34
responsibilities, rights, and authorities,
explanation, 31-35. See also Employee Personal care items
definition, 22
first aid supplies, storage, 118
in food establishments, storage, 118
labeling and identification, 115 medicines, restriction and storage, 118
operational supplies and applications, 115-118
stock and retail sale, 118
Personal cleanliness, 40-42
Personal medications. See Medicines Personnel, supervision, 32-33
Pest control, 113
outer openings protected, 108-109 See also Insect control; Rodent control
Pesticides in food establishments
application, 116
bait station, 118
restricted use pesticide, conditions of use, 116 restricted use pesticide, criteria, 118
tracking powders, 118
See also Poisonous or toxic materials
Pests, dead or trapped, removal, 113
Pets in group residence dining areas, restrictions, 114 Pewter, use limitation for food-contact surfaces, 74
pH, chemical sanitization, warewashing equipment, 86-87, 92
definition, 22
11
Physical facilities cleaning
floors, dustless methods, 112
frequency and restrictions, 112
maintenance tools, preventing
contamination, 113 ventilation systems, nuisance and
discharge prohibition, 112
controlling pests, 113 definition, 22
design, construction, and installation, 107-109 dressing rooms and lockers, using, 113
drying mops, 113
handwashing sinks, maintaining and using, 110 location and placement, 111
maintaining premises, 113
maintenance and operation, 112-114
materials for construction and repair, 106
minimizing attractants and contaminants on floors, 112-113
numbers and capacities, 110-111
pests, dead or trapped, removal, 113 prohibiting animals, 114
repairing, 112
storage, of maintenance tools, 113
toilet room doors, closing, 113
Pickle barrels. See Single-use articles Pinning. See Injected, definition
Plans and specifications for food establishment
contents, 121-123 facility and operating, requirement, 121-123
issuance criteria for operating permit, 125-126
Plastic tubs, buckets. See Single-use articles
Plates. See Tableware
Plumbing fixture, definition, 23 Plumbing system
air gap, 98
backflow prevention, 98 conditioning device, design, 98
construction, 98
definition, 23
design, 98
device, water system, inspection and service, 99 handwashing sink design and construction, 98
installation, 98
location and placement, 99 materials, 97
numbers and capacities, 98-99
operation and maintenance, 99-100
Poisonous or toxic materials
bait stations, 118 boiler water additives, criteria, 117
chemical sanitizers, criteria, 116
chemicals for washing fruits and vegetables,
criteria, 117
common name, 115 containers, prohibition for food use, 117
definition 23
drying agents, criteria, 117 in food establishments, use conditions, 117
knowledge by person in charge, 30-31
lubricants, incidental food contact, criteria, 117-118
pesticides, restricted use, 116
restriction of presence and use in food establishments, 115-116
storage, separation, 115
tracking powders, 118
See also Pesticides in food establishments
Pork. See Meat Portable. See Easily moveable
Potable water. See Drinking water
Poultry
cooking requirements, 59 consumer self-service, 57
definition, 23
rare or raw, consumer advisory, 71
raw, storage, 52
use of clean equipment, 88-91 use of laundered gloves, 93
Precleaning equipment and utensils, 90
Premises definition, 23
maintenance, 113. See also Physical facilities Presentation of food, 70
Preset tableware, handling, 95
Pressure, water, 98 Pressure spray, wet cleaning, 91
Primal cut, definition, 23
storage on hooks or racks, 52
Priority item, definition, 24
Priority foundation item, definition, 24 Private home, unapproved food source, 44
food operations prohibited, 32, 109
Probe-type price and identification tags. See utensil, 28 Processing at retail, 67-70
Produce. See Fruits, raw; Vegetables, raw
Prosthetic device, 40
Public health protection, Code application 120-121
Public information, inspection report, 131 Public sewage treatment plant,
disposal through approved facility, 102
Public water system, definition, 24
Quaternary ammonium compounds, chemical sanitization, 87
Racks
case lot handling, 81
meat storage, 52 warewasher, 78, 80-81, 85-87
Rainwater, disposal facility, 103. See also Sewage
Rapid
cooling, 63-64
growth. See Time/Temperature Control for Safety Food definition, 28
reheating, 62
Ratites cooking, 58
definition, 16
game animal definition, 19
poultry definition, 23
Ready-to-eat food consumer self-service, utensils and dispensers, 57
definition, 24
time/temperature control for safety food
date marking; disposition, 64-65
Reassembly of equipment after cleaning, 94 Receptacles for refuse, recyclables, and returnables
capacity and availability, 103-104
cleaning, 104 covering, 104-105
design and construction, 103-104
drain plugs, 105
equipment and storage, 104-105
location, 104 maintenance, 104-105
Receptacles for removal of refuse, recyclables,
and returnables, 103-105
Records
availability, responsibility of permit holder, 125-127
fish, freezing raw, 44, 61
HACCP, 121-123
12
HACCP plan conformance, failure to demonstrate, 129-130
molluscan shellstock, 48-50
water system service schedule, 99-100
Recyclables. See Refuse
Recycling facilities, 105 Redeeming machines, location, 104
Reduced oxygen packaging
conditions not requiring a variance, 67-69 conditions requiring variance, 67-68
definition, 24-25 HACCP plan and variance criteria, 67-68
Thawing, ROP frozen fish, 68
Refilling clean tableware, 55-56
consumer self-service, using facilities, 56
returnables, 55-56
Refrigeration, cooling and cold holding, 63-65
Refusal of access application for inspection order, 125
reporting, 129
Refusal to sign acknowledgment of inspection report receipt, 150
Refuse areas and enclosures, maintenance, 104-105
Refuse, definition, 25
Refuse, recyclables, and returnables
cleaning implements and supplies, 104 design and construction, 103-104
facilities, on the premises, 103-104
facilities for disposal and recycling, 105 indoor storage area, design, 104
location, 104
outdoor enclosure, construction, 103
outdoor storage areas, construction materials, 103
outdoor storage surface, design and construction, 103, 108-109
removal, 105
storage, operation, and maintenance, 104-105 storage areas
equipment, and receptacles, location,104
rooms, and receptacles, capacity and
availability, 103-104
storage prohibitions, 104-105 toilet room receptacle, covered, 104
Regulatory authority
definition, 25 responsibilities for permit issuance, 125
Reheating
food from a hermetically sealed container, 62
hot holding, temperature requirements, 62
ready-to-eat food, requirements, 62 Reinstatement
excluded or restricted employee, 35-39
Remodeling of food establishment,
plans and specifications 121-122
Removal, refuse, recyclables, and returnables, 104 Reporting, disease; medical condition
by conditional employee, 33-34
by food employee, 33-34 by permit holder, 126
by person in charge, 34
Reporting, imminent health hazard, by permit holder, 126, 131
Re-service of unopened packaged food and unused
definition, 25 food, prohibition, 57
highly susceptible populations, 73
Responsibilities
food employee reporting illness, 33-34
person in charge duties and authorities, 32-33 person in charge reporting ill employee, 34
permit holder for ceasing operations, 131
permit holder for permit retention, 126
regulatory authority for permit issuance, 125 Restaurant. See Food establishment
Restrict, definition, 25
Restricted use pesticide, definition, 25
Restriction
employee, release, 35-39, 133 infected or diseased employee, 35-39, 133
Restriction order
for infected or diseased employee, 133 service, 133
Restrictions employees, removal, 35-39, 133
ill employees, 35-39
Resumption of operations, 131 Retail food store. See Food establishment
Retention tank. See Sewage, holding tank
Retirement home. See Group residence
Returnables
on-site cleaning and refilling, 55-56 refilling, 55-56
See also Refuse
Reuse of shells, 88. See also Public Health Revocation of permit. See Summary permit suspension
Rhea. See Ratites
Right of appeal, denial of application for operating permit, 125
Rinsing procedures, equipment and utensils, 91
Risk-based frequency of inspection, 128 Roasts, beef and pork
minimum holding times for cooking, 58-59
oven parameters for cooking, 58-59 reheating, 62
Rodent control, 113
in food establishments, poisonous or toxic
materials, 115-118
outer openings protected, 108-109 See also Pest control
Rodents, dead or trapped, removal, 113
Roe. See Fish Roofs, protective barrier, 109
Rooms. See Physical facilities
Safe material, definition, 26 Salad bars, monitoring by food employees, 57-58
Salmonella Typhi
cause of disease outbreak and employee illness, 30-31, 33
employee illness, reporting, 33-34, 129
infection, conditions for employee restriction
or exclusion, 34-35
reporting responsibility of person in charge, 34 Salmonella Typhi-free employee,
removal of restriction or exclusion, 36-37
Sample report, private water system, 96-97
Sampling, water, nonpublic system, 96
Sanitization chemical, manual, 86-88
chemical, warewashing equipment, 86-88
definition, 26 equipment and utensils, 92
hot water temperatures
manual, 86
warewashing equipment, 86
pressure, mechanical warewashing equipment, 86. See also Poisonous or toxic materials
Sanitizing solutions
chemical, determining concentration, 86-88
detergent-sanitizer, rinsing procedures, 91
testing devices, availability, 84 wiping cloth storage, 54-55
Scallops. See Molluscan shellfish
Screening
13
backflow prevention device, 98,99 outer openings protected, 108-109
tank vent, 101
vending machines, 82
water conditioning device, 98
Seafood. See Fish Sealed, definition, 26
Seeing Eye dog. See Service animal
Self-draining warewashing sinks and drainboards, 81 Self-service
clean tableware for refills, 55 consumer, protection from contamination, 57-58
handling of single-service and single-use articles, 95
utensil availability, 83 Sentry dogs. See Patrol dogs
Service animal
care and handling, 42-43
definition, 26
handwashing after handling, 40-41 handling of single-service and single-use, 114
presence in dining and sales area, 113-114
Service sinks availability, 111
plumbing system, numbers and capacity, 98-99
use limitation, 41
Servicing area
definition, 26 outdoor, overhead protection, 109
Serving dishes. See Tableware
Sewage definition, 26
disposal, conveying, 102-103
disposal system, approved, design
and construction, 102-103
holding tank, mobile, 102 Sewage, other liquid wastes, and rainwater
backflow prevention, 102
conveying, 102 disposal facility, 103
drainage, 103
establishment drainage system, design
and installation, 102
mobile holding tank, 102 removal from mobile food establishments, 103
retention, 102
Shatterproof bulbs. See Light bulbs, protective Shielding Shellfish control authority, definition, 26
Shells, use limitation, 88
Shellstock
date marking, 64-65
definition, 26 maintaining identification, 50
Shielding, light, 107-108
Shiga toxin-producing Escherichia coli, definition, 26
Shigella spp.
cause of employee illness and disease outbreak, 30-31, 33
employee illness, reporting, 34-35, 129
infection, conditions of employee restriction or exclusion, 35-36
reporting responsibility of person in charge, 34
removal of restriction or exclusion, 31-37, 39
Shucked shellfish, definition, 27
Shutoff device, vending machine, water or liquid food, 81 Single-service and single-use articles
construction materials, characteristics, 75-76
definition, 27
handling, 95
prohibitions, 94-95 required use, 88
reuse limitation, 88
storage after cleaning, 94
Sink compartment requirements, manual warewashing, 82-83 Sink, handwashing. See Handwashing facilities
Sinks, warewashing
cleaning agents, 86
self-draining, 81
use limitations, 86 Slacking
definition, 27
time/temperature control for safety food, conditions, 62-63
Slash-resistant gloves, 55 Sleeping quarters. See Living/sleeping quarters
Smoking. See Tobacco use by employees
Smooth, definition, 27 Sneeze guards. See Food display
Sneezing, coughing, or runny nose by employees,
food contamination prevention, 42-43
Soap. See Cleaning agents
Soiled tableware, handling, 95 Solder, use limitation for food-contact surfaces, 74
Source, approved
drinking water, 96 food, 44-45
shellfish, 45, 48-49
Sous vide packaging. See Reduced Oxygen Packaging
Spacing carpet installation, 107
counter-mounted equipment, 85
equipment installation, 84-85 fixed equipment, 84-85
toxic material separation, 115, 117-118
Spatulas, use to avoid contaminating food, 50
Specifications. See Plans
Sponges, use limitation, 75 Spoons. See Tableware
Spot cleaning. See Floors, dustless cleaning methods
Sprouts, seed. See Time/temperature control for safety food definition, variance, 67-68
Stainless steel. See Cleanability; Easily cleanable
Standards of identity, 70. See also Juice definition
Standards, Food Code, 12
Steak, whole-muscle intact beef, 44-45, 59-60 Steak tartare, consumer advisory, 71
Steam
cleaning equipment, 104 mixing valves, 98
tables, temperature measurement, 80
ventilation, 111
Stitch pumping. See Injected
Stirrers. See Single-service articles Stock and retail sale of poisonous or toxic materials
and personal care items, storage and display, 118
Storage
clean equipment, utensils, linens, and single-service
and single-use articles, 94 first aid supplies in food establishments, 118
food in contact with water or ice, 53-54
maintenance equipment, 113 medicines in food establishments, 118
methods for soiled linens, 93
poisonous or toxic materials, separation, 116
refuse, recyclables, and returnables, operation
and maintenance, 104-105 Storage and display of items for stock and retail sale,
separation, 119
Storage areas for refuse, recyclables, and returnables
capacity and availability, 104
designated, 112 location, 104
Storage cabinets, location for contamination prevention, 84
Storing food to prevent cross contamination, 50-52
14
Straws. See Single-service articles Street foods. See Food establishment, definition, mobile
Studs, joists, and rafters, cleanability, 108
Stuffing, cooking, 58
Sulfites. See Additives
Summary permit suspension disease intervention measure, 133
Summary suspension of operations for imminent
health hazard, 131 Supervision of personnel
demonstration of knowledge, 30-31 person in charge, 32-33
Surface characteristics
indoor areas, 106 outdoor areas, 106, 109
Sweeping compounds. See Floors, dustless cleaning methods
Table-mounted equipment definition, See counter-mounted equipment
definition, 15
elevation, 85 Tablecloths. See Linens
Tableware
clean, consumer use in self-service area,
supervisor responsibility, 32-33
definition, 27 handling, 95
preset, handling, 95
soiled and clean, handling, 95 See also Single-service articles
Tag/label, for molluscan shellstock
record keeping, 50
requirements, 48-49
Take-home food containers, refilling, limitations, 55-56 TCS food. See time/temperature control for safety food
Temperature – Food
cold and hot food holding, 64 cooking, 58-61
cooling, 63-64
plant food, 60
receiving, 47
reheating, 62 roast beef and corned beef, 58-59
seared steak, see steak, whole-muscle intact
thawing TCS food, 63 Conditions, 63
ROP frozen fish, 63
Temperature – Warewashing
wash water, manual, 86
wash water, mechanical, 86 sanitization, manual, 86-88
sanitization, mechanical, 86-88
Temperature measurement devices accuracy,
calibration, 88
definition, 27 design and construction, 76-78
food, provided and accessible, 83
food storage unit air, 77 manual warewashing, accessibility, 83
probe, small diameter, 83
scale, 77
warewashing machines, 80-81
Tempered water, handwashing sink, 98 Temporary facility, water availability, 97
Temporary food establishment
application for permit, 123-125
construction materials, 106
definition, 27 Testing kit for sanitizing solutions, availability, 84
Thawing time/temperature control for safety food,
conditions, 63
ROP frozen fish, 63 Thermistor, thermocouple, thermometer.
See Temperature measuring device
Threads, “V”-type, 77
Three compartment sinks
See Sink compartment requirements Time as public health control for time/temperature, 66
in highly susceptible populations (HSP), 66
Time frame correction of priority item or priority
foundation item violation, 131 Core item violation, 131-132
Time/temperature control for safety food definition, 28-29
Tobacco use by employees, food contamination prevention, 42
Tofu, immersion in ice or water, 53
Toilet rooms
convenience and accessibility, 111
doors, closing, 113 enclosed, design and installation, 108
numbers, 98, 110
receptacle for sanitary napkins, 104 Toilet tissue, availability, 110
Toiletries. See Personal care items
Toilets and urinals
number, 98
use limitation, 98 Tongs, use to avoid contaminating food, 50
Toothpaste. See Personal care items
Toothpicks. See Single-service articles Towelettes, chemically treated, for handwashing,
conditions, 98
Towels
availability, 110
disposable, waste receptacle, 110 Toxic. See Poisonous or toxic materials
Tracking powder. See Pesticides in food establishments
Trade secrets protection, 123
Training plan, food safety,
for employees and for bare hand contact, 32-33
supervisors, HACCP plan, 122
ROP, 33 Training of employees, 33, 68, 73, 122
Transport
case lot moving, 81-82 game animals, 45-46
insulated containers, 80
refuse vehicles, 105
sewage vehicles, 102-103
soiled linens, 93 transportation vehicle, 18
water vehicles, 97
Trash. See Refuse
Tumblers. See Tableware
Tuna, 61 Turtle. See Fish
Two compartment sinks
See Sink compartment requirements
Unnecessary
items, 105-113
ledges, projections and crevices, 77 persons, 32
Urinals, numbers, 98
"Use by” date. See Date marking
Utensils
air-drying, 93-94 cast iron, use limitation, 74
ceramic, china, crystal, and decorative,
lead limitation, 74
15
cleaning criteria, 88-90 cleaning frequency, 88-90
consumer self-service, availability, 83
contact with food, 54
definition, 28
design and construction, durability and strength, 76 galvanized metal, use limitation, 75
in-use storage, 54
maintenance and operation, 88 multiuse, construction materials, 74-75
racks, capacity, 83 sanitization, 92
serving, for consumer self-service operations, 57
storage after cleaning, 89-95 storage between use, 54
wet cleaning methods,91
Utility lines, cleanability, 107
"V" threads, use limitation for food-contact surfaces, 77
Vacuum packaging. See Reduced oxygen packaging
Variance cooking raw animal foods, 58-61
conformance with approved procedures, 121
definition, 29
HACCP plan, 121, 122-123
modifications and waivers, Code application, 120-121
molluscan shellfish tanks, 79
rationale, 121 requirement for specialized food
processing methods, 67
sprouting, 67
Vegetables, raw
cooking for hot holding, 60 washing, 53
whole or cut, immersion in ice or water, 53
whole, uncut, raw, storage, 52 See also Sprouts; time/temperature control
for safety food definition
Vehicles for removal of refuse, recyclables,
and returnables, 105
Vending machines automatic shutoff, 79-80
can openers, design and construction, 79
condiments, packaging to prevent contamination, 79
definition, 29
design and construction of vending
stage closure, 79
doors and openings, design and construction, 82 liquid waste products, 81
location, definition, 29
time/temperature control for safety food,
original container, 79-80
refuse receptacles in, 104 temperature, 79-80
Ventilation, mechanical, 78
Ventilation systems capacity, 83
cleaning, nuisance and discharge prohibition, 77-78
exhaust vents, design and installation, 76
hood, adequacy, 83
drip prevention, design and construction, 78 Verification of correction of priority item and priority
foundation item violation, 131
Vermin. See Insect control; Pest control; Rodent control
Violations, priority item and priority foundation item,
continuing, 131 demonstration of knowledge compliance
with Code, 30-31
documentation and verification of correction, 131
documentation of findings, 129-130 history of, role in frequency of inspections, 123-125
inspection and correction, 128-132
uncorrected, 130
Core item, time frame for correction, 131-132
timely correction, 131 Virus. See Disease outbreaks caused by
Vomiting, employee symptom, 33-38
Waivers. See also Modifications; Variance Code requirements, 120
conformance with approved procedures, 121
Walk-in refrigerator, carpeting prohibition, 106 drains, 107
Walking surfaces. See Surface characteristics
Wall and ceiling coverings and coatings, cleanability, 107-108
Walls, exterior, protective barrier, 109
Warewashing definition, 29
manual, sink compartment requirements, 82-83
manual, temperature measuring devices, accessibility, 83
mechanical, temperature measuring devices,
accessibility, 83
Warewashing equipment chemical sanitizer concentration,
determining, 86-87
clean solutions, 86 manual
alternative, 82-83
chemical sanitization, 92
detergent-sanitizers for chemical
sanitization, 87 cleaning agents, 83
heaters and baskets, 81
hot water sanitization rinsing, 91 temperatures, 83, 86-87, 92
wash solution temperature, 86
mechanical chemical sanitization, 86-87
hot water sanitization temperatures, 86
sanitization pressure, 77, 81, 87 wash solution temperature, 86
Warewashing machines
data plate operating specifications, 80 drain connection, 102-103
flow pressure valve, 81
internal baffles, 80
loading of soiled items, 90-91
manufacturers' operating instructions, 86 sanitizer level indicator, 81
temperature measuring devices, 80
Warewashing sinks
alternative use limitation, 82, 86
and drainboards, self-draining, 81 Warning not required for hold order, 133
Wash solution temperature, warewashing equipment, 86
Washers/dryers, clothes, availability, 83 Washing,
mechanical methods, linens, 84, 93
methods, equipment, and utensils, 90-91
raw fruits and vegetables, 53
Waste liquid. See Sewage
solid. See Refuse
Waste receptacle for disposable towels, 110
Waste retention tank, flushing, 103
Water alternative supply, 97
distribution, delivery, and retention, 97
hot, quantity and availability, 97
16
inlet/outlet, protective device, 96 nondrinking, 96
pressure, 97
quality, 96
sample report, 96
sampling, 96 standards, 96
quantity and availability, 97
source approved system, 96
bottled drinking, 96 capacity, 97
disinfection, 96
knowledge by person in charge, 31 system flushing, 96
storage or display of food in contact with, 53
Water activity, definition, 13
Water conditioning device, 98
Water reservoir of fogging devices, cleaning, 99-100 Water supply
alternative supply, 97
system, prohibition of cross connection, 99 Water system, compressed air filter, 101
Water system device,
inspection and service, 99
Water systems, public and nonpublic, 96
Water tank hose, construction and identification, 101
inlet/outlet and hose fitting, protection, 101-102
sloped to drain, 101 use limitation of "V" type threads, 101
pump, and hoses, dedicated use, 102
vent, protected, 101
Watertight joint, equipment openings, 78
Water treatment device, 99 Wet cleaning methods, equipment and utensils, 91
Wet storage. See Storage, food in contact with water and ice;
Molluscan shellfish, tanks Wetting agents, 91
Whole-muscle, intact beef
definition, 29
consumer advisory exemption, 44-45, 71
cooking, 58-60 labeling, 45, 59-60
Windows, tight-fitting, 108-109
Wiping cloths air-drying locations, 93-94
laundering, 93
stored in sanitizer, 57
use for one purpose, 54-55
Wood, use limitation for food-contact surfaces, 75-76 Work clothes. See Clothing, outer
Wound, infected. See Lesion, containing pus
Wrapped food
honestly presented, 44, 70
preventing contamination, 52, 53, 56, 58 See also packaged, definition
Wrapped tableware, handling, 95